• 한국구조물진단유지관리공학회 논문집
• /
• 제16권2호
• /
• pp.75-86
• /
• 2012

본 논문에서는 FR-ECC의 수축특성과 균열도입 전후의 내동해성을 평가하였으며, FR-ECC를 활용한 다층복공구조의 지수성능과 박리박락저항성, 또한 FR-ECC로 단면복구 된 보부재의 휨성능을 평가하였다. 그 결과, FR-ECC는 소성수축에 의한 균열 및 건조수축에 의한 길이변화율이 기존의 보수모르터에 비해 크게 저감되었으며, 구속상태에서의 건조수축에 대한 균열저항성이 개선됨을 알 수 있었다. 또한, FR-ECC는 내동해성이 매우 우수하였으며, 균열도입 후에도 동결융해작용에 의한 인장성능의 저하는 확인되지 않았다. 한편, FR-ECC로 보수된 휨부재는 초기균열모멘트, 항복모멘트 및 극한모멘트 등의 휨성능이 증대되었으며, 멀티플크랙 특성에 의해 휨파괴시까지 균열폭을 안정적으로 제어할 수 있었다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2017년도 춘계 학술논문 발표대회
• /
• pp.127-128
• /
• 2017

Tests are conducted according to the ISO TS 16774, Part 3 standard for quality management of leakage repair materials used in cracks in underground concrete structures. These test methods are performed indirectly using a nonwoven fabric on a chalet containing leak repair materials. However, it is considered that it is appropriate to verify the resistance of the repair material, which is required to be applied directly to the cracks in the actual field and to exhibit the resistance of the flow velocity. In this study, mass change was measured by using nonwoven fabric and nonwoven fabric. As a result, both methods showed an increase in mass, which indicated that the maintenance material itself contained a large amount of water, and that the mass change occurred depending on the drying state. Also, depending on the use of nonwoven fabric, the error due to the indirect test could not be ruled out. Therefore, further verification is needed, and it is considered that the test for change of mass reduction measurement is necessary according to the drying time of other types of the same series.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2018년도 춘계 학술논문 발표대회
• /
• pp.105-106
• /
• 2018

Cracks are typical defects that occur in concrete structures. When cracks occur in the structure, durability reduction, concrete neutralization, and steel corrosion cause functional safety problems. In order to prevent such cracks, surface repair method is performed for cracks smaller than 0.3 mm and rechargeable method is performed for cracks larger than 0.3 mm. However, even if it is applied by the surface repair method at less than 0.3 mm, re-leakage cracks continue to occur. Recently, the Supreme Court ruled that the rechargeable method should be applied to cracks less than 0.3mm in order to reduce the occurrence of defects. However, it was considered that the repair fees were too high relative to the observed defect rate, resulting in a necessitation of modifying the existing construction analysis administration standards. This study analyzes the differences in the subjective views on the durability degradation with regards to surface repair methods in concrete structures.

• 대한토목학회논문집
• /
• 제34권4호
• /
• pp.1289-1298
• /
• 2014

도로면 크랙실링 공법은 균열발생 초기에 도로면을 보수하여 균열의 확산을 예방하는 유지보수공법으로써 북미를 중심으로 한 선진 외국에서는 이미 오래전부터 많은 도로 보수 물량에 적용되어 왔다. 그러나 재래식 크랙실링 공법은 작업 특성상 교통량이 많은 일반도로나 고속국도에서 작업이 수행되므로 교통사고가 빈번하게 발생하고, 가열된 실런트를 도로면에 직접 분사하기 때문에 화상의 위험으로부터 노무자의 안전을 확보하기 어려운 문제점이 있다. 이러한 문제점을 해결하기 위하여 선진 외국에서는 1990년대 초부터 ARMM, OCCSM, TTLS 등의 크랙실링 자동화 장비를 지속적으로 연구 개발해 왔으며, 국내에서도 2004년 APCS 장비와 2013년 ACSTM 장비를 개발 완료한 바 있다. 그러나 다수의 연구기관에서 서로 상이한 시기에 개발된 크랙실링 자동화 장비는 각기 다른 테스트베드 조건과 생산성 측정 방법을 사용하여 개발 장비의 작업 생산성을 측정, 표기함으로써 각 크랙실링 자동화 장비의 성능을 객관적으로 비교, 평가할 수 없는 문제점이 있었다. 이 연구에서는 동일한 환경 조건 내에서 크랙실링 자동화 장비의 생산성을 측정하기 위해 완전자동 맵핑 및 반자동 맵핑 방식에 따른 각 크랙실링 자동화 장비의 이미지 프로세싱 소요시간을 추정하고, 작업 프로세스상의 동작요소별 이동시간을 산정하였다. 또한 국내 도로환경이 반영된 생산성 측정 테스트베드를 설계하였으며, 이를 기반으로 국내외에서 개발된 크랙실링 자동화 장비의 생산성을 동일한 조건 내에서 측정하고 상호 비교, 분석하였다.

