• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.6
• /
• pp.113-118
• /
• 2020

The purpose of this study is to evaluate the shrinkage characteristics of the cement-based composite for 3D printing construction, and to evaluate the shrinkage before/after extrusion and after printing during the printing process. As a result of evaluating the compressive strength by curing age of OPC-mix and printing-mix, similar trends were shown until 7 days of age, but the maximum shrinkage of 252 ㎛/m was larger in the case of OPC-mix compared to printing-mix. During the printing process, the compressive strength of the cementitious composite material after extrusion was about 6.5 MPa lower than the material before extrusion until the 7th day of age, but the level of strength on the 28th day of age was similar. As for the shrinkage characteristics, the result of shrinkage after printing showed greater shrinkage in the range of 220-260 ㎛/m compared to the result of shrinkage before extrusion.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.25-28
• /
• 2005

This study shows the early quality improvement of concrete with calcium sulfa aluminate(CSA). For the properties of slump, plain concrete incorporating BS $35\%$ and UP $15\%$ resulted in high fluidity compared with OPC without any admixture. As displacement ratio of CSA increased. the fluidity decreased. The fluidity also declined with setting time. Increase of incorporation ratio of CSA declined bleeding and accelerated setting time. Importantly, using more CSA helped to improve early compressive strength and decrease drying shrinkage. In term of water curing, drying shrinkage hardly ever occurred.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05a
• /
• pp.494-497
• /
• 2006

The objectives of this study are to develop and evaluate the Neural Network algorithm which can predict the inelastic shortening such as the creep strain and the drying shrinkage strain of reinforced concrete members using the previous test data. New learning algorithms for the prediction of creep strain and the drying shrinkage strain are proposed focusing on input layer components and a normalization method for input data and their validity is examined through several test data. In Neural Network algorithm, the main input data to be trained are the compressive strength of the concrete, volume to surface ratio, curing condition, relative humidity, and the applied load. The results show that the new algorithms proposed herein successfully predict creep strain and the drying shrinkage strain.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10b
• /
• pp.674-679
• /
• 1998

In designing the prestressed concrete box-bridge, the dead load, prestressing force, creep and shrinkage of concrete are the main factors which influence the camber and deflection of segmental concrete structure under construction. Among these factors the creep and shrinkage are the functions of the time-dependent property which, therefore, must be considered with time. The prediction model for estimating creep and shrinkage of concrete has been suggested by ACI, CEB/FIP, JSCE and KSCE design code and EMM, AEMM, RCM, IDM and SSM has been suggested for analytical method in consideration of the time-dependent characteristics. In this study, the creep test was carried out for four curing ages of concrete which were applied to the prestressed concrete structure at a construction site, and the results of test were compared to the values of creep prediction by the design code. Also the creep test of step-wise incremental stresses were performed and were compared to analytical methods.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.175-176
• /
• 2010

• Computers and Concrete
• /
• v.33 no.3
• /
• pp.309-324
• /
• 2024

Internal curing, a widely used method for mitigating early-age shrinkage in concrete, also offers notable advantages for concrete durability. This paper explores the potential of internal curing by partial replacement of sand with fine lightweight aggregate for enhancing the behavior of high-performance concrete at elevated temperatures. Such a technique may prove economical and safe for the construction of skyscrapers, where explosive spalling of high-performance concrete in fire is a potential hazard. To reach this aim, the physico-mechanical features of internally cured high-strength concrete specimens, including mass loss, compressive strength, strain at peak stress, modulus of elasticity, stress-strain curve, toughness, and flexural strength, were investigated under different temperature exposures; and to predict some of these mechanical properties, a number of equations were proposed. Based on the experimental results, an advanced stress-strain model was proposed for internally cured high-performance concrete at different temperature levels, the results of which agreed well with the test data. It was observed that the replacement of 10% of sand with pre-wetted fine lightweight expanded clay aggregate (LECA) not only did not reduce the compressive strength at ambient temperature, but also prevented explosive spalling and could retain 20% of its ambient compressive strength after heating up to 800℃. It was then concluded that internal curing is an excellent method to enhance the performance of high-strength concrete at elevated temperatures.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.13 no.3 s.55
• /
• pp.93-100
• /
• 2009

This study forms part of a research project that was carried out on the development and application of high-strength concrete for large underground spaces. In order to develop 50MPa high-strength concrete, eight optimal mixtures with different portions of fly ash and ground granulated blast furnace slag were selected. For assessments of shrinkage characteristics, free shrinkage tests with prismatic specimens and shrinkage crack tests were performed. The compressive strength was more than 30MPa at 7days, and stable design strength was acquired at 28days. High-strength concrete containing blast furnace slag shows large autogenous shrinkage, while large shrinkage deformations and cracks will occur when mixtures are replaced with large volumes of cementitious materials. Hence, for these high-strength concrete mixtures, the curing conditions of initial ages that affect the reaction of hydration and drying effects need to be checked.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.651-654
• /
• 2005

Fast-setting cement is usually used for emergency repair construction of roads, bridges, buildings and so on. In this study, we tried to develop fast-setting ultra early strength mortar for prepacked concrete and evaluated the properties of fresh and hardened concrete with it. The flowability of the mortar was high enough to be easily poured into coarse aggregates. It showed high early strength development which can make it possible to use newly constructed structures within $3\~4$ hours regardless of curing conditions such as curing temperature and curing environment. And it also showed good resistance to drying shrinkage and chemical attack.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2006.11a
• /
• pp.29-32
• /
• 2006

Experimental test results of field construction, Cheongju University Educational Liberal Art Building, applying the insulating curing method on slab concrete showed that the quality of concrete in fresh and hardened state satisfied all target values. Temperature history of slab concrete in A and B area secured more than $7.8{\sim}9.2^{\circ}C$ higher than outside atmosphere. After completing certain curing period of time on the surface of the structure, crack occurrence was not found. It is concluded that the preventing vaporization of moisture by the insulating curing method reduces plastic and drying shrinkage as welt as improves durability.

• Textile Coloration and Finishing
• /
• v.24 no.3
• /
• pp.221-231
• /
• 2012

Rayon fabrics were treated with some commercial non-formaldehyde and low-formaldehyde resins, and then their effect on the physicochemical properties of fabrics, including formaldehyde release, tear strength, shrinkage, and wrinkle recovery, were investigated respectively. Rayons treated with non-formaldehyde resin, little formaldehyde release was observed. Considering other factors, the optimal concentration of non-formaldehyde resin was shown to be 11-13%, and curing temperature was $170{\sim}175^{\circ}C$. In case of low-formaldehyde type, 9-11% resin concentration and curing temperature of $170{\sim}180^{\circ}C$ were recommended for optimal finishing condition. The choice and combination of resins and catalysts were also important factors, and preliminary considerations before resin-finishing of rayon are also important to get much better results.