• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 추계학술대회 논문집 학회본부
• /
• pp.84-87
• /
• 1996

This paper presents a energy function to reflect the control effect of speed governor which has a cut-off property which means position and rate limit The proposed energy function satisfies the semi-negativeness of its time derivative and well reflects the parameters of speed governor to the energy function. The transient stability analysis by the direct method for the single machine infinite bus system has been conducted with the use of the proposed energy function, which shows that the results by the direct method well agree with that by the conventional time simulation method. This thesis shows a possibility of more accurate stability analysis by taking into account the cut-off property of speed governor's output.

• 한국산학기술학회논문지
• /
• 제13권2호
• /
• pp.498-503
• /
• 2012

엔진 회전속도가 1,500rpm 이상 일 때 차량의 가속 페달을 놓은 경우 인젝터 연료분사가 중지된다. 이것을 연료차단(fuel-cut) 기능이라 부르고, 현대의 대부분의 차량들은 이 기능을 장착하고 있다. 이 기능은 많은 경우 고속도로의 내리막 구간에서 작동된다. 이렇게 연료차단이 발생하는 경우 차량의 $CO_2$ 배출 가스는 '0'이 된다. 서해안 고속도로에서 이 연료 차단 기능을 사용하면 2,000cc 승용차의 $CO_2$ 배출량은 4% 감소한다. 그리고 내리막 구간의 경우 가장 효율적인 운전 패턴을 찾기 위하여 연료차단 기능을 AVL사의 CRUISE 소프트웨어로 시뮬레이션 하였다. 연비향상을 위해서 급격한 내리막 구간일 경우 연료 차단을 위한 차량의 하한 속도를 높게 유지해야 한다는 것을 CRUISE 소프트웨어 시뮬레이션으로 알 수 있었다. 또한 가장 우수한 연비 성능은 내리막 구간 내에서 연료차단과 재가속이 완료되어야 함을 알 수 있었다.

• 한국자동차공학회논문집
• /
• 제18권1호
• /
• pp.86-92
• /
• 2010

The fuel is not injected when the driver doesn't push acceleration pedal of a vehicle with engine speed higher than about 1,500rpm above mid vehicle speed range. This is called "fuel-cut function" and almost every modern vehicle is equipped with this function. This is activated on downhill part of a highway most often. Therefore the vehicle-exhausted $CO_2$ can be zero in this downhill part if the driver could recognize this part of highway. We compared the vehicle-exhausted $CO_2$ emission when using fuel-cut function with the $CO_2$ mass when without using this function in this study. We found that the $CO_2$ emission reduced with fuel-cut function and measured the reduction rate of vehicle-exhausted $CO_2$ mass with this test results. The exhausted $CO_2$ mass of a passenger car(2,000cc engine volume) is reduced by 4% with this function used. This $CO_2$ reduction effect can be achieved if the downhill part of a highway is painted with a specific color. And this road painting can be included in the highway road rehabilitation policy.

• 한국CDE학회논문집
• /
• 제6권3호
• /
• pp.206-214
• /
• 2001

This paper describes the wire EDM (Electric Discharge Machining) CAM system considering a variable taper wire-cut and an unmanned wire EDM during the night. Wire EDM is applicable to all materials that are fairly good electrical conductors, including metals, alloys and most carbide. Thus it provides a relatively simple method for making holes of any desired cross section in materials that are too hard or brittle to be machined by most other methods. In this paper we classify variable taper wire-cut machining patterns and variable taper wire-cut geometries. Also we determine unmanned wire EDM patterns fur the productivity of wire EDM industry. Developed system consists of two modules: 1) Variable taper wire EDM module guarantees the length ratio machining function, the parametric ratio machining function and the marking function. 2) Unmanned wire EDM module guarantees the automatic wire EDM during the night. The proposed system has been tested in the fields and found to be a useful system.

• 한국수학교육학회지시리즈B:순수및응용수학
• /
• 제26권3호
• /
• pp.199-208
• /
• 2019

A necessary and sufficient condition in terms of lower cut sets is given for the insertion of a Baire-.5 function between two comparable real-valued functions on the topological spaces that whose $F_{\sigma}$-kernel of sets are $F_{\sigma}$-sets.

• 한국수학교육학회지시리즈B:순수및응용수학
• /
• 제26권1호
• /
• pp.1-12
• /
• 2019

Necessary and sufficient conditions in terms of lower cut sets are given for the strong insertion of a Baire-.5 function between two comparable real-valued functions on the topological spaces that $F_{\sigma}-kernel$ of sets are $F_{\sigma}-sets$.

