• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.4
• /
• pp.27-33
• /
• 2001

In this study, it is observed that the distribution of combustion chamber volume affects the volumetric efficiency. The distribution ratio was adjusted by controlling combustion chamber volume of head and piston bowl one. Four cases were investigated, which are the combination of different distribution ratios and different compression ratios (9.8-10.0). A commercial SOHC 3-valve engine was modified by cutting the bottom face of the head and/or replacing the piston by the one that has different volume. The result shows that the less the head side volume, the more volumetric efficiency is achieved under the same compression ratio. It is also observed that increasing volumetric efficiency results in early knock occurrence due to increased "real" compression ratio. To consider reliability in estimating the volumetric efficiency, we examined the sensitivity of the AFR equation to possible errors in emission measurements. It is shown that the volumetric efficiency, which is calculated by measuring AFR and fuel consumption, can be controlled in 1% error. 1% error.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.42 no.5 s.305
• /
• pp.51-58
• /
• 2005

This paper proposes an efficient algorithm for extracting a tumor region from an breast ultrasound volume image by using rate-distortion (R-D) based seeded region growing. In the proposed algorithm the rate and the distortion represent the roughness of the contour and the dissimilarity of pixels in a region, respectively. Staring from an initial seed region set in each cutting plane of a volume, a pair of the seed region and one of adjacent regions whose R-D cost is minimal is searched and then they are merged into a new updated seed region. This procedure is recursively performed until the averaged R-D cost values per the number of contour pixels in the seed region becomes maxim. As a result, the final seed region has good pixel homogeneity and a much smooth contour. Finally, the tumor volume is extracted using the contours of the final seed regions in all the cutting planes. Experimental results show that the averaged error rate of the proposed method is shown to be below 4%.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.28 no.4
• /
• pp.683-693
• /
• 2001

The purpose of this study was to evaluate the effects of Er:YAG laser on cutting efficacy and its histologic findings. Dentin specimens of human premolars and molars were used and irradiated by Er:YAG laser with noncontact handpiece type delivery system under different treatment condition of irradiation time. Cavity pattern and volume were evaluated to determine the cutting efficacy and following results were obtained. 1. Cutting volume of sound dentin was getting larger with time immersed in water increase 2. With the condition of irradiation (150mJ, 10Hz, 30sec), surface irregularity was more increased in sound dentin comparing to carious dentin. For the light microscopic examination, dentinal tubules were opened and ash flecks and cracks were noted with inconsistence of dentinal tubules. 3. In case of 30 sec. irradiation in carious dentin, dark zone was limited to small focus whereas 1 min. irradiation, more wider, and cracks were noted in the perpendicular to direction of dentinal tubules. For the 2 min. irradiation, cavity was the widest and more cracks were found.

• Nuclear Engineering and Technology
• /
• v.54 no.9
• /
• pp.3242-3249
• /
• 2022

As Kori unit 1 is undergoing the decommissioning process, estimating the disposal amount of waste from the decommissioned nuclear reactor has become one of the challenging issues. Since the waste disposal amount estimation depends on the packing of the waste, it is highly desirable to optimize the waste packing plan. In this study, we developed an efficient scheme for packing waste component segments. The scheme consists of 1) preparing three-dimensional models of segments, 2) orienting each segment in such a way to minimize the bounding box volume, and 3) applying hybrid genetic algorithm to pack the segments in the disposal containers. When the packing solution converges in the algorithm, it comes up with the number of containers used and the placement of segments in each container. The scheme was applied to Kori-1 reactor pressure vessel. The required number of containers calculated by the developed scheme was 24 compared to 42 that was the estimation of the prior packing plan, resulting in disposal volume savings by more than 40%. The developed method is flexible for applications to various packing problems with waste segments from different cutting options and different sizes of containers.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.44 no.3
• /
• pp.250-256
• /
• 2008

Generally the side plate materials of FRP ship are composed of glass fiber and unsaturated polyester resin composites(GFRP composites). In this study, the effect of applied load and sliding speed on friction and wear characteristics of these materials were investigated at ambient temperature by pin-on-disc friction test. The cumulative wear volume, friction coefficient and wear rate of these materials for SiC abrasive paper were determined experimentally. The cumulative wear volume showed a tendency to increase nonlinearly with increase of sliding distance and was dependent on applied load and sliding speed for these composites. The friction coefficient of GFRP composites was increased as applied load increased at same sliding speed in wear test. It was verified by SEM photograph of worn surface that major failure mechanisms were microfracture, deformation of resin, cutting and cracking.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.7
• /
• pp.1082-1091
• /
• 2004

