• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.12
• /
• pp.1198-1204
• /
• 2013

As a microwave near field probe for near field scanning optical microscope(NSOM) system, H-shaped(ridge type) small aperture is proposed and its performances from the viewpoints of the transmission efficiency(transmission cross section) and spatial confinement(beam spot size) are compared with those of the previous narrow rectangular aperture type. While the transmission efficiencies are comparable to each other for the two structures, the transmitted beam spot size for the proposed H-shaped aperture is much smaller than that for the previous rectangular aperture. This strong point of the H-shaped aperture is expected to significantly improve near-field optical applications such as optical data storage, nanolithography and nanomicroscopy. It is also observed that the transmission efficiency can be improved if the coupling aperture is implemented in the type of the transmission cavity.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.1
• /
• pp.20-23
• /
• 2018

In this work, an aperture-coupled patch array antenna with wideband characteristics was designed and arrayed in a $4{\times}1$ S-band. The designed antenna structure consists of two layers, and it possesses wideband characteristics achieved using coupling between the two layers. The first layer is comprised of four radiation patches and the second layer has an aperture and a ground plane. The antenna structure possesses 15 % wideband characteristics and the center frequency is at 3.2 GHz. A phase shifter was added to the array antenna to enable beam steering. The proposed phase array antenna was fabricated and measured. Our proposed design enables beam steering up to $35^{\circ}$.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.12
• /
• pp.3205-3214
• /
• 1996

In this paper, the microstrip phased array antennas with coupling-slots for the base station of mobile communication is proposed and anlyzed with accurate analysis method which is based on both reciprocity principle and full-wave analysis. The basis functions used for the numerical analysis are determined depending upon the accuracy, convergence properties of the solution, and the computation time. The patch uses 3 EB mode and the slot uses IPWS mode. The designed phased array antenna has 8 slot-coupled microstrip patch array elements and the beam scanning capability is obtained by using the 4-bit PIN-diode phase shifters as switching devices which are consisted of the loaded line phase shifters for 30.deg. and 60.deg. and the reflection type phase shifters for 90.deg. and 180.deg. repectively. The 4-bits phase shifters which aremade by connecting each phase shifter have about 2.deg.-3.deg. phase errors and their insertion loss are about 3dB for each phase state. The fabricated 8-element phased array antenna with 4-bits phase shifters provides 12.deg.-14.deg. beamwidths depending on the scanning angle and is capable of scanning its beam to .+-.45.deg. with 9.deg. intervals, and the gain 12dBi. The overall results show that the slot-coupled phased array antenna has great advantages of wideband, high gain and reduced spurious radiation. Also, the antenna can be made small and thin. Furthermore, the scanning property of this antenna allows for its application in several areas, such as mobile communication system and PCS.

• Journal of the Korea Concrete Institute
• /
• v.20 no.3
• /
• pp.345-356
• /
• 2008

In the previous study, direct inelastic strut-and-tie model (DISTM) was developed to perform inelastic design of reinforced concrete members by using linear analysis for their secant stiffness. In the present study, for convenience in design practice, the DISTM was further simplified so that inelastic design of reinforced concrete members can be performed by a run of linear analysis, without using iterative calculations. In the simplified direct inelastic strut-and-tie model (S-DISTM), a reinforced concrete member is idealized with compression strut of concrete and tension tie of reinforcing bars. For the strut and tie elements, elastic stiffness or secant stiffness is used according to the design strategy intended by engineer. To define the failure criteria of the strut and tie elements, concrete crushing and reinforcing bar fracture were considered. The proposed method was applied to inelastic design of various reinforced concrete members including deep beam, coupling beam, and shear wall. The design results were compared with the properties and the deformation capacities of the test specimens.

• Korean Journal of Optics and Photonics
• /
• v.22 no.1
• /
• pp.5-9
• /
• 2011

There are technical difficulties in measuring the numerical apertures of multi-mode gradient-index plastic optical fibers (GI-POFs) due to their strong speckle noise originating from dopants, non-uniformity of gradient-index profile, and multi-mode interference. Therefore, we propose a new method of obtaining the numerical aperture by controlling the size of the incident laser beam and measuring the numerical aperture of GI-POF. The results show that we can get a value for the numerical aperture of GI-POF very similar to that measured by the conventional method. We can also obtain the optimum launching condition of input beam and maximum coupling efficiency.

• Steel and Composite Structures
• /
• v.25 no.1
• /
• pp.117-126
• /
• 2017

The component method is an analytical approach for investigating the moment-rotation relationship of steel connections. In this study, the component method was improved from two aspects: (i) load analysis of mechanical model; and (ii) combination of spring elements. An optimized component method with more reasonable component models, spring arrangement position, and boundary conditions was developed using finite element analysis. An experimental testing program in two major-axis and two minor-axis connections under symmetrically loading was carried out to verify this method. The initial rotational stiffness obtained from the optimized component method was consistent with the experimental results. It can be concluded that (i) The coupling stiffness between column and beam flanges significantly affects the effective height of the tensile-column web. (ii) The mechanical properties of the bending components were obtained using an equivalent t-stub model considering the bending capacity of bolts. (iii) Using the optimized mechanical components, the initial rotational stiffness was accurately calculated using the spring system. (iv) The characteristics of moment-rotation relationship for beam to column connections were effectively expressed by the SPRING element analysis model using ABAQUS. The calculations are simpler, and the results are accurate.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.4
• /
• pp.65-71
• /
• 2023

