• 한국농공학회논문집
• /
• 제52권3호
• /
• pp.73-79
• /
• 2010

In the present study, the loading frequency dependencies of cyclic shear strength and elastic shear modulus of reconstituted clay were examined by performing undrained cyclic triaxial tests and undrained cyclic triaxial tests to determine deformation properties. The result of undrained cyclic triaxial test of reconstituted and saturated clay shows that a faster frequency leads to higher stress amplitude ratio, but when the frequency becomes fast up to a certain point, the stress amplitude ratio will reach its maximum limit and the frequency dependence becomes insignificant. And also, the result of undrained cyclic triaxial deformation test shows a fact that a faster loading frequency leads to higher equivalent shear modules and smaller hysteresis damping ratio, and confirms the frequency dependence of cohesive soil. Meanwhile, the result of the creep test shows that continuing creep is created in the undrained cyclic triaxial test with slow loading frequency rate, and since loading rate becomes slower at the vicinity of the maximum and the minimum deviator stress due to sine wave loading, the vicinity of the maximum and the minimum deviator stress shall be more influenced by creep.

• 한국지반공학회논문집
• /
• 제22권10호
• /
• pp.151-163
• /
• 2006

본 논문에서는 모래의 비배수 정적전단거동과 반복전단거동의 상호관계를 분석하기 위하여 낙동강 모래를 사용하여 비배수 정적 및 반복삼축시험을 실시하였다. 정적삼축시험은 반복전단거동과의 상호비교를 위하여 인장시험을 포함하여 실시하였다. 그리고 반복삼축시험은 초기정적전단응력$(q_{st})$과 반복응력$(q_{cy})$조건을 조합하여 여러 응력조건 하에서 실시하였다. 시험결과 반복전단거동의 응력경로는 정적전단거동의 한계응력비(CSR)선을 지나면서 유동변형이 발생하여 정적전단거동과 일치하였으며, 그 후 정적전단거동의 파괴선(FL)을 따라 파괴가 발생하였다. 이러한 반복 전단거동의 응력경로는 시험방법이 다름에 따른 약간의 차이는 있으나 정적전단거동의 응력경로와 본질적으로 동일함을 알 수 있었다.

• Geomechanics and Engineering
• /
• 제25권2호
• /
• pp.89-98
• /
• 2021

The paper presents an experimental study on the strength behaviour of a coral gravelly sand from Vietnam subjected to monotonic and cyclic loading. A series of direct shear tests were carried out to investigate the shear strength behaviour and the factors affecting the shear strength of the sand such as relative density, cyclic load, amplitude of the cyclic load and loading rate. The study results indicate that the shear strength parameters of the coral gravelly sand include not only internal friction angle but also apparent cohesion. These parameters vary with the relative density, cyclic load, the amplitude of the cyclic load and loading rate. The shear strength increases with the increase of the relative density. The shear strength increases after subjecting to cyclic loading. The amplitude of the cyclic load affects the shear strength of coral gravelly sand, the shear strength increases as the amplitude of the cyclic load increases. The loading rate has insignificantly effect on the shear strength of the coral gravelly sand.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 가을 학술발표회 논문집
• /
• pp.285-292
• /
• 1999

The cyclic plate load test were peformed to determine the behavior of reinforced soft ground with multiple layers of geogrid. Five series of test were conducted with varying the soil profile conditions which including the ground level, type of soil, and the thickness of each soil layer. The plate load test equipment was slightly modified to apply the cyclic load. Based on the cyclic plate load test results, the bearing capacity ratio(BCR), subbase modules, shear modules, the elastic rebound ratio, and reinforcing parameters are presented.

• Geomechanics and Engineering
• /
• 제10권1호
• /
• pp.1-19
• /
• 2016

This paper presents the results of an intensive experimental investigation on cyclic behavior of various sands and structural materials interface. Comprehensive measurements of the horizontal displacement and shear stresses developed during testing were performed using an automated constant normal load (CNL) cyclic direct shear test apparatus. Two different particle sizes (0.5 mm-0.25 mm and, 2.0 mm-1.0 mm) of sands having distinct shapes (rounded and angular) were tested in a cyclic direct shear testing apparatus at two vertical stress levels (${\sigma}=50kPa$, and 100 kPa) and two rates of displacement ($R_D=2.0mm/min$, and 0.025 mm/min) against various structural materials (i.e., steel, concrete, and wood). The cyclic direct shear tests performed during this investigation indicate that (i) the shear stresses developed during shearing highly depend on both the shape and size of sand grains; (ii) characteristics of the structural materials are closely related to interface response; and (iii) the rate of displacement is slightly effective on the results.

