• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1425-1427
• /
• 2002

Degree of crosslinking of insulation is very important factor that is determined characteristics of XLPE insulated power cable. Increase of degree of crosslinking is closely related to increase of mechanical characteristics of XLPE insulated power cable. In this study, mechanical characteristics of XLPE insulation for degree of crosslinking was analyzed tensile strength and elongation of insulation. As the result, mechanical characteristics of insulation for degree of crosslinking was divided three cases.

• Polymer(Korea)
• /
• v.25 no.5
• /
• pp.657-664
• /
• 2001

In this study. the effects of ${\gamma}$-irradiation on the crosslinking of low density poly ethylene (LLDPE) and linear low density polyethylene (LLDPE) containing crosslinking agents were investigated to find the degree of crosslinking in the polymer. The LDPE and LLDPE specimens were prepared by blending crosslinking agents with each polymers, and by hot-press-molding into a sheet at 13$0^{\circ}C$. The ${\gamma}$-irradiation was conducted at 50 to 150 kGy in nitrogen. The crosslinking percentage in these specimens was measured in relation to the irradiation dose and the type of crosslinking agents. The mechanical properties, thermal properties and crystallinity of specimens were examined as a function of irradiation dose as well. It was found that the degree of crosslinking of the irradiated specimens was increased with increasing irradiation dose and by the addition of crosslinking agents. The mechanical properties and thermal properties of specimens were improved in proportion to an increase in the degree of crosslinking. The crystallinity of original resin was decreased with increasing crosslinking density.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.130-134
• /
• 1997

The structural defects, impurities, degree of crosslinking and shrinkage of 38 field-aged distribution cables have been analyzed. For the comparison of data, 9 new cables were also subjected to an analysis. It is observed that the structural defects and degree of crosslinking show a radial profile. The structural defects are different depending on the manufacturer. A large amount of impurities is present in the insulation shield, which hold true for the new cables manufactured recently. The degree of crosslinking near both shields is lower than that at the central region of the insulation layer. It was also found that, in some cal)toes, the ins난lation was not fully crosslinked. The shrinkage of field-aged cables is higher than that of new cables.

• Journal of the Korean Applied Science and Technology
• /
• v.38 no.1
• /
• pp.300-308
• /
• 2021

In this study, 3D networked poly(sodium acrylate) gel was polymerized and controlled with the crosslinking environment to evaluate the mechanical properties and swelling behavior. In general, as the degree of crosslinking in a pre-gelled solution increases, the swelling ratio of the 3D networked gel decrease while the mechanical strength of the gel increases. Interestingly, this study demonstrates that the polymerization and crosslinking efficiency in gelling process could be depended on the crosslinking environment by evaluating the number of elastically cross-links in 3D networked gel. As a result, the number of elastically corss-links would be changed with 3.6 times as varying of the crosslinking environment while keeping the degree of crosslinking. It is expected that the 3D networked gel would be optimized as an effective absorbing agent for VOCs by using the gel evaluation method based on the number of elastically cross-links.

• Journal of Radiation Industry
• /
• v.5 no.2
• /
• pp.107-112
• /
• 2011

Electron beam-induced crosslinking of polycaprolactone (PCL) films containing various crosslinking agents (CAs) was investigated in this study. PCL films containing various CAs prepared by a solution casting method were irradiated by electron beams at various absorption doses and the irradiated PCL films were investigated in terms of their crosslinking degree, thermal and mechanical properties, and biodegradability. Based on the results of the crosslinking degree measurement, triallyl isocyanurate was found to be most effective for the electron-beam induced crosslinking of PCL films. The results of the UTM, DMA, and TMA revealed that the thermal and mechanical properties of the crosslinked PCL films were greatly improved in comparison to those of the pure PCL. The results of the enzymatic degradation test revealed that the biodegradability of the crosslinked PCL films was reduced in comparison to that of the pure PCL.

• Journal of Radiation Industry
• /
• v.6 no.2
• /
• pp.171-176
• /
• 2012

In this study, a crosslinked poly(styrene-butadiene-styrene) [SBS] block copolymers were prepared by using gamma ray irradiation method. The effects of various radiation doses on the degree of crosslinking, thermo property, and morphology of crosslinked SBS block copolymer were investigated. The degree of crosslinking of crosslinked SBS block copolymers were measured by gel-fraction and FT-IR. It was found that the degree of crosslinking of crosslinked SBS block copolymers increases with increase of the irradiation dose while the TGA result shows that the initial degradation temperature of irradiated SBS block copolymer was shifted to lower temperature with increasing irradiation dose. These results indicate that degradation reaction also occurs when SBS block copolymer is exposed to gamma ray irradiation for crosslinking reaction. The SAXS and FE-SEM results indicate that the phase separation of the styrene block and butadiene block was reduced with increasing irradiation dose.

