• 한국정밀공학회지
• /
• 제33권1호
• /
• pp.11-16
• /
• 2016

Lithography techniques are generally used to manufacture nano-patterns on silicon, however, it is difficult to make a V-shaped pattern using these techniques. Although silicon is a brittle material, it can be treated as a ductile material if mechanically machined at extremely low force scale. The manufacturing technique of nano-patterns on single crystal silicon using a mechanical method was developed in this study. First, the linear pattern was machined on the silicon with increasing thrust force. Then, the correlation between measured cutting force and machined pattern was analyzed. Based on the analysis, the critical thrust force was quantitatively determined, and then the silicon was machined at a force lower than the critical thrust force. The machined pattern was observed using SEM and AFM to check for the occurrence of brittle fractures. Finally, the sharp V-shaped nano-pattern was manufactured on the single crystal silicon.

• 한국공간구조학회:학술대회논문집
• /
• 한국공간구조학회 2006년도 춘계 학술발표회 논문집 제3권1호(통권3호)
• /
• pp.214-223
• /
• 2006

Membrane structures, a kind of lightweight soft structural system, are used for spatial structures. The material property of the membrane has strong axial stiffness, but little bending stiffness. The design procedure of membrane structures are needed to do shape finding, stress-deformation analysis and cutting pattern generation. In shape finding, membrane structures are unstable structures initially. These soft structures need to be introduced initial stresses because of its initial unstable state, and happen large deformation phenomenon. Therefore, in this study, to find the structural shape after large deformation caused by initial stress, we need the shape analysis considering geometric nonlinear term. And we investigate the evaluation of shape analysis technique's convergence and efficiency according to the control method

• 한국의류학회지
• /
• 제31권5호
• /
• pp.692-704
• /
• 2007

Recently, Basic patterns with excellent body fitness and automation availability are required to be developed in order to automate the patterns of women's clothes. In this study, this reference points, reference lines and segments were fixed onto 3D scan data for the lower body the women in their twenties, they were directly spread out to be 2D flat pattern to facilitate development into the design of slacks adhered closely to the human body such as special and highly-functional clothes, and then slacks 2D pattern was developed for the purpose of seeking scientific approach to the development into basic form slacks and 3d emotional pattern. For conversion of 3D pattern into 2D flat pattern, reference points and segments were created by using Rapid Form of 3D shape analysis software, and triangle mesh of the body surface of the created shape was developed with Auto CAD 2005. The correspondence between slacks and human body was examined by the fixation of major reference lines. Specially, the wearing characteristics of slacks were considered by the fixation of side lines in consideration of posture. As a result of using the way of development to constantly maintain the length while 3D triangle mesh is converted into 2D flat mesh, the shape was shown to be excellently reproduced, and the area of flat pattern was increased compared to the shape of parting plane. Also, the sunk-in curve like the brief line of front crotch length needed a cutting line when it was closely adhered, when mesh was overlapped, and the pattern area was smaller compared to the actual shape.

• 복식
• /
• 제56권7호
• /
• pp.68-84
• /
• 2006

The aim of this study is to examine a structure of trousers worn by males in the western world during the 17th and 18th centuries in order to understand the characteristics of evolution in construction. it mainly examined engravings from these era because they provided me fine and detailed portrayals of what it needed to observe. Then, it classified them into models according to each era. it supplemented a flaw of depending on single type of studying material by examining other types of historical materials such as historical paintings and documents for comparative analysis of materials and decorations and previous studies on preserved historical documents to observe the examples of structures of trousers. Secondly, it studied both historical documents and previous studies on the trousers patterns used back in those days, analyzed the characteristics of each designing method by actually draping these patterns, and observed the differences in these completed patterns to understand the characteristics of changes in fashion design skill. As for the changes in length, these patterns show only a slight difference around above and below the knee line. However, the widths of waist, hip, girth and hem were significantly altered over the years to reduce wrinkles and the cutting lines became more refined to make the clothes fit to the body. As a result, a simple but fine patterning technique was born. In particular, new methods in cutting and sewing were invented for detailed parts such as waist, pocket, front and slit.

