• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.75-78
• /
• 2004

Various jet engines (Turbine engine family and RAM Jet engine) have been developed for high speed aircrafts. but their application to hypersonic flight is restricted by principle problems such as increase of total pressure loss and thermal stress. Therefore, the development of next generation propulsion system for hypersonic aircraft is a very important subject in the aerospace engineering field, SCRAM Jet engine based on a key technology, Supersonic Combustion. is supposed as the best choice for the hypersonic flight. Since Supersonic Combustion requires both rapid ignition and stable flame holding within supersonic air stream, much attention have to be given on the mixing state between air stream and fuel flow. However. the wider diffusion of fuel is expected with less total pressure loss in the supersonic air stream. So. in this study the direction of fuel injection is inclined 30 degree to downstream and the total pressure of jet is controlled for lower penetration height than thickness of boundary layer. Under these flow configuration both streams, fuel and supersonic air stream, would not mix enough. To spread fuel wider into supersonic air an aerodynamic force, baroclinic torque, is adopted. Baroclinic torque is generated by a spatial misalignment between pressure gradient (shock wave plane) and density gradient (mixing layer). A wedge is installed in downstream of injector orifice to induce an oblique shock. The schlieren optical visualization from side transparent wall and the total pressure measurement at exit cross section of combustor estimate how mixing is enhanced by the incidence of shock wave into supersonic boundary layer composed by fuel and air. In this study non-combustionable helium gas is injected with total pressure 0.66㎫ instead of flammable fuel to clarify mixing process. Mach number 1.8. total pressure O.5㎫, total temperature 288K are set up for supersonic air stream.

• Physical Therapy Rehabilitation Science
• /
• v.6 no.1
• /
• pp.33-38
• /
• 2017

Objective: This study tried to examine the muscle activity of the neck and trunk according to head posture changes during use of laptops. Design: Cross-sectional study. Methods: This study included nineteen young men and women. All subjects maintained each posture while practice typing on laptops for ten minutes with a 5-minute break between each posture. For the neutral head posture, the subjects practiced typing while pulling their chins down towards the Adam's apple and were able to look at their knees while having their external auditory meatus, acromion, and greater trochanter vertical to the ground. For the natural head posture, they practiced typing while balancing their posture between extension and flexion of the cervical vertebrae by themselves without any guidelines. While a forward head posture was created by having their heads face the front horizontal to the rope hanging from the ceiling, they practiced typing with their external auditory meatus located in the place which was 5 cm in front of the vertical plane. The subjects used general word process but practiced typing with accuracy and high speed. Muscle activities were randomly measured using surface electromyography according to each postures. Results: The research result had found that muscle activity with the natural head posture was more significantly reduced than that of the forward head posture in the sternocleidomastoid muscle, upper trapezius, cervical vertebral spinae, and thoracic vertebrae spinae muscles (p<0.05) and that the neutral head posture was more significantly reduced than that of forward head posture in the upper trapezius, cervical vertebral spinae, and thoracic vertebrae spinae muscle activity (p<0.05) with significant increases in lumbar spinae muscle activity (p<0.05). Also, muscle activity with the neutral head posture significantly increased more in the sternocleidomastoid muscle and lumbar spinae than that of the natural posture (p<0.05). Conclusions: Our study results suggest that in order to prevent musculoskeletal pain, the neutral head posture with use of laptops is effective in reducing load to the shoulders and vitalizing the postural muscles.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.4 s.95
• /
• pp.397-401
• /
• 2005

In this paper, a slot-coupled microstrip antenna with switchable polarization is proposed for the polarization diversity applications in the complicated communication environment. The proposed antenna is fed by a microstrip line through one of two slots located with the interval of $\lambda{g}/4$ in the ground plane. By switching the PIN diode between opened and shorted termination which is located at the tip of the microstrip line, the switching function between horizontal and vertical polarization was confirmed experimentally. The measured resonant frequencies of the fabricated antenna are $2.41\;\cal{GHz}\;2.40\;\cal{GHz}$ and the cross polarization levels are $19\;\cal{dB},\;23\;\cal{dB},\;the\;-10\;\cal{dB}$ return loss bandwidths are $95\;\cal{MHz}\;100\;\cal{MHz}$ in horizontal and vertical polarization, respectively, and the antenna gain is almost $6\;\cal{dBi}$.

