• 한국지반환경공학회 논문집
• /
• 제23권12호
• /
• pp.25-31
• /
• 2022

해양지반에 설치된 구조물은 육상지반에 설치된 구조물과는 달리 해상에서의 파하중, 풍하중, 그리고 조류하중 등과 같은 장기 반복하중을 고려해야 된다. 이에 해양지반에 설치된 구조물을 설계하기 위해서는 장기 반복하중을 받는 지반의 거동을 분석하는 것이 중요하다. 본 논문에서는 반복단순전단시험을 수행하여 구속압에 따른 장기반복하중에 대한 지반거동을 분석하고, 구속압에 따른 파괴특성을 쉽게 확인할 수 있는 3차원 설계파괴곡선을 작성하였다. 분석결과, 동일한 반복전단응력비와 평균전단응력비 조건이어도 구속압에 따라 설계파괴곡선의 위치가 차이가 있었으며, 파괴에 도달하는 반복하중횟수가 구속압에 영향을 받는 것을 확인하였다. 작성한 구속압에 따른 3차원 설계파괴곡선은 구속압에 따른 설계파괴곡선의 경향성과 대략적인 값을 추정할 수 있다.

• 콘크리트학회지
• /
• 제7권2호
• /
• pp.165-174
• /
• 1995

정적하중은 동적하중에 비해 재하속도가 느리므로 보다 합리적인 내진설계 규준제정을 위해서는 정적 실험과 별도로 동적실험이 필요하다. 그러나 구조물의 실물크기로 동적실험을 수행하기에는 여러 가지 기계적, 경제적인 제약이 있으므로 그 크기를 축소시킨 모형실험이 일반적으로 수행되고 있다. 이 연구에서는 11개의 철근 콘크리트 보-기둥 접합부 실험체에 대해 이미 잘 알려진 상사법칙을 적용하여 길이 축척비 1 : 2 : 4로 제작하여, 재하진동수를 0.0025Hz~2.0Hz로 각각 서로 다르게 작용시켜 철근콘크리트 부재의 동적 모형실험에 대한 신뢰성을 검토하였다. 실험결과, 상사법칙에 의해 설계된 모형실험체는 원형크기 실험체의 동적거동 예측에 유용하게 사용 될 수 있음이 확인되었다.

• 한국재난정보학회 논문집
• /
• 제15권2호
• /
• pp.186-197
• /
• 2019

연구목적: 본 연구에서는 대변형 효과를 구현할 수 있는 유한요소 해석기법을 기반으로 반복하중에 의한 스테인리스강의 이력거동을 정확하게 평가할 수 있는 비선형 반복소성 손상모델을 개발하였다. 연구방법: 개선된 운동경화 모델과 등방경화 법칙을 연계하여 반복하중 하에서의 재료의 거동을 모사하는데 필요한 반복소성 모델을 개발하였으며, 이를 비선형 손상모델과 결합하였다. 연구결과 및 결론: 제안된 비선형 손상모델을 검증하기 위하여 변형률 제어 단조 및 반복하중 시험을 모사하였으며, 이를 통한 해석결과를 시험결과와 비교하였다. 비교 결과, 본 연구에서 제안한 비선형 손상모델은 스테인리스강의 반복하중 하에서의 이력거동을 정확하게 모사할 수 있음을 확인하였다.

• Steel and Composite Structures
• /
• 제21권2호
• /
• pp.443-460
• /
• 2016

In this paper, the efficiency and effectiveness of two strengthening methods for upgrading behavior of the two external weak reinforced concrete (RC) beam-column joints were experimentally investigated under cyclic loading. Since two deficient external RC joints with reduced beam height and low strength concrete were strengthened using one-way steel prop and curbs with and without steel revival sheets on the beam. The cyclic performance of these strengthened specimens were compared with two another control external RC beam-column joints, one the standard RC joint that had not two mentioned deficiencies and another had both. Therefore, four half-scale RC joints were tested under cyclic loading.The experimental results showed that these innovative strengthening methods (RC joint with revival sheet specially) surmounted the deficiencies of weak RC joints and upgraded their performance and bearing capacity, stiffness degradation, energy absorption, up to those of standard RC joint. Also, results exhibited that the prop at joint acted as a fuse element due to adding steel revival sheets on the RC beam and showed better behavior than that of the specimen without steel revival sheets. In other words by stiffening of beam, the prop collected all damages due to cyclic loading at itself and acted as the first line of defense and prevented from sever damages at RC joint.

• 대한기계학회논문집
• /
• 제19권6호
• /
• pp.1422-1430
• /
• 1995

Al6061 alloy reinforced with 15 volume% of Saffil fibers was fabricated by squeeze infiltration method. Uniform distribution of reinforcements and good bondings between reinforcements and matrix alloy were found in the microstructure of composites. Comparing with A16061 matrix alloy, tensile strength and elastic modulus of $Al_{2}$O$_{3}$/Al composites were increased up to 26% and 31%, respectively. Cyclic deformation and fatigue behavior of $Al_{2}$O$_{3}$/Al metal matrix composites were studied. The specimens were cycled using tension-tension(R=0.1) loading and under load controlled fatigue test. Cyclic stress-displacement curve through fatigue test was obtained. Fatigue strength of $Al_{2}$O$_{3}$/Al composites was about 200 MPa, i.e.0.55 of applied stress level(q). During fatigue test, $Al_{2}$O$_{3}$/Al composites displayed cyclic hardening at all applied stress levels. The most of resultant displacement due to permanent plastic deformation occurred in less than the first 5% of fatigue life. Displacement-to-failure of the fatigue test was smaller than that of the tensile test because of accumulative damage by cumulative plastic deformation.