In this paper, the design, fabrication and verification steps of an electronically scanned array antenna(AESA) for a photonics-based Ku-band FMCW radar system is described. The presented system consists of a transmitter and a receiver respectively, which has a same antenna in the transceiver. The designed antenna has 2×8 array configuration and operates at Ku-band. The VSWR(Voltage Standing Wave Ratio) of each 16-radiators and the coupling power between radiators is measured. Also, in order to minimize the radar system damage because of handover power from the transmitter antenna to the receiver antenna when the transmitter works, the isolation between the transmitter antenna and the receiver antenna is optimized by test. As a result, beamwidth, side lobe level and beam steering characteristic are obtained by synthesizing each radiator pattern measurement data after each beam pattern of 16-radiators is measured in the near-field chamber.

• Advances in nano research
• /
• v.16 no.5
• /
• pp.473-487
• /
• 2024

The current study employs the nonlocal Timoshenko beam (NTB) theory and von-Kármán's geometric nonlinearity to develop a non-classic beam model for evaluating the nonlinear free vibration of bi-directional functionally-graded (BFG) nanobeams. In order to avoid the stretching-bending coupling in the equations of motion, the problem is formulated based on the physical middle surface. The governing equations of motion and the relevant boundary conditions have been determined using Hamilton's principle, followed by discretization using the differential quadrature method (DQM). To determine the frequencies of nonlinear vibrations in the BFG nanobeams, a direct iterative algorithm is used for solving the discretized underlying equations. The model verification is conducted by making a comparison between the obtained results and benchmark results reported in prior studies. In the present work, the effects of amplitude ratio, nanobeam length, material distribution, nonlocality, and boundary conditions are examined on the nonlinear frequency of BFG nanobeams through a parametric study. As a main result, it is observed that the nonlinear vibration frequencies are greater than the linear vibration frequencies for the same amplitude of the nonlinear oscillator. The study finds that the difference between the dimensionless linear frequency and the nonlinear frequency is smaller for CC nanobeams compared to SS nanobeams, particularly within the α range of 0 to 1.5, where the impact of geometric nonlinearity on CC nanobeams can be disregarded. Furthermore, the nonlinear frequency ratio exhibits an increasing trend as the parameter µ is incremented, with a diminishing dependency on nanobeam length (L). Additionally, it is established that as the nanobeam length increases, a critical point is reached at which a sharp rise in the nonlinear frequency ratio occurs, particularly within the nanobeam length range of 10 nm to 30 nm. These findings collectively contribute to a comprehensive understanding of the nonlinear vibration behavior of BFG nanobeams in relation to various parameters.

• Journal of the Korean Magnetics Society
• /
• v.18 no.5
• /
• pp.180-184
• /
• 2008

The relation of ferromagnet anisotropic magnetization and the antiferromagnet atomic spin configuration has been investigated for variously angles of unidirectional deposition magnetic field of FeMn layer in Corning glas/Ta(5 nm)/NiFe(7 nm)/FeMn(25 nm)/ Ta(5 nm) multilayer prepared by ion beam deposition. Three unidirectional deposition angles of FeMn layer are $0^{\circ},\;45^{\circ}$, and $90^{\circ}$, respectively. The exchange bias field ($H_{ex}$) obtained from the measuring easy axis MR loop was decreased to 40 Oe in deposition angle of $45^{\circ}$, and to 0 Oe in the angle of $90^{\circ}$. One other side hand, $H_{ex}$ obtained from the measuring hard axis MR loop was increased to 35 Oe in deposition angle of $45^{\circ}$, and to 79 Oe in the angle of $90^{\circ}$. Although the difference of uniderectional axis between ferromagnet NiFe and antiferromagnet FeMn was 90o, the strong antiferromagnetic dipole moment of FeMn caused to rotate the weak ferromagnetic dipole moment of NiFe in the interface. This result implies that one of origins for exchange coupling mechanism depends on the effect of magnetic field angle during deposition of antiferromgnet FeMn layer.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.12
• /
• pp.1327-1336
• /
• 2012

In this paper, the dual-faced monopole antenna, which is arranged by numerous rectangular ring patches in sequence for the multi-bands is proposed. The ring type structure of the patch can be increased the bandwidth. Therefore the bandwidth and beam width are improved by using multiple arrayed patches. When the ring type patches are inserted serially, the resonance frequencies are occurred by the current flow from the first ring patch. It is possible because the gap between the patches is very narrow. In addition, if the patches are composed on the same plane as the feed-line, fabrication could be very difficult because the gap between the patches is extremely narrow. The thickness and permittivity of the antenna, moreover, are very important parameters because both sides of the substrate are used. We finally found the optimal thickness and permittivity to generate the coupling effect by simulation. All patches are consisted of 4-steps which the patch size was decreased 85 % by each step. In conclusion, the resonant frequency bands are 1.75~2.6 GHz(850 MHz), 3.24~3.46 GHz(220 MHz), 3.8~4.0 GHz(200 MHz), and 4.4~4.9 GHz(500 MHz).