• Journal of electromagnetic engineering and science
• /
• v.18 no.2
• /
• pp.117-128
• /
• 2018

In this paper, compact linear dual polarized series-fed $1{\times}2$ linear and $2{\times}2$ planar arrays antennas for airborne SAR applications are proposed. The proposed antenna design consists of a square radiating patch that is placed on top of the substrate, a quarter wave transformer and $50-{\Omega}$ matched transformer. Matching between a radiating patch and the $50-{\Omega}$ microstrip line is accomplished through a direct coupled-feed technique with the help of an impedance inverter (${\lambda}/4$ impedance transformer) placed at both horizontal and vertical planes, in the case of the $2{\times}2$ planar array. The overall size for the prototype-1 and prototype-2 fabricated antennas are $1.9305{\times}0.9652{\times}0.05106{{\lambda}_0}^3$ and $1.9305{\times}1.9305{\times}0.05106{{\lambda}_0}^3$, respectively. The fabricated structure has been tested, and the experimental results are similar to the simulated ones. The CST MWS simulated and vector network analyzer measured reflection coefficient ($S_{11}$) results were compared, and they indicate that the proposed antenna prototype-1 yields the impedance bandwidth >140 MHz (9.56-9.72 GHz) defined by $S_{11}$<-10 dB with 1.43%, and $S_{21}$<-25 dB in the case of prototype-2 (9.58-9.74 GHz, $S_{11}$< -10 dB) >140 MHz for all the individual ports. The surface currents and the E- and H-field distributions were studied for a better understanding of the polarization mechanism. The measured results of the proposed dual polarized antenna were in accordance with the simulated analysis and showed good performance of the S-parameters and radiation patterns (co-pol and cross-pol), gain, efficiency, front-to-back ratio, half-power beam width) at the resonant frequency. With these features and its compact size, the proposed antenna will be suitable for X-band airborne synthetic aperture radar applications.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.10a
• /
• pp.335-340
• /
• 2002

In recent years, the study of metal matrix composite has increased specially, aluminum alloy, research and development are briskly progress to find new metal matrix composite. this study is following the this purpose; This study is used metal matrix composite that was produced by matrix, AC4CH. and reinforcement $A_{18}B_4O_{33}$ metal matrix composite to add $Al_2O_3,\;TiO_2$ for strengthen of binding together among the Whisker. Each Metal matrix composite is produced using the squeeze casting method. Fracture tounghness test was in accordance with the provisions of ASTM E399; Specimen was produced half-size CT specimen W=25mm, B=12.5mm, Cross head speed 0.05mm/min in room temperature. The plane strain fracture toughness $K_{IC}$ is $8.7MPa-m^{0.5}$ for $Al_{18}B_4O_{33}$/AC4CH., $9.28MPa-m^{0.5}$ for $Al_{18}B_4O_{33}$/AC4CH added $TiO_2$. and $Al_2O_3$ but AC4CH alloy was violated the critical stipulated by ASTM standard for a valid measurement of $K_{IC}$. In case of, it was performed $I_{IC}$ test instead of $K_{IC}$ based on ASTM E 1820

• Journal of Energy Engineering
• /
• v.23 no.2
• /
• pp.35-41
• /
• 2014

The present study has been carried out to reduce the heat loss from a refrigerator by numerical heat transfer analysis and temperature measurement experiment for the verification of heat transfer analysis result. To perform this purpose, two dimensional heat transfer analysis and measurement of temperature on the surface of freezer for the horizontal cross sectional plane of a refrigerator has been accomplished. From the present study, it could be seen that the steel support in the mullion near gasket region has a heat transfer characteristics which transfer outside heat well from the high temperature hotline and outside air to the inner refrigerator. The effect of removing steel support on the reducing heat loss of a refrigerator was 24.8% and removing steel support might introduce significant improvement of refrigerator heat loss.

