• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 C
• /
• pp.2274-2276
• /
• 2005

Cyclic aging for 14days is performed to remove the large amount of the volatiles found in freshly manufactured cable. In this paper, we examined lightning impulse characteristics of power cable before and after cyclic aging for 14days. As the result, the breakdown voltage after aging was lower than that before aging, but the breakdown voltage after aging was higher than that before aging in TR CNCV-W $60mm^2$ power cable.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2001년도 봄 학술발표회 논문집
• /
• pp.517-524
• /
• 2001

In this study, the effect of relative density and fine contents(Finer then # 0.08mm sieve) on liquefaction phenomenon in reclaimed land by hydraulic hammer compaction is analyzed. For more site-specific studies, reclaimed land in Inchon International Airport is selected and the cyclic triaxial tests are performed on disturbed samples. In cyclic triaxial tests, the characteristics of reclaimed land in Inchon International Airport are considered sufficiently. The liquefaction resistance stress ratio ($\tau$$\ell$/$\sigma$v') can be defined by relative density 40, 50, 60, and 70% and also by fine contents : 0, 10, 20, 30, and 40% under relative density (D$\_$r/) 50% used disturbed samples. From tile result of comparing tile cyclic triaxial tests, it is shown that the liquefaction strength of soil increases with increases of relative density and fine contents. Fspecially fine contents is the main factor affecting the liquefaction potential. In addition, the liquefaction resistance stress ratio is reduced by the increase of fine content and tile ratio of change is steep until fine contents 20% and that is flexible during the range of fine contents 20% to 40%. Through this study, it is proved that the soil characteristics (fine contents 5∼20%) of the reclaimed land in Inchon International Airport flays an important role in the reduction of liquefaction potential.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.169-174
• /
• 2001

Low cycle fatigue tests are performed on high strength low alloy steels that be developed for submarine material. The relation between absorbed plastic strain energy and numbers of cycle to failure is examined in order to predict the low cycle fatigue life of structural steels by using plastic strain energy method. The cyclic properties are determined by a least square fit techniques. The life predicted by the plastic strain energy method is found to coincide with experiment data and results obtained from the Coffin-Manson method. Also the cyclic behavior of structural steels is characterized by cyclic softening with increasing number of cycle at room temperature. Especially, low cycle fatigue characteristics and microstructural changes of structural steels are investigated according to changing tempering temperatures. In the case of PFS steels, the $\varepsilon$-Cu is formed in 550C of tempering temperature and enhances the low cycle fatigue properties.

• Nuclear Engineering and Technology
• /
• 제45권1호
• /
• pp.89-98
• /
• 2013

In recent years steel-concrete composite shear walls have been widely used in enormous high-rise buildings. Due to high strength and ductility, enhanced stiffness, stable cycle characteristics and large energy absorption, such walls can be adopted in the auxiliary building; surrounding the reactor containment structure of nuclear power plants to resist lateral forces induced by heavy winds and severe earthquakes. This paper demonstrates a set of nonlinear numerical studies on I-shaped composite steel-concrete shear walls of the nuclear power plants subjected to reverse cyclic loading. A three-dimensional finite element model is developed using ABAQUS by emphasizing on constitutive material modeling and element type to represent the real physical behavior of complex shear wall structures. The analysis escalates with parametric variation in steel thickness sandwiching the stipulated amount of concrete panels. Modeling details of structural components, contact conditions between steel and concrete, associated boundary conditions and constitutive relationships for the cyclic loading are explained. Later, the load versus displacement curves, peak load and ultimate strength values, hysteretic characteristics and deflection profiles are verified with experimental data. The convergence of the numerical outcomes has been discussed to conclude the remarks.

• Geomechanics and Engineering
• /
• 제37권4호
• /
• pp.359-370
• /
• 2024

The primary goal of this study is to evaluate the migration of fine granular materials into overlying layers under cyclic loading using a modified large-scale triaxial system as a physical model test. Samples prepared for the modified large-scale triaxial system comprised a 60 mm thick gravel layer overlying a 120 mm thick subgrade layer, which could be either tailings or railway sand. A quantitative analysis of the migration of fine granular materials was based on the mass percentage and grain size of migrated materials collected in the gravel. In addition, the cyclic characteristics, i.e., accumulated axial strain and excess pore water pressure, were evaluated. As a result, the total migration rate of the railway sand sample was found to be small. However, the total migration rate of the sample containing tailings in the subgrade layer was much higher than that of the railway sand sample. In addition, the migration analysis revealed that finer tailings particles tended to be migrated into the upper gravel layer easier than coarser tailings particles under cyclic loading. This could be involved in significant increases in excess pore water pressure at the last cycles of the physical model test.