• Steel and Composite Structures
• /
• 제14권6호
• /
• pp.587-604
• /
• 2013

There are few technical documents regulated structural performance and engineering criteria in domestic market for Structural insulated panels in Korea. This paper was focused to identify fundamental performance under monotonic loading and cyclic loading for SIPs in shear wall application. Load-displacement responses of total twelve test specimens were recorded based on shear stiffness, strength, ultimate load and displacement. Finally energy dissipation of each specimen was analyzed respectively. Monotonic test results showed that ultimate load was 44.3 kN, allowable shear load was 6.1 kN/m, shear stiffness was 1.2 MN/m, and ductility ratio was 3.6. Cyclic test was conducted by two kinds of specimens: single panel and double panels. Cyclic loading results, which were equivalent to monotonic loading results, showed that ultimate load was 45.4 kN, allowable shear load was 6.3 kN/m. Furthermore the accumulated energy dissipation capability for double panels was as 2.3 times as that for single panel. Based on results of structural performance test, it was recommended that the allowable shear load for panels should be 6.1 kN/m at least.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 1999년도 춘계 학술발표회 논문집 Proceedings of EESK Conference-Spring
• /
• pp.77-84
• /
• 1999

An assessment of liquefaction potential is made in principle by comparing earthquake induced shear stress to the liquefaction strength of the soil. In this research a modified method based on Seed and Idriss theory is developed for evaluating liquefaction strength of Jumunjon sand(Korean standard sand). Also the factors affecting liquefaction strenght such as cyclic shear stress amplitude and relative density are investigated and verified by using cyclic triaxial test. From the result the new relationships between cyclic shear stress ratio and number of load cycles are proposed for evaluating liquefaction strength under moderated magnitude(M=6.5) of earthquake.

• 복합신소재구조학회 논문집
• /
• 제4권1호
• /
• pp.33-39
• /
• 2013

Structural insulated panels, structurally performed panels consisting of a plastic insulation bonded between two structural panel facings, are one of emerging products with a viewpoint of its energy and construction efficiencies. These components are applicable to fabricated wood structures. In Korea, there are few technical documents regulated structural performance and engineering criteria in domestic market. This study was conducted to identify fundamental performance of both monotonic load and quasi static cyclic load for SIPs in shear wall application. Static test results showed that maximum load was 44.3kN, allowable shear load was 6.1kN/m, shear stiffness was 1.23 M N/m, and ductility ratio was 3.6. Cyclic test was conducted by two kinds of specimens : single panel and double panels. Cyclic test results, which were equivalent to static test results, showed that maximum load was 45.42kN, allowable shear load was 6.3kN/m. Furthermore the accumulated energy dissipation capability for double panels was as 2.3 times as that for single panel. From performance of structural tests, it was recommended that the allowable shear load for panels was at least 6.1kN/m.

• 한국지반신소재학회논문집
• /
• 제13권2호
• /
• pp.49-57
• /
• 2014

본 연구에서는 남극 장보고기지 부근에서 채취한 시료를 활용하여 동하중에 대한 액상화 저항특성을 파악하기 위하여 반복삼축시험을 실시하였다. 또한 기존문헌과의 비교를 통하여 남극에서 퇴적된 지반의 동적거동을 규명하였다. 시험결과 동일한 압밀응력비에 대한 반복회수와 축변형률 5%를 발생시키는데 필요한 반복응력비와의 관계는 모든 시료에서 초기액상화를 발생시킬 수 있는 반복응력비가 증가할수록 반복회수가 감소하였다. 세립분 함유량이 10%로 증가할수록 액상화 저항강도가 감소하다가 다시 증가하는 경향을 나타내었다. 점착력과 액상화 저항강도와의 관계는 세립분 함유량과 액상화 저항강도와의 관계와 같이 점착력이 증가할수록 액상화 저항강도도 감소하지만 어느 시점 이후에는 반복응력비가 증가하는 경향을 보였다. 또한, 마찰각과 평균입경이 증가할수록 반복응력비가 증가하는 경향을 나타내었다.

• Geomechanics and Engineering
• /
• 제13권5호
• /
• pp.809-823
• /
• 2017

This paper describes lab test results of artificial rock-like material samples having a plane joint. Cyclic shear tests were performed under different normal loads and different shear displacement amplitudes. For this purpose, multi-stage normal loading tests (30 kN, 60 kN, 90 kN, 180 kN, 360 kN and 480 kN) with cyclic excitation at frequency of 1.0 Hz and different shear displacement amplitudes (0.5 mm, 1.0 mm, 2.0 mm, 4.0 mm, 5.0 mm, and 8.0 mm) were conducted using the big shear box device GS-1000. Experimental results show, that shear forces increase with the increase of normal forces and quasi-static friction coefficient is larger than dynamic one. With the increase of normal loads, approaching the peak value of shear forces needs larger shear displacements. During each cycle the normal displacements increase and decrease (rotational behavior in every cycle). Peak angle of inclination increases with the increase of normal load. A phase shift between maximum shear displacement and maximum shear force is observed. The corresponding time shift decreases with increasing normal load and increases with increasing shear displacement amplitudes.