• 한국강구조학회 논문집
• /
• 제13권2호
• /
• pp.143-152
• /
• 2001

본 연구에서는 정적 및 반복하중을 받는 강판의 거동특성에 관하여 검토하였다. 강판의 강도에 관한 설계변수로서는 초지처짐과 형상비, 판의 폭-두께비등을 들 수 있으며, FEM해석을 통하여 이상의 설계변수에 관한 영향에 관하여 검토하였다. 정적 압축하중이 작용하는 판의 강도는 형상비가 1.0이하인 경우에는 형상비 변화에 따른 영향이 거의 나타나지 않았으며, 반복하중을 받는 판의 경우 폭-두께비와 변위 진폭의 크기가 강도에 크게 영향을 미치고 있음을 확인하였다. 이러한 해석결과를 기초로 본 연구에서는 반복재하에 의한 강도감소 특성을 고려한 강도곡선식을 제안하였으며, 또한 폭-두께비와 변위 진폭에 따른 판의 변형성능에 관해서 검토하였다

• Journal of Mechanical Science and Technology
• /
• 제14권10호
• /
• pp.1051-1060
• /
• 2000

Linear cyclic systems (LCS's) are a class of systems whose dynamic behavior changes cyclically. Such cyclic behavior is ubiquitous in systems with fundamentally repetitive motions (e. g. all rotating machinery). Yet, the knowledge of the noise and vibration transmission paths in LCS's is quite limited due to the time-varying nature of their dynamics. The first part of this two-part paper derives a generic expression that describes how the noise and/or vibration are transmitted between two (or multiple) locations in the LCS's. An analysis via the Fourier series and Fourier transform (FT) plays a major role in deriving this expression that turns out to be transfer function dependent upon the cycle position of the system. The cyclic nature of the LCS' transfer functions is shown to generate a series of amplitude modulated input signals whose carrier frequencies are harmonic multiples of the LCS' fundamental frequency. Applicability of signal processing techniques used in the linear time-invariant systems (LTIS's to the general LCSs is also discussed. Then, a criterion is proposed to determine how well a LCS can be approximated as a LTIS. In Part II, experimental validation of the analyses carried out in Part I is provided.

• 한국강구조학회 논문집
• /
• 제17권2호통권75호
• /
• pp.139-149
• /
• 2005

소성설계에 있어서 국부좌굴 후의 거동은 매우 중요한 고려사항이며, 최종 붕괴상태에 이르는 거동을 설명한다. 지진과 같은 복잡한 하중에 대하여 구조물의 실질적인 신뢰성을 얻기 위해, 국부좌굴 이후의 구조물의 점진적인 소재의 약화와 강성과 강도의 감소, 에너지 소실능력을 평가하여야 한다. 본 연구에서는, two-surface 모델에 근거하여 반복 불비례 하중에서의 국부좌굴 후 거동을 예측하기 위하여 제시된 stress resultant model을 이용하여, 단순화된 국부좌굴해석모델을 제안하였다. 이 모델을 사용한 해석적 모멘트-곡률관계는 일정한 반복 사이클 내에서 실험결과와 적절히 부합하며, 내진설계에 있어 중요한 선형 분포된 에너지 감소를 제안 모델로부터 예측할 수 있다.

• Structural Engineering and Mechanics
• /
• 제35권1호
• /
• pp.99-117
• /
• 2010

Beam-column joints are the key structural elements, which dictate the behavior of structures subjected to earthquake loading. Though large experimental work has been conducted in the past, still various issues regarding the post-yield behavior, ductility and failure modes of the joints make it a highly important research topic. This paper presents experimental results obtained for eight beam-column joints of different sizes and configuration under cyclic loads along with the analytical evaluation of their response using a simple and effective analytical procedure based on nonlinear static pushover analysis. It is shown that even the simplified analysis can predict, to a good extent, the behavior of the joints by giving the important information on both strength and ductility of the joints and can even be used for prediction of failure modes. The results for four interior and four exterior joints are presented. One confined and one unconfined joint for each configuration were tested and analyzed. The experimental and analytical results are presented in the form of load-deflection. Analytical plots are compared with envelope of experimentally obtained hysteretic loops for the joints. The behavior of various joints under cyclic loads is carefully examined and presented. It is also shown that the procedure described can be effectively utilized to analytically gather the information on behavior of joints.

• Earthquakes and Structures
• /
• 제19권4호
• /
• pp.303-313
• /
• 2020

Spacious experimental and numerical investigation has been conducted by researchers to increase the ductility and energy dissipation of concentrically braced frames. One of the most widely used strategies for increasing ductility and energy dissiption, is the use of energy-absorbing systems. In this regard, the cyclic behavior of a chevron bracing frame system equipped with multi-pipe dampers (CBF-MPD) was investigated through finite element method. The purpose of this study was to evaluate and improve the behavior of the CBF using MPDs. Three-dimensional models of the chevron brace frame were developed via nonlinear finite element method using ABAQUS software. Finite element models included the chevron brace frame and the chevron brace frame equipped with multi-pipe dampers. The chevron brace frame model was selected as the base model for comparing and evaluating the effects of multi-tube dampers. Finite element models were then analyzed under cyclic loading and nonlinear static methods. Validation of the results of the finite element method was performed against the test results. In parametric studies, the influence of the diameter parameter to the thickness (D/t) ratio of the pipe dampers was investigated. The results indicated that the shear capacity of the pipe damper has a significant influence on determining the bracing behavior. Also, the results show that the corresponding displacement with the maximum force in the CBF-MPD compared to the CBF, increased by an average of 2.72 equal. Also, the proper choice for the dimensions of the pipe dampers increased the ductility and energy absorption of the chevron brace frame.