• Structural Engineering and Mechanics
• /
• v.63 no.1
• /
• pp.125-136
• /
• 2017

This study investigated the performance of a steel column standing on a reinforced concrete footing when it was subjected to collision of an eight-ton single unit truck. Finite element analyses of the structure with different connection schemes were performed using the finite element model of the truck, and the results showed that the behavior of the column subjected to the automobile impact depended largely on the column-footing connection detail. Various reinforcement schemes were investigated to mitigate the damage caused by the car impact. The probability of the model reinforced with a certain scheme to reach a given limit state was obtained by fragility analysis, and the effects of the combined reinforcement methods were investigated based on the equivalent fragility scheme. The analysis results showed that the reinforcement schemes such as increase of the pedestal area, decrease of the pedestal height, and the steel plate jacketing of the pedestal were effective in reducing the damage. As the speed of the automobile increased the contribution of the increase in the number of the anchor bolts and the dowel bars became more important to prevent crushing of the pedestal.

• Steel and Composite Structures
• /
• v.26 no.3
• /
• pp.347-360
• /
• 2018

The aim of this paper is to evaluate the accuracy and reliability of the available bond-slip laws which are being used for the numerical modeling of Fiber Reinforced Polymer (FRP)/concrete interfaces. For this purpose, a set of Reinforced Concrete (RC) beams retrofitted with external FRP were modeled using the 3D nonlinear Finite Element (FE) approach. All considered RC beams have been previously tested and the corresponding experimental data are available in the literature. The failure modes of these beams are concrete crushing, steel yielding and FRP debonding. Through comparison of the numerical and experimental results, the effectiveness of each FRP/concrete bond-slip model for the prediction of the structural behavior of externally retrofitted RC beams is assessed. The sensitivity of the numerical results against different modeling considerations of the concrete constitutive behavior and bond-slip laws has also been evaluated. The results show that the maximum allowable stress of FRP/concrete interface has an important role in the accurate prediction of the FRP debonding failure.

• Structural Engineering and Mechanics
• /
• v.60 no.2
• /
• pp.337-350
• /
• 2016

Even though extensive researches have been performed for steam explosion due to their complex mechanisms and inherent uncertainties, establishment of severe accident management guidelines and strategies is one of state-of-the arts in nuclear industry. The goal of this research is primarily to examine effects of vessel failure modes and locations on nuclear facilities under typical steam explosion conditions. Both discrete and integrated models were employed from the viewpoint of structural integrity assessment of steel components and evaluation of the cracking and crushing in reinforced concrete structures. Thereafter, comparison of systematic analysis results was performed; despite the vessel failure modes were dominant, resulting maximum stresses at the all steel components were sufficiently lower than the corresponding yield strengths. Two failure criteria for the reinforced concrete structures such as the limiting failure ratio of concrete and the limiting strains for rebar and liner plate were satisfied under steam explosion conditions. Moreover, stresses of steel components and reinforced concrete structures were reduced with maximum difference of 12% when the integrated model was adopted comparing to those of discrete models.

• Journal of the Korean Ceramic Society
• /
• v.55 no.1
• /
• pp.36-43
• /
• 2018

The physical and chemical analyses of mineral waste such as moisture content, water absorption, freezing-thawing resisting sexual, chemical composition and crystal structure were investigated. In the technological process of crushing, screening, molding, drying, preheating, sintering and cooling, many parameters were changed to eliminate the influence of freeze thaw stability and the ball billets were processed into slate ceramsites eventually. Adopting orthogonal experiment and range analysis, the optimal technology parameters were confirmed as preheating temperature of $300^{\circ}C$ for 25 minutes and sintering temperature of $1230^{\circ}C$ for 20 minutes. Slate wastes in Shangri-la could foam and expand without any additive. The ultra-light ceramsite could be directly used as building aggregate, since the analysis results of its leaching toxicity were eligible. Besides, effects of sintering temperature on physical property and crystal phase were also explored in this study.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.4 no.1
• /
• pp.111-120
• /
• 2000

This study discusses the issues related to the accuracy of deflection measurement in the testing of FRC. Some deflection methods may include large extraneous deformations. such as local crushing at the loading points, elastic and inelastic deformations of the loading fixture, etc. A faulty load-deflection curve will be obtained if an unstable deflection measuring system is used, and incorrect toughness evaluation can be reached on the basis of this faulty curve. In this paper, the discussion will focus on the effects of the deflection measuring system on both the measurement of the load-deflection response of FRC and the evaluation of FRC toughness. It is observed that ASTM toughness indices which is based on measuring deflection at first cracking is influenced significantly by extraneous deformation in deflection measurement. But extraneous deformation in deflection measurement result in negligible errors in toughness evaluation using JSCE and JCI definition. However, in order to evaluate toughness accuracy, it is desirable to use net load-deflection curve eliminated extraneous deformation.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.1
• /
• pp.19-25
• /
• 2000

In Condebelt press drying system, the temperature difference between top and bottom plate of Condebelt transfers water to bottom side, Fine fibers, stickies , ink , and various inorganic materials are also migrated to the fine wire located at the bottom plate by highly pressurized moisture flow. As a result, the fine wire contaminated by plugging of these fine and sticky materials can cause many problems such as blistering or partial crushing of paper. The contaimination of fine wire leads to a deterioroated strength together with uneven physical properties of paper. In this paper, froth-flotatiion method, which is commonly used in the field of ONP recycling process, were adopted to separate the contaminants in KOCC as a new fiber fractionation method. Standard deviation of paper strength and brighteness decreased of Condebelt fine wire were measured to investigate the effect of contaminants removal . The standard deviations of paper strength obtained from the flotated accept were not dependent on the number of condebelt press drying . However, in the case of untreated KOCC, the standard deviations were increased as press drying repeated. This indicates that the contaminant gives uneven physical properties to the paper by wire plugging . Optical and SEM images clearly illustrate the effect of contaminants on the wire condition.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.26 no.1
• /
• pp.1-11
• /
• 2022

