• Journal of the Korean GEO-environmental Society
• /
• v.6 no.2
• /
• pp.15-20
• /
• 2005

Moutain side ditch is constructed at the top of cutting slopes around road and it drains the surface water that flowed from upper part. About 70% of a country is composed of mountains so occurrence of cutting face by road general observation is necessary. Instability of cutting face is increased by permeation of underground water by rainfall the summer, pore water pressure increases. However, moutain side ditch is constructed on the top of cutting slopes has some troubles. For example, difficulty of qualify control and lack of drainage faculty. Therefore, stability variation of cutting slope is analyzed by hydraulic conductivity and construction depth of mountain side ditch and effective depth of mountain side ditch is decided in this paper.

• Journal of Advanced Engineering and Technology
• /
• v.11 no.4
• /
• pp.227-235
• /
• 2018

Studies on the laser cutting processing characteristics of magnesium alloys can be divided into three parts, comparing the cutting faces of magnesium alloy and aluminum alloy, observing the shape of the corner where straight lines meet, and observing the straight lines and arcs. First, there were no laser cutting conditions for magnesium alloys, so it was observed to cut magnesium alloy and aluminum alloy under the same processing conditions as aluminum alloy to shape and surface of the cut surface. Next, to observe the characteristics of the corner, we observed the shape of the corner according to the angle change of the part where the two lines meet, and finally we observed various angles to observe the characteristics of the part where the arc meets the line. Finally, laser cutting processing characteristics of magnesium alloys and aluminum alloys obtained based on the above study contents were summarized.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.17 no.4
• /
• pp.365-374
• /
• 2004

Steel bridges, which have been damaged by load and corrosion, need repair or strengthening. That is a cause of decreasing the durability of structure. In order to solve these problems, welding repair and strengthening methods can be considered. In general, cutting and welding procedure is carried out during the repair welding. Therefore, the investigation of the behavior of residual stress and deformation generated by cutting and welding is very important for safety of structure. Residual stress and deformation produced by gas cutting and arc welding were analyzed using 2D and 3D thermal elasto-plastic FEM. According to the results, the magnitude of temperature was analyzed by 2D-FEM is smaller than that was analyzed using the 3D-FEM at the start and end edge of flange. And the magnitude and distribution of residual stress of perpendicular direction of the cutting line and welding line was analyzed by the 2D-FEM was similar to that was analyzed by 3D-FEM. Therefore, it is possible to predict cutting and welding residual stress by 2D and 3D FEM.

• Proceedings of the IEEK Conference
• /
• 2002.07a
• /
• pp.168-171
• /
• 2002

For laser-cutting rapid prototyping systems that fabricate objects with layers having a certain degree of thickness, it is necessary both to minimize surface distortion and to generate dynamically feasible laser cutting trajectories. An effective tangential layer cutting algorithm is developed for this requirements. An energy function is defined in terms of tangential line lengths and their distances. And the energy is minimized for the tangential lines to closely describe a layer suffice. Our method is applied to 3D model samples and the generated tangential lines effectively approximate layer surface and make laser trajectory smooth.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.15 no.1
• /
• pp.32-38
• /
• 2006

The magnetic fluid polishing technique can polish the tool of complex shape, because the polishing method which polishes as compress the workpiece by the magnetism abrasives to arrange to the linear according to the line of magnetic force. Therefore, we producted the magnetic fluid polishing device in order that mirror like finishing processes the tool surface. In order to a polishing condition selection, polishing characteristic was estimated by polishing conditions which are magnetic flux density, polishing speed, grain size, magnetic fluid. The tool was polished to the selected polishing condition. The result to evaluate the polished tool's performance with the cutting force and tool wear, the polished tool's performance was improved compared with the tool not to polish.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.321-327
• /
• 1993

In order to maintain the cutting force at a desired level during peripheral end milling processes in spite of variation of the depth of cut and other machining conditions, a feedrate override. Apaptive Control Constraint (ACC) system are developed. Feedrate override was accomplished by a developed MMC board and PMC interface techniques. Nonlinear model of the cutting process was linearized as an adaptive model with time varying paramrters. Integral type estimators were introduced for on-line identification of cutting and control parameters in peripheral and milling processes. Zero Order Jold (ZOH) type degital control methodology which uses pole-placement concepts was applied for the ACC system. Performance of the developed ACC system was confirmed on the vertical machining center equipped with FANUC OMC for a large amount of experiment

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.963-966
• /
• 2000

Abrasive jet machining(AJM) process is similar to the sand blasting, and effectively removes hard and brittle materials. AJM has applied to rough working such as deburring and rough finishing. As the needs for machining of ceramics, semiconductor, electronic devices and LCD are increasing, micro AJM was developed, and became the inevitable technique to micromachining. This paper describes the performance of the micro AJM in micro groove cutting of glass. Diameter of hole and width of line in this groove cutting is 80${\mu}{\textrm}{m}$. Experimental results showed good performance in micro groove cutting in glass, but the size of machined groove was increased about 2~4${\mu}{\textrm}{m}$. therefore, this micro AJM could be effectively applied to the micro machining of semiconductor, electronic devices and LCD parts.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.10a
• /
• pp.344-348
• /
• 1992

This paper presents a new methodology for on-line tool breakage detection by sensor fusion concept of an acoustic-emission (AE) sensor. A built-in piezoelectric force sensor was used to measure cutting force instead of a tool dynamometer to preserve the machine tool dynamics. he sensor was inserted in the tool turret housing of an NC lathe. FEM analysis was carried out to locate the most sensitive position for the sensor. When a tool is broken, the explicit changes of signals' pattern take place. A burst-type AE signal increases abruptly. Followingly, a cutting force drops significantly. Therefore a burst of AE signal is used as a triggering signal to inspect the following cutting force. Significant drop of cutting force is utilized to detect tool breakage. The algorithm was implemented in a DSP board for in-process tool breakage detection. The proposed monitoring system was capable of a good applicable tool breakage detection.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.806-812
• /
• 2008

Many kinds of rolling-stocks that have various control methods are being operated by Seoulmetro which is a history of a city railroad rolling-stock. Seoulmetro is being faced with a wheel management comparing of other lines with a perpendicular wear of wheel and a side damage, and so on, by operating several cars at a loop line. This is causing maintenance expenses increase and deteriorating a fusibility of rolling-stock, for it has an effect on a rolling-stock using. A cutting pattern of wheel and a wear form affect the expected span of a wheel. A wheel cutting cause is classifed into cutting for reprofiling of a flange wear of wheel and for removing every kind defect which originates from wheel wear. In this study, Seoulmetro exhibit a stable rolling-stock use method and a reasonable management method of wheel, analysing wheel exchange condition and cutting management of wheel.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.3
• /
• pp.130-143
• /
• 1995

This paper presents a new methodology for on-line tool breadage detection by sensor fusion of an acoustic emission (AE) sensor and a built-in force sensor. A built-in piezoelectric force sensor, instead of a tool dynamometer, was used to measure the cutting force without altering the machine tool dynamics. The sensor was inserted in the tool turret housing of an NC lathe. FEM analysis was carried out to locate the most sensitive position for the sensor. A burst of AE signal was used as a triggering signal to inspect the cutting force. A sighificant drop of cutting force was utilized to detect tool breakage. The algorithm was implemented on a DSP board for in-process tool breakage detection. Experiental works showed an excellent monitoring capability of the proposed tool breakage detection system.