• Nuclear Engineering and Technology
• /
• 제52권9호
• /
• pp.2092-2099
• /
• 2020

Many damages due to flow-accelerated corrosion and cracking have been observed during recent in-service inspections of nuclear power plants. To determine the operability or repair for damaged pipes, an integrity evaluation related to the damaged piping system should be performed by using already proven code and standards. One of them, the ASME Code Case is most popularly used to integrity assessment in nuclear power plants. However, the recent version of CC N-513 still recommends the simplified method which means a damaged elbow is assumed as an equivalent straight pipe. In addition, to enhance the accuracy integrity assessment in elbow, several previous studies recommend that the SIF and elastic COD values for an elbow with relatively large crack could be predicted by an interpolation technique. However, those estimates for elbow with relatively large crack might be derived to inaccurate results for crack growth analysis, such as for the allowable crack size and life estimation. Therefore, in this paper, the effect of crack length (0.3≤θ₁/π≤0.5) on SIF and elastic COD for elbow is systematically investigated. Then, for large crack in elbow, accurate estimates for SIF and elastic COD, which are widely used to assess the integrity of elbows, are proposed. Those proposed solutions are expected to be the technical basis for revisions of CC N-513-4 through the validation.

• International Journal of Concrete Structures and Materials
• /
• 제2권1호
• /
• pp.3-8
• /
• 2008

Polymer-cement composites are known repair materials. The aim of this work is to investigate the influence of various amount of dispersion of carboxylated styrene-butadience copolymer on the selected mechanical properties of polymer-cement concrete (PCC) and on its adhesion to ordinary concrete. The compressive, flexural and tensile strengths as well as frost resistance and fracture resistance of the composites are tested. Adhesion strength of PCC to ordinary concrete, as one of most important performance of good repair material is evaluated and analyzed using three test methods. The results obtained in standard pull-off test are compared with the two other tests. The first one, which is an adaptation of WST (wedge splitting test) characterizes crack propagation in the plane of bond created during repair. In the second test the resistance to shear is a measure of adhesion strength.

• Earthquakes and Structures
• /
• 제15권2호
• /
• pp.165-178
• /
• 2018

The aim of this study is to investigate the efficiency of using threaded rods and steel profiles to produce a steel confining system for rehabilitation of damaged concrete corbels for the first time in literature. Some of the specimens were repaired by crack repair epoxy before being confined for further enhancement. A total of 19 two sided damaged corbels were used in the study with different mechanical properties and parameters but similar dimensions. The differences were in rehabilitation style, shear span, fiber percentage, reinforcement steel diameter, and concrete strength. The rehabilitated specimens were loaded with vertical load until failure. Four different configurations were used in the investigation. Test results show that the proposed rehabilitation technique is effective to enhance the load capacity of the corbels and to improve their ductility. Moreover, new formulations were proposed to calculate the load capacity of the rehabilitated corbels. A good fit was observed between numerical and experimental results.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1996년도 봄 학술발표회 논문집
• /
• pp.323-327
• /
• 1996

Reinforced concrete(R/C) structures need repair and rehabilitation due to the deterioration such as a crack, spalling and disintergration. Numerous repair materials which are currently used in construction fields without any regulation are examined in terms of their serviceabilities and effectiveness. In this paper section of existing R/C beams are enlarged with repair materials, that is, epoxy, latex or premix. And then they are strengthened with rebar, steel poate of CFRP on the tension face. Structural behaviors of strengthened beams are investigated both statically and dynamically and they are compared with each. This paper summarizes the overall research plan.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 봄 학술발표회 논문집
• /
• pp.1017-1022
• /
• 2003

The hydraulic structures such as aqueduct tunnels and the drainage canal of the hydroelectric power plant in Japan are almost old. Therefore, the concrete surface of the aqueduct tunnel has received damage by wear-out and the crack, etc. This study was to develop repair mortar mixed a coal ash coarse powder by using two kinds of high early strength cements. As a result, the repair mortar was obtained by substituting the EF cement (maid in Japan) and the MT cement (maid in South Korea) at a rate of 60:40, and substituting the coal ash 30% and the mixing rate 35% of the artificial aggregate for natural fine aggregate.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 봄학술 발표회 논문집(II)
• /
• pp.269-272
• /
• 2005

Epoxy resins are gradually becoming some of the most important and versatile polymers in modem civil engineering. Because epoxy resins have some unigue properties, such as toughness, versatility of viscosity and curing conditions, good handling characteristics, high adhesive strength, inertness, low shrinkage compared to most other thermo-setting resins and concrete, and resistance to chemicals, they have found many applications in construction castings, repair materials, road or bridge deck pavements, coatings, and as structural or non structural adhesives. In this applications, epoxy resins are widely used for polymer concretes, grouting materials, injection glues, and sealants. In this paper, characteristics of deformation of repair material after repaired have been investigated by viscosity of repair material and the width of crack. It is believed that flexural strength of epoxy resin with low viscosity is high because tensile strength is high and elongation at break is low, fracture energy is low.