• 한국방재학회:학술대회논문집
• /
• 2008.02a
• /
• pp.739-742
• /
• 2008

Surface Image Velocity (SIV) is a technique which measures the surface velocity of river by using the principle of Paticle Image Velocimetry (PIV). The technique is economical and efficient way to measure velocity in rivers. The present paper aims to apply the technique to three rivers in Korea. It uses pairs of river surface images taken with two digital-cameras and reference points and cross section data which were acquired through plane survey. The performance of SIV was verified with automatic cart on an experimental flume. The test revealed that average error was less than 10 %, which assures that SIV can be used to measure velocity accurately. When it was applied to rivers with low water levels or rough weather condition, however, it showed the error about 20 %. If the problems of SIV technique are settled down, it can be one of the most convenient and economical ways to measure water discharge anytime and anywhere. And then it would be helpful to river management as developing a real-time river information system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.12
• /
• pp.2763-2768
• /
• 2013

In this paper, a design method for a compact slot antenna for 5.8 GHz RFID band (5.725-5.875 GHz) is studied. The proposed slot antenna is size-reduced by bending both ends of the straight slot in "I"-shape, and a rectangular feed patch is located inside the slot. The effects of slot length, location of feed patch, and width and length of feed patch on the antenna performance are examined. A prototype antenna with optimized parameters for 5.8 GHz band is fabricated on an FR4 substrate and tested experimentally to verify the results of this study. The experimental results show that the frequency band for a VSWR < 3 ranges 5.72-6.13 GHz (bandwidth 410 MHz), and it corresponds fairly well with the simulated band 5.64-5.97 GHz (bandwidth 330 MHz). The fabricated antenna shows good radiation performance such as maximum power density in both directions normal to the slot plane, low cross-polarization level of < -20 dB, and realized gain > 0 dBi within the frequency band.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.1
• /
• pp.190-196
• /
• 2013

Curved integral imaging is a simple method to display 3D images in space using lens array and provides wide viewing angle. In this paper, we propose a nonlinear 3D correlator based on the direct pixel-mapping (DPM) method in order to improve the recognition performance of 3D target object in curving-effective integral imaging. With this scheme, the elemental image array (EIA) originally picked up from a partially occluded 3-D target object can be converted into a resolution enhanced new EIA by using DPM method. Then, through nonlinear cross-correlations between the reconstructed reference and the target plane images, the improved pattern recognition can be performed from the correlation outputs. To show the feasibility of the proposed method, some preliminary experiments are carried out and results are presented by comparing the conventional method.

• Parasites, Hosts and Diseases
• /
• v.33 no.3
• /
• pp.231-234
• /
• 1995

Anisakid larvae were found from the liver and stomach of the codfish (Notothenia negzecta) caught from the Antarctic Ocean, South Pole, where the Polar Research Center of The Korea Ocean Research and Development Institute is operating- Through observations by scanning electron (SEM) and light microscopy (LM), they were identified as the third stage larvae of Pseunotewnnovo necipiens, a potential agent of human codworm anisakiasis. They measured 25.0-28.5 mm in length, and 0.6-0.8 mm in width. The SEM revealed a prominent boring tooth, three lips, and excretory pore at the anterior end, and a small but prominent mucron at the posterior end. From whole mounts and cross sections of the larvae the ventriculus, intestinal cecum and a Renette cell were found characteristically at the same plane. Raw eating of the codfish caught from the Antarctic Ocean near the South Pole should be avoided so as to prevent human codworm anisakiasis in this area.