• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.58 no.4
• /
• pp.632-632
• /
• 2009

The purpose of this study is to present the range of defects mentioned in the Product Liability (PL) and to establish an objective basis and grounds for the analysis of accidents expected to happen by analyzing and presenting the external flame pattern and electrical characteristics of an LED streetlight lamp, a new lighting lamp. From the analysis of the cross-section of a cable carbonized by an external flame, it was observed that the wire's strand and insulation material had solidly adhered, and that greater voids were formed at the surface than at the center. Irregular carbide lumps were formed in the globe directly exposed to the flame, and the globe carbonized by the indirect flame showed characteristics that they had melted and flowed downward. It was found that the forward and backward resistances of the normal LED were approximately 1.74 [$M{\Omega}$] and 140 [$M{\Omega}$], respectively. The lamp burnt by the strong flame exhibited infinite forward and backward resistances and the LED did not emit light. The carbonized LED lamp was gray and exhibited fine delaminations. According to the Product Liability, a product defect signifies a simple product defect. Most of the defects were caused by the lack of stability, and the defect of the product itself occurred during the design and manufacture. The defects in warnings and markings include an insufficiency of handling manuals and warnings, expressive warranty violations, defective markings, etc. In order to prevent an accident resulting from a product, it is necessary to prepare safety warnings and documentation, establish clear-cut lines of liabilities, and subscribe insurances. However, it could be seen that important factors against the Product Liability were product improvement, response to compensation requests and law suits, credit restoration, etc.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.98-106
• /
• 1999

In this study cold rolling process for the irregular cross-sectional shape has been investigated. The product analyzed in present study is the steel cutter, which is frequently used to cut the desired shape on leather. Because steel cutter always has a irregular cross-section, after rolling process the workpiece is severely bended to every direction. The bending of the workpiece affects the processed performed after rolling such as heat treatment and grinding, then that of the workpiece becomes more severe. In this study, therefore, to prevent the bending of the workpiece to the left and right sides. rigid-plastic finite element method has been utilized and in order to find optimal roll geometry rapidly, one dimensional equal interval search technique has been also introduced. By using both rigid plastic finite element method and optimum technique, cold rolling process for the irregular cross-sectional shape has been successfully investigated.

• Transactions of Materials Processing
• /
• v.18 no.4
• /
• pp.323-328
• /
• 2009

The prediction of drawing load is very important in the drawing process. However, it is not easy to calculate the drawing load for the shape drawing process through a theoretical model because of a complex arbitrary final cross section shape. The purpose of this study is to predict drawing load in shape drawing process. The cross section of product is divided with small angle as much as similar with fan-shape. The drawing load of each section was calculated by theoretical model of round to round drawing process. And the shape drawing load was determined by summation of drawing load of each section. The effectiveness of the proposed method was verified through the FE analysis and shape drawing experiment. It had a good agreement between proposed method, FE analysis and experiment within about 3% errors.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1769-1774
• /
• 2003

Reverse Engineering has wasted high cost and much of time because there were few softwares for supporting post-process of 3D scanning efficiently. However today Reverse Engineering is attracted by various researchers on a count of its practical use and gradually improved quality. Accordingly, many industries induce the technology of Reverse Engineering. For keeping with this general trend, the algorithms of generating meshes from 3D scanning data and visualizing their cross section are suggested in this research. It is expected that output data from the algorithms can be used in inspecting errors between product designs and their final products, and in finding a way to improve quality by considering ideal model data.

• Transactions of Materials Processing
• /
• v.5 no.2
• /
• pp.138-144
• /
• 1996

The differences of formability with maximum cup depth of drawn product and thickness strain distribution are compared for two kinds of blank shapes which are suggested optimum shape and conventional square shape. The suggested blank is determined by backward tracing technique of rigid-plastic FEM. The deeper cup without wrinkle and flange part could be obtained from the suggested blank shape however the cross sevtion sup from the square blank could not be kept smooth thickness strain distribution and defended those phenomena..

• Journal of the Semiconductor & Display Technology
• /
• v.22 no.2
• /
• pp.40-44
• /
• 2023

The defect detection based on deep learning requires minimal loss and high accuracy to pinpoint product defects. In this paper, we confirm the loss rate of deep learning training based on disc-shaped artificial scaffold images. It is intended to compare the performance of Cross-Entropy functions used in object detection algorithms. The model was constructed using normal, defective artificial scaffold images and category cross entropy and sparse category cross entropy. The data was repeatedly learned five times using each loss function. The average loss rate, average accuracy, final loss rate, and final accuracy according to the loss function were confirmed.

• Proceedings of the Korean Reliability Society Conference
• /
• 2001.06a
• /
• pp.215-218
• /
• 2001

We consider Part 2 of IEC300(IEC300-2), which describes the elements of a dependability programme and gives guidance on the selection of tasks necessary to achieve specified dependability of products. This standard cross-references and complements ISO 9004-1. It is applicable to hardware and systems containing software product.

• Proceedings of the Korea Society of Design Studies Conference
• /
• 2005.10a
• /
• pp.46-47
• /
• 2005

• Honam Mathematical Journal
• /
• v.43 no.3
• /
• pp.385-402
• /
• 2021

The geometry of Poincaré disk itself is interpreted without any mapping to different spaces. Our approach might be one of the shortest and is intended for educational contribution.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.285-288
• /
• 2003

The bending phenomenon during extruding one product using four billets can be obtain by the difference of hole diameters in the multi-hole container. The difference of hole diameter caused the difference of billet amount inserted in the die cavity. As results, it can bend during extruding products by the different amount of two billets and by the cohesion of billets in the porthole dies cavity. And the bending curvature can be controlled by the size of holes and billets. The experiments using aluminium material had been done for the rectangular and square curved tube product. The results of the experiment show that the curved aluminum tube product can be bended by the extru-bending process without the defects such as the distortion of section and the thickness change of the wall of tube and the folding and wrinkling. The curvature of product is affected by shape of cross section and the difference of billet diameters. It is known that the welding and extruding and bending can be done simultaneously in the die cavity when a rectangular hollow curved tube would be extruded by porthole dies using four different size billets made of aluminum material.