In this study, the seismic performance of a two-story unreinforced masonry (URM) building was assessed following the linear and nonlinear static procedures specified in the seismic evaluation guideline of existing buildings. First, the provisions to assess failure modes and shear strengths of URM walls and wall piers were reviewed. Then, a two-story URM building was assessed by the linear static procedure using m-factors. The results showed that the walls and wall piers with aspect ratios h_e // (i.e., effective height-to-length ratio) > 1.5 were unsafe due to rocking or toe crushing, whereas the walls with h_e // ≤ 1.5 and governed by bed-joint sliding mainly were safe. Axial stresses and shear forces acted upon individual masonry walls, and wall piers differed depending on whether the openings were modeled. The masonry building was reevaluated according to the nonlinear static procedure for a more refined assessment. Based on the linear and nonlinear assessment results, considerations of seismic evaluation for low-rise masonry buildings were given with a focus on the effects of openings.

• Korean Journal of Materials Research
• /
• v.22 no.9
• /
• pp.445-449
• /
• 2012

We investigate the effects of redox reaction on preparation of high purity ${\alpha}$-alumina from selectively ground aluminum dross. Preparation procedure of the ${\alpha}$-alumina from the aluminum dross has four steps: i) selective crushing and grinding, ii) leaching process, iii) redox reaction, and iv) precipitation reaction under controlled pH. Aluminum dross supplied from a smelter was ground to separate metallic aluminum. After the separation, the recovered particles were treated with hydrochloric acid(HCl) to leach aluminum as aluminum chloride solution. Then, the aluminum chloride solution was applied to a redox reaction with hydrogen peroxide($H_2O_2$). The pH value of the solution was controlled by addition of ammonia to obtain aluminum hydroxide and to remove other impurities. Then, the obtained aluminum hydroxide was dried at $60^{\circ}C$ and heat-treated at $1300^{\circ}C$ to form ${\alpha}$-alumina. Aluminum dross was found to contain a complex mixture of aluminum metal, aluminum oxide, aluminum nitride, and spinel compounds. Regardless of introduction of the redox reaction, both of the sintered products are composed mainly of ${\alpha}$-alumina. There were fewer impurities in the solution subject to the redox reaction than there were in the solution that was not subject to the redox reaction. The impurities were precipitated by pH control with ammonia solution, and then removed. We can obtain aluminum hydroxide with high purity through control of pH after the redox reaction. Thus, pH control brings a synthesis of ${\alpha}$-alumina with fewer impurities after the redox reaction. Consequently, high purity ${\alpha}$-alumina from aluminum dross can be fabricated through the process by redox reaction.

• Resources Recycling
• /
• v.25 no.2
• /
• pp.17-24
• /
• 2016

This study aims at evaluating environmental impacts on recycling process of used small household appliances. The recycling process mainly consists of manual dismantling, crushing and various sorting processes to effectively recover valuable resources and to minimize environmental impact. In this study, life-cycle assessment (LCA) methodology is applied to analyze major environmental parameters such as GWP, ADP, POCP, EP, etc. One of the major impact categories on the weight basis in the recycling process is global warming (GWP) 57.1%, next to ADP 35.4% and POCP 4.8%, respectively. As a result of environmental impact on recovery of valuable resources/ton, the GWP of plastics for ABS is highest (33.7%) compared to ferrous metals (9.4%). The effects of environmental and economical benefit are also analyzed to compare with the amount of virgin materials to be recycled by recycled materials. In addition, recycled materials are also more economical in comparison to virgin materials due to the environmental avoiding effect by recycling. In conclusion, the key environmental issues related to the recycling of e-wastes are analyzed and therefore, the effective recycling process will contribute to mitigate global warming potential in the near future.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.25 no.4
• /
• pp.589-595
• /
• 2011

In order to analyze principles of taking concoction and make clear the origin of contraindication against five pungent vegetables, the regulations of Guizhitang prescription in "Shanghanlun" the twelfth article and "Wushierbingfang", "Wuweihandaiyijian", "Jinguiyaolue" were researched. Four principles of taking concoction were put in order; strengthening the effect of concoction by eating hot rice gruel and wearing bedclothes, preventing decline of drug effect by food regulations, optimization of elution and effect of material herbs by crushing, low heating, determination of administration time based on manifestations of drug effect by sweating and its aspect. These principles and methods of taking concoctions were developed from boiling to simple processing of material herbs, contraindication in the middle of taking concoction and perspiration by wearing bedclothes and eating hot rice gruel in order from the analysis of medical literatures. The contraindication against pungent vegetables were generalized in early Dong-Han dynasty already, and the five pungent vegetables were inferred as Allium tuberosum, Allium bakeri regel, spring onion, wild rocambole and garlic in medical context to the exclusion of religious idea. The reason of prohibition against five pungent vegetables could be interpreted as optimization of therapeutic effects by pharmacological control of pungent ingredients because the healthy qi damage and evil qi retention were resulted from destroying of harmonious ying and wei by overeating pungent vegetables during disease state. Conclusively the regulations of Guizhitang prescription referred to taking concoction in "Shanghanlun" fulfilled their functions to maximize pharmacological effects through various ways inside and outside and these reasonal principles of taking concoction has been influenced over the traditional medical practice deeply.