• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.11a
• /
• pp.71-72
• /
• 2014

Green Frame is a building frame system to construct a column-beam structure using composite precast concrete members. To reduce the cost of producing precast concrete, in-situ production of members is required. However, when the structural members are produced on site, it needs a large space for production. So, "Just-In-Time" production method should be adopted. For Just-In-Time to be realized, the early strength of members should be ensured for them to be transported. Thus, steam curing to secure the early strength is applied in Green Frame. Yet, a large-scale steam curing system is not possible for in-situ production of precast concrete. A smaller steam curing system is needed. In this regard, the study is aimed to develop a new steam curing method applicable to the in-situ production of precast concrete.

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.4
• /
• pp.51-56
• /
• 2014

After the preparation of low-cost conductive paste containing Ag-coated Cu flakes, thermal conductivity and electrical resistivity of the paste were measured with different curing conditions. Under air-curing conditions, the thermal conductivity of the cured sample increased with an increase of curing time from 30 to 60 min. After identical curing time of 60 min, the sample cured under nitrogen indicated more enhanced thermal conductivity than that cured under air, approaching that of paste containing pure Ag flakes. Under air-curing conditions, meanwhile, the electrical resistivity of the cured sample increased with an increase of curing time from 30 to 60 min. After identical curing time of 60 min, however, the sample cured under nitrogen indicated extremely enhanced electrical resistivity ($7.59{\times}10^{-5}{\Omega}{\cdot}cm$) in comparison with that cured under air.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.553-556
• /
• 2003

This study is analyzed about the factor of adhesive strength characteristics, curing time, asphalt application, test temperature which are liquid waterproofing membrane of rubber-asphalt and chloroprene-rubber type for concrete bridge deck. According to the results, curing time is shorter, adhesive strength is less in chloroprene-rubber type. And also chloroprene-rubber and rubber-asphalt type are showed high adhesive strength in low temperature.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.53 no.5
• /
• pp.25-33
• /
• 2011

In this paper, the effects of aggregate and curing temperature on strength development characteristics of UP (Unsaturated Polyester)-MMA (Methyl Methacrylate) based polymer mortar under sub-zero temperature are experimentally investigated to provide a criterion for repair and production of precast products. The result showed that the setting time of the binder was 4 minutes at $20^{\circ}C$ whereas 35 minutes at $-20^{\circ}C$. The result also revealed that the compressive, flexural, and splitting tensile strengths of UP-MMA based polymer mortar significantly decreased as the aggregate and curing temperatures decreased. However, sufficient strengths which can be implemented in actual practices -36.6 MPa of compressive strength, 6.11 MPa of flexural strength, and 5.81 MPa of splitting tensile strength - were obtained even though both aggregate and curing temperatures were $-20^{\circ}C$. Strength development of polymer mortar is largely affected by curing temperature rather than aggregate temperature. It was found that the effects of aggregate temperature on strength development become smaller as the curing temperature becomes lower. Also, toughness, a ratio of compressive strength to flexural strength, increased from 3.5 to 5.9 as both aggregate and curing temperatures decreased from $20^{\circ}C$ to $-20^{\circ}C$.

• International Journal of Concrete Structures and Materials
• /
• v.9 no.4
• /
• pp.487-498
• /
• 2015

A proper initial curing is a very simple and inexpensive alternative to improve concrete cover quality and accordingly extend the service life of reinforced concrete structures exposed to aggressive species. A current study investigates the effect of wet curing duration on chloride penetration in plain and blended cement concretes which subjected to tidal exposure condition in south of Iran for 5 years. The results show that wet curing extension preserves concrete against high rate of chloride penetration at early ages and decreases the difference between initial and long-term diffusion coefficients due to improvement of concrete cover quality. But, as the length of exposure period to marine environment increased the effects of initial wet curing became less pronounced. Furthermore, a relationship is developed between wet curing time and diffusion coefficient at early ages and the effect of curing length on time-to-corrosion initiation of concrete is addressed.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.2
• /
• pp.465-470
• /
• 2015

The curing of epoxy asphalt mixture depends on the chemical reaction of epoxy resin and the curing agent. The curing level of epoxy asphalt mixture needs to be predicted in order to decide traffic opening time and to establish further construction plans. In this study, chemical analysis of the prediction model was executed to expand the applicability of the previous prediction model. Consequently, the curing level prediction model of epoxy asphalt concrete mixture was proposed using the concentration ratio and the acid value ratio. According to the results of outdoor curing experiments, the final prediction model showed that the correlation coefficient is greater than 0.971. Precise prediction results of different composition epoxy asphalt were obtained by reflecting the chemical composition ratios in the curing level prediction model.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.4
• /
• pp.16-21
• /
• 2002

It was observed that drying temperature and curing time in the paper coating process as well as Tg of the latex used as a binder, greatly affected the properties of the coated paper such as roughness, paper and print gloss, K & N ink drop, and ink set-off. The higher drying temperature induced faster water evaporation and change in binding density, which caused an increase in paper roughness, ink gloss and ink set-off, but decrease in paper gloss and K & N ink drop. The increased curing time promoted latex filming and redistribution of the binder in coating layer. This increased pick strength and ink gloss, but decreased ink trapping. Finally, the higher Tg of the latex showed the wider changing range of these properties.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.05a
• /
• pp.260-263
• /
• 1996

The thermally stimulated currents(TSC) are measured to know the behaviour of charging particles of epoxy composites at the temperature range of -160∼200[$^{\circ}C$] and to prove the variation according to curing time in this study. It is confirmed that the peak amplitude is inversely proportional to the curing time, and TSC are reduced is and T$\sub$m/ is moved to high temperature side according to the curing time because carboxyl radical is formed by thermal oxidation and motility becomes lack.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.4
• /
• pp.24-32
• /
• 2008

We made a new propellant formulation to improve the productivity of Base Bleed Unit(aka BBU) by reducing of the curing time. We made an experiment with new propellant formulation such as binder characteristics and manufacturing process. In addition, we already tested several basic characteristics and the final performance of the new propellant. According to the test report, it was not only satisfied with all requirements in the specification, but it also contributed to improve productivity and reduced 53% of the curing time.

• Journal of Adhesion and Interface
• /
• v.13 no.2
• /
• pp.85-88
• /
• 2012

In this paper, the curing reaction of UF resins was investigated by a real time FT-IR method. The curing temperature range of the UF resin was $25{\sim}200^{\circ}C$. It was found that the reactions of UF resin at different temperatures resultedin resins with different cross-linked structures. A real time FT-IR spectroscopy can be considered as a good routine analytical tool for following the progress of UF resin curing.