• 산업경영시스템학회지
• /
• 제43권4호
• /
• pp.161-167
• /
• 2020

In the process of cutting large aircraft parts, the tool may be abnormally worn or damaged due to various factors such as mechanical vibration, disturbances such as chips, and physical properties of the workpiece, which may result in deterioration of the surface quality of the workpiece. Because workpieces used for large aircrafts parts are expensive and require strict processing quality, a maintenance plan is required to minimize the deterioration of the workpiece quality that can be caused by unexpected abnormalities of the tool and take maintenance measures at an earlier stage that does not adversely affect the machining. In this paper, we propose a method to indirectly monitor the tool condition that can affect the machining quality of large aircraft parts through real-time monitoring of the current signal applied to the spindle motor during machining by comparing whether the monitored current shows an abnormal pattern during actual machining by using this as a reference pattern. First, 30 types of tools are used for machining large aircraft parts, and three tools with relatively frequent breakages among these tools were selected as monitoring targets by reflecting the opinions of processing experts in the field. Second, when creating the CNC machining program, the M code, which is a CNC auxiliary function, is inserted at the starting and ending positions of the tool to be monitored using the editing tool, so that monitoring start and end times can be notified. Third, the monitoring program was run with the M code signal notified from the CNC controller by using the DAQ (Data Acquisition) device, and the machine learning algorithms for detecting abnormality of the current signal received in real time could be used to determine whether there was an abnormality. Fourth, through the implementation of the prototype system, the feasibility of the method proposed in this paper was shown and verified through an actual example.

• 한국안광학회지
• /
• 제18권3호
• /
• pp.231-239
• /
• 2013

목적: 안경테의 형판제작을 위한 자동취형기 개발을 위해 설계하고 제작하고자 한다. 방법: 자동취형기의 주요 설계도를 캐드로 그려서 제작에 필요한 정보를 얻었다. 이 데이터를 기본으로 자동취형기 개발을 위해 시제품을 제작하였다. 결과: 자동취형기는 형판가공부, 조작판넬, 안경테장착부, 탐침자부로 구성되었다. 형판가공부는 절삭부, 플라스틱 형판 고정부, 형판 이탈핀 그리고 형판 절삭시 소음을 최소화시키기 위한 방음덮개로 구성하였다. 조작판넬은 메인 P.C.B.와 서로 연결 및 작동되게 설계하였다. 탐침자가 $1.8^{\circ}$ 각도로 안경테 삽입부를 스캐닝해서 얻은 좌표값에 대한 엔코딩한 값을 통해 삽입부의 정보를 얻게 되었다. 스캐닝이 시작된 후에는 오른쪽 방향과 왼쪽방향으로 작동된다. 통신연결부는 RS232C 전송방식으로 자동취형기에서 외부 장치로 안경테 렌즈삽입부의 정보를 전송하여 형판 없이도 안경렌즈를 가공할 수 있었다. 형판의 절삭치수의 오차율을 평가하기 위해 일원배치분산분석한 결과 F값과 P값은 0.510과 0.601로 나와서, 자동 취형기에서 가공된 형판의 ${\Phi}22mm$, ${\Phi}55mm$ 그리고 ${\Phi}62mm$ 절삭 치수의 오차율은 크기에 따라 차이가 없는 것으로 나타났다. 또한, 개발된 자동취형기의 평균 절삭 오차값은 0.0274 mm으로 나타났다. 결론: 자동취형기를 설계 및 제작하여 시제품 제작에 성공하였다. 자동취형기의 역할은 안경테를 측정하여 안경테에 맞는 정확한 렌즈삽입부의 크기를 얻는 것이다. 자동취형기로부터 얻어진 정보값은 외부장치로 보내져 형판 없이 안경렌즈를 연삭가공 한다. 또한, 시제품은 안경테에 맞는 형판을 만들 수 있다. 연구개발 된 시제품을 통해 안경사들이 편리하게 형판제작이 가능하고, 과거 보다 안경 조제가공이 보다 효율적이게 작업이 이루어질 수 있을 것으로 예상된다.