Analyzed Parametrically was an internal combustion engine combined with gas turbine the cycle of which is splitted into compression side cylinder and expansion side one, and heat adding of which is during constant volume pressure, temperature process. The advantages of each measures were analyzed by means of thermal cycle diagram. The thermal efficiency of partial load cutting off firstly isothermal heat adding and secondly isobaric heat adding also was analyzed The authors suggested some potentials about the performance as for thermal efficiency, mean effective pressure and reducing emissions and noise supposed were the operating parameter of the engine set to some values and were some problems solved.

• Journal of the Korean Society of Costume
• /
• v.25
• /
• pp.215-231
• /
• 1995

Semiotics is an external expression for show-ing internal meaning, and the signs express the internal meaning. The architects and the designers are very similar each other in using semiotics for expressing their desires. Histori-cally, the design similarity exists between the architecture and the fashion. In this study, the fashion designs are interpreted by using semiotics of architectural design, especially emphasizing external expression methods for representing internal desires. To express the human body's character-istics, the volume, weight support, structural simplicity, controllability and beauty of fashion were used for the fashion designs, and those characters could be found at the architec-tural patterns. Balenciaga's fashion emphasized the volume, the weigh support, the structural simplicity and the controllability, while Roberto Capucci rejected the approach of using women's body curves, but used the volume and simplicity of natures in addition to Balenciaga's heavy weight design patterns. The control and the modern dedication were used to make the simple patterns by Courreges, and then brought the Modernism to the fashion. Courreges used the cutting characters to func-tional design for expressing the structural sim-plicity.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1126-1129
• /
• 2004

Because of the various length condition of carbon nanotube, it is very confined the application area of the single CNT tip. In this paper, it was proposed the cutting technique of single CNT tip and the relationship between the etched volume and the amount of the applied charge. It is possible to control the length of single CNT tip arbitrary using this technique. The etched volume and length in the single CNT tip can be predicted with the amount of the applied charge. It is very easy to make a single CNT tip with proper length using this technique and to make nanotweezer that was composed two single CNT tips.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.24 no.2
• /
• pp.153-170
• /
• 2022

Waterjet has been comprehensively used in urban areas owing to a suitable technique for cutting concrete and rock, and low noise and vibration. Recently, the abrasive waterjet technique has been adopted and applied by the Korea Atomic Energy Research Institute to demolish concrete plugging without disturbing and damaging In-situ Demonstration of Engineered Barrier System in the disposal research tunnel. In this study, the use of abrasive waterjet in the tunnel was evaluated for practical applicability and the existing cutting model was compared with the experimental results. As a variable for waterjet cutting, multi-cutting, water flow rate, abrasive flow rate, and standoff distance were selected for the diversity of analysis. As regarding the practical application, the waterjet facilitated path selection for cutting the concrete plugging and prevented additional disturbances in the periphery. The pump's noise at idling was 64.9 dB which is satisfied with the noise regulatory standard, but it exceeded the standard at ejection to air and target concrete because the experiment was performed in the tunnel space. The experimental result showed that the error between the predicted and measured cutting volume was 12~13% for the first cut and 16% for second cut. The standoff distance had a significant influence on the cutting depth and width, and the error tended to decrease with decrement of standoff distance.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.22 no.4
• /
• pp.339-347
• /
• 2004

This study aims at calculating the exact soil conversion factor of cutting and banking areas of weathering rocks in large-scaled construction sites where land is being developed into home lots. For this, we have excavated the respective 20 sites of the cutting and banking areas in the said site and then calculated the volume after the excavation. As a result, the relative accuracy of the difference was calculated at 0.5% in average. We have calculated the exact soil conversion factor by the use of function ratio as per the wet unit weight and the indoor soil quality test as per volume calculated. And then we have found out minor differences as a result of the comparison and analysis with soil conversion factor determined by the dry unit weight test as per sand replacement method. This may be judged as a rational design method for the calculation of soil conversion factor, as well as high reliability of site test as a precision photogrammetry is adopted for volume measurement of the irregular excavating areas.