• 대한수학회논문집
• /
• 제31권1호
• /
• pp.27-40
• /
• 2016

We define the notion of a residuated lattice valued function on a set as Jun and Song have done in BCK-algebras. We also investigate related properties of residuated lattice valued function. We establish the codes generated by residuated lattice valued function and conversely we give residuated lattice valued function and residuated lattice obtained by the giving binary block-code.

• 대한토목학회논문집
• /
• 제12권4_1호
• /
• pp.129-136
• /
• 1992

압력식(壓力式) 파고계(波高計)에서 측정(測定)되어진 압력파형(壓力波形)으로부터 수위변동(水位變動)을 추정(推定)하는 방법(方法)에 대해서 1) Fast Fourier Transform Method(FFTM), 2) Local Curvature Method(LCM), 3) Individual Wave Method(IWM)의 3가지 방법(方法)을 비교(比較)하여, 천해역(淺海域)에 있어서의 파랑측정(波浪測定)에 대한 압력식(壓力式) 파고계(波高計)의 적용성(適用性)에 대해 검토(檢討)했다. 그 결과(結果) 다음과 같은 결론(結論)을 얻었다. 1) 측정(測定)되어진 압력파형(壓力波形)으로부터 수위변동(水位變動)을 추정(推定)할 때에 사용(使用)되어지는 이론선형응답함수(理論線形應答函數)(Hp=coshkh/coshk(h+z)의 적용가능범위(適用可能範圍)(cut-off-frequency)는 $kh{\leq}3.0$이다. 그리고 kh > 3.0의 영역(領域)에 있어서의 이론선형응답함수(理論線形應答函數)는 일정치(一定値)를 부여함으로써 매우 정도높은 수위변동(水位變動)을 얻을 수 있다. 2) LCM에 의한 수위변동(水位變動)의 변환(變換)에 있어서는 측정(測定)된 압력파형(壓力波形)속에 포함되어 있는 단주기파(短週期波)들에 의해 크게 영향(影響)을 받는다. 그러므로, kh > 1.5인 영역(領域)의 압력변동(壓力變動)을 무시할 필요(必要)가 있다. 3) FFTM 및 IWM에 의해 추정(推定)되어진 통계량(統計量)의 재현성(再現性)은 양호하고, 특(特)히 평균주기(平均週期)의 재현성(再現性)으로부터 비선형성(非線型性)이 강한 영역(領域)에 있어서는 IWM이 유효(有效)한 수단이라고 사려되어진다.

• 한국생산제조학회지
• /
• 제5권3호
• /
• pp.58-65
• /
• 1996

This thesis is concerned with the study on the characteristics of the cutting resistance occurring in finish machining of hardened steels such as carbon tool steel and alloy tool steel by a ceramic tool with nose radius. For the purpose, the shape of cutting cross-section made at nose part of the tool was analyzed geometrically and the wear mechanism on the flank face of the ceramic tool is investigated. In order to investigate the characteristics of cutting resistance two categories of cutting conditions are suggested, along with geometrical analysis. One category includes the conventional cutting parameters such as feed and depth of cut, another containing new cutting parameters of thickness of cut and width of cut etc. Thickness of cut width of cut and area of undeformed chip section formed by the condition of engagement between workpiece and cutting tool are determined as the function of feed, depth of cut and nose radius of cutting too, And an effective approach angle is determined by depth of cut and nose radius.

• 한국소음진동공학회논문집
• /
• 제21권5호
• /
• pp.447-454
• /
• 2011

This paper reports a filtered velocity feedback(FVF) controller, which is an alternative to direct velocity feedback(DVFB) controller. The instability problems due to high frequency response under DVFB can be alleviated by the suggested FVF controller. The FVF controller is designed to filter out the unstable high frequency response. The FVF controller and the dynamics of clamped beams under forces and moments are first formulated. The effects of the design parameters(cut-off frequency, gain, and damping ratio) on the stability and the performance are then investigated. The cut-off frequency should be selected not to affect the system stability. The magnitude of the open loop transfer function(OLTF) at the cut-off frequency should be small. As increasing the gain of the FVF controller, the magnitude of the OLTF is increased, so that the closed loop response can be reduced more. The enhancement of the OLTF at the cut-off frequency is reduced but the phase behavior around the cut-off frequency is distorted, as the damping ratio is increased. The control performance is finally estimated for the clamped beam. More than 10 dB reductions in velocity response can be achieved at the modal frequencies from the first to eighth modes.