• 한국자동차공학회논문집
• /
• 제4권6호
• /
• pp.65-77
• /
• 1996

A small-sized industrial diesel engine was converted to a spark ignited engine and then adapted for fuelling with natural gas. After conversion work, general combustion characteristics of the gas engine(such as ignition delay, main and total combustion durations, and heat release characteristics) were studied as a functio of major engine operating variables such as air to fuel ratio, spark timing, and spark plug type. Some other studies on cyclic variation characteristics in IMEP, Pmax and (dp/dφ)max, and also optimum combustion phasing angle were performed.

• 한국지반공학회논문집
• /
• 제19권2호
• /
• pp.57-64
• /
• 2003

지진하중조건에서 포화된 모래의 액상화 가능성은 심도 있는 연구가 진행되어 왔다. 이러한 연구에서 대표적인것은 실험실에서 반복삼축압축시험에 의하여 모래의 반복강도를 결정하는 것이다. 본 연구는 재성형된 포화 균등모래의 액상화 특성에 있어서 시편의 성형방법에 따른 영향을 검증하기 위하여 수행되었다. 건조시료의 공기중낙하다짐, 습윤층다짐, 습윤진동층다짐 등 3가지 방법에 의하여 동일한 밀도로 다짐된 포화된 균등한 모래에 대하여 삼축압축시험이 수행되었다. 같은 밀도에서 다른 방법에 의하여 성형된 포화된 균등한 모래의 액상화 저항특성인 반복응력비는 크게 다른 것으로 확인되었다.

• Corrosion Science and Technology
• /
• 제20권2호
• /
• pp.62-68
• /
• 2021

Artificial neural network techniques show an excellent ability to predict the data (output) for various complex characteristics (input). It is primarily specialized to solve nonlinear relationship problems. This study is an experimental investigation that applies artificial neural network techniques and an experimental design to predict the cyclic polarization curves of the super-austenitic stainless steel AL-6XN alloy with sensitization. A cyclic polarization test was conducted in a 3.5% NaCl solution based on an experimental design matrix with various factors (degree of sensitization, temperature, pH) and their levels, and a total of 36 cyclic polarization data were acquired. The 36 cyclic polarization patterns were used as training data for the artificial neural network model. As a result, the supervised learning algorithms with back-propagation showed high learning and prediction performances. The model showed an excellent training performance (R²=0.998) and a considerable prediction performance (R²=0.812) for the conditions that were not included in the training data.

• 한국지진공학회논문집
• /
• 제12권6호
• /
• pp.65-71
• /
• 2008

본 논문에서는 반복하중에 의한 반복 경화 및 연화 현상을 나타낼 수 있는 수정 IWAN 모델을 이용하여, 1차원 비선형 부지응답 해석프로그램(이하 KODSAP; Kaist One Dimensional Site-response Analysis Program)을 개발하였다. 개발된 프로그램은 지진하중 재하에 따른 지반의 반복경화 및 연화현상에 의한 부지응답 특성 변화를 재현할 수 있다. KODSAP을 이용하여 기반암 상부 40m인 모형지반의 반복경화 및 연화 정도, 지진가속도의 크기에 따른 부지응답특성 변화를 살펴 보았으며, 현재 실무에서 널리 적용되고 있는 등가선형, 비선형해석과 KODSAP 해석결과(지반의 반복경화 및 연화현상을 고려한)과의 차이점을 살펴 보았다.

• 한국지반신소재학회논문집
• /
• 제13권2호
• /
• pp.49-57
• /
• 2014

본 연구에서는 남극 장보고기지 부근에서 채취한 시료를 활용하여 동하중에 대한 액상화 저항특성을 파악하기 위하여 반복삼축시험을 실시하였다. 또한 기존문헌과의 비교를 통하여 남극에서 퇴적된 지반의 동적거동을 규명하였다. 시험결과 동일한 압밀응력비에 대한 반복회수와 축변형률 5%를 발생시키는데 필요한 반복응력비와의 관계는 모든 시료에서 초기액상화를 발생시킬 수 있는 반복응력비가 증가할수록 반복회수가 감소하였다. 세립분 함유량이 10%로 증가할수록 액상화 저항강도가 감소하다가 다시 증가하는 경향을 나타내었다. 점착력과 액상화 저항강도와의 관계는 세립분 함유량과 액상화 저항강도와의 관계와 같이 점착력이 증가할수록 액상화 저항강도도 감소하지만 어느 시점 이후에는 반복응력비가 증가하는 경향을 보였다. 또한, 마찰각과 평균입경이 증가할수록 반복응력비가 증가하는 경향을 나타내었다.