• 복식
• /
• 제59권8호
• /
• pp.49-65
• /
• 2009

As basic materials in this research, 874 pieces of engraving that recorded the garment produced by diverse authors in the 17-18th century were collected among the collections of male and female garment in the engraving kept by National Library of France and 216 pieces of engraving were classified among them to observe justaucorps as stated in the materials. Since type of justaucorps in the 18th century can be classified by difference in shape and change through the above engraving materials in large quantity and the shape and composition can be compared and analyzed with other materials such as picture, stored garment, written materials without difficulty, the chronology can be composed by single type of justaucorps. Intending to understand the change in composition caused by type classification and pattern making as per analysis of type property of justaucorps, the men's upper garment in France in the 18th century. Checking change in design per from and materials, justaucorps of 1680-1700s was in silhouette where waist in the length above knee was adhered and slightly spread to lower part. In the type of 1710-1750s, waist adhered remarkably and many pleats were made under waist to produce volume of form that spread to lower part like skirt. In the type of 1760-1780s, straight silhouette was attached to whole body and end of front adjustment in slant line turns to rear part. The developmental aspect of construction can be checked by making pattern. Changing the cutting line of body plate to smoothly connect section and to try to adhere to the body, the development of simpler and delicate pattern production technique was confirmed.

• 소성∙가공
• /
• 제22권8호
• /
• pp.437-441
• /
• 2013

Recently, the engraving of letters or a pattern on a product surface has received more attention especially in trying to satisfy the customer requirements. Half-piecing is a protrusion forming process that pierces only 40~50% of the material thickness. In the current study, the half-piercing technique for making clear letters by protruding sheet material was selected and studied. The influence of clearance and penetration depth was investigated by measuring the camber and extruded length of a protrusion after experiments. In addition, a numerical analysis was performed for the same working conditions and compared with experimental results. It is shown that, as the clearance increases, the camber of a protrusion increases rapidly and the extruded length decreases slightly. The deformation pattern around the cutting edge during half-piercing changes from an extrusion mode to a shearing mode as the clearance changes from minus to plus values. It is also confirmed that the experimental results show a good agreement with the numerical analyses.

• 한국생활과학회지
• /
• 제21권3호
• /
• pp.551-565
• /
• 2012

The primary goal of this study was to provide a systematic methodology of utilizing 3D technology for tight-fit performance sportswear using information of skin deformation in various posture. Technical tools used in this study are Cyberware whole body scanner, RapidForm2004, 2C-AN 3D pattern development program, and YukaCAD. Analysis of the 3D skin deformation while knee joint was bent from $0^{\circ}$ to $60^{\circ}$ revealed that the length of dermatomes L4 was remained consistent during knee bending. Therefore, L4 was chosen as a major cutting line. To develop a highly ergonomic pattern, replicas of static and dynamic postures were developed and integrated using two methods, one is morphing method (Sqirlz Morph), and the other is AutoCAD. Experimental tight-fit garments called 'Derm-Mov Pattern' was designed using dematomes L4, L2, and inner line under knee and compared with four other patterns. As results, AutoCAD was appropriate as a integrating method of various postures. In wear test, 'Derm-Mov Pattern' was rated high (p < .001), in terms of pressure comfort especially around front crotch area. However, wear sensation was not signipicantly different in other area due to highly extensible property of materials. Pressure distribution was relatively even in these experimental garments.

• 한국의상디자인학회지
• /
• 제20권4호
• /
• pp.95-104
• /
• 2018

This study classified the figurative features of the raglan sleeves presented in the Spring and Summer Collections and Fall and Winter Collections abroad in 2010 and 2018 and analyzed the production methods and patterns of the classified raglan sleeves. The analysis results are described below. The raglan sleeves in the latest fashion trends were classified into Type H, Type A, Type O and Type Y per shape. The production features of raglan sleeves in the latest fashion trends included the cutting lines in various shapes, a flounce that made shoulders look wider, and decorations such as gathers, studs, punching, slits, pleats and tucks. The raglan sleeve design was classified into Yoke Raglan, Armhole Princess Raglan, Semi Raglan, Gathered Raglan, Pleats Raglan, Cowl Raglan, Origami Raglan, Circular Curved Raglan, Capes Raglan and Constructive Design Raglan and the patterns per design were presented. For creative and experimental clothing by the analysis of the features of raglan sleeve structure, a variety of configuration methods need to be developed and implemented. The analysis results of this study will contribute to the development of the fashion industry through small quantity batch production pursuing unique styles as the basis for further study on the configuration methods of raglan sleeves. This study will be used in various ways as education materials on sleeve patterns in the educational field. Through the analysis of sleeve patterns, this study tries to provide basic data for planning the design of raglan sleeves and helping to diversify the ladies' apparel market in the future.