• Membrane Journal
• /
• v.30 no.1
• /
• pp.21-29
• /
• 2020

In this study, we have established the optimum design condition of pore-filled anion-exchange membrane for all-vanadium redox flow battery (VRFB). From the experimental results, it was proven that the membrane design factors that have the greatest influence on the charge-discharge performance of VRFB are the ion exchange capacity, the porosity of substrate film, and the crosslinking degree. That is, the ohmic loss and the crossover of active materials in VRFB were shown to be determined by the above factors. In addition, two methods, i.e. reducing the ion exchange capacity at low crosslinking degree and increasing the crosslinking degree at high ion exchange capacity, were investigated in the preparation of pore-filled anion-exchange membranes. As a result, it was found that optimizing the crosslinking degree at sufficiently high ion exchange capacity is more desirable to achieving high VRFB charge-discharge performances.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.424.1-424.1
• /
• 2016

태양전지 모듈의 봉지재로 사용되는 EVA(Ethylene-Vinyl acetate)는 외부의 환경으로부터 태양전지를 보호해주는 역할을 한다. 하지만 frame의 실링재나 glass edge 부분의 결함으로 인해 수분이 침투되어 모듈의 내부자재에 영향을 미치게 되며, 모듈의 효율 감소나 수명 단축의 원인이 된다. 이러한 결함을 줄이기 위해서는 EVA의 crosslinking degree, 절연 저항 특성을 향상시키는 것이 중요하다. 이에 본 연구에서는 EVA의 crosslinking degree를 보기 위해 soxhlet extraction method를 이용하여 gel content를 측정하였으며, 라미네이션 과정 중 curing time에 따른 gel content 변화를 확인하였다. 또한 이 실험을 바탕으로 gel content에 따른 절연 저항을 측정하여 EVA의 crosslinking degree에 의한 절연 저항 특성을 확인하였다.

• Korean Journal of Food Science and Technology
• /
• v.28 no.3
• /
• pp.580-586
• /
• 1996

Gelatinization behavior and morphology of epichlorohydrin-crosslinked potato starches (XPs) were investigated. Native potato starch showed a very steep single stage swlling pattern, but crosslinked starches showed various patterns with the degree of crosslinking. Swelling power, solubility and light transmittance were reduced drastically as the degree of crosslinking increased. Brabender initial pasting temperature and peak temperature of crosslinked starches increased because the crosslinking reinforces the intermolecular net work of the starches. Although the swelling of the potato starch granule was inhibited by crosslinking as compared to that of the native one, Brabender peak viscosities (6.5% w/v, db) were on the order of 2,500 units for the native potato starch, 3,700 for the XP with 2.300 anhydroglucose units per crosslinking (AGU/CL) and 3,400 for the XP with 2,100 AGU/CL, due to the decreased breakdown of the swollen granule resulting from the resistance to heat and shear. The XP with 1,900 AGU/CL, however, did not show the peak viscosity and the viscosity was on the order of 500 units because of the excessive unhibition of the swelling. Unlike the native potato starch, 6.5%(m/v, db) pastes of the crosslinked potato starches could form gels, which could be predicted from the Brabender setback and consistency index. When the degree of crosslinking is low, random contraction and radial swelling of the granule was possible. As the degree of crosslinking increased, morphological change became similar to the single dimensional tangential swelling observed from the lenticular wheat starch. These morphological change during heating in excess water explained the gelatinization behaviors of crosslinked starches tested.

• Polymer(Korea)
• /
• v.29 no.6
• /
• pp.599-604
• /
• 2005

The hyaluronic acid (HA) with excellent biocompatibility has been combined with lactide, the ester dimer of polylactide, with good biodegradability to produce biocompatible materials which can control the period of degradation in a human body. By freeze frying method, HA and lactide were crosslinked with crosslinking agent, 1-ethyl-3-(3-dimethyl aminopropyl) carbodiimide (EDC). Degree of lactide and EDC reaction was determined by the analysis of nuclear magnetic resonance spectroscopy. Both lactyl group and EDC conversion increased as the mole ratio of lactide to HA increased from 5 to 13. The membrane swelled less and became more brittle with the more addition of lactyl group resulting from the higher mole ratio of lactide to HA. Swelling ratio decreased and tensile modulus increased due to the more addition of lactyl group as the EDC concentration increased or reaction temperature decreased. Drug release experiment from various membranes with different degree of crosslinking showed that permeability decreased with increasing degree of crosslinking. The degradation became slower with the more addition of lactyl group. Mechanical property and degradation rate of the synthesized membrane were shown to be controlled through adjusting operation parameters such as mole ratio, temperature, and crosslinking agent concentration.