• Journal of electromagnetic engineering and science
• /
• v.10 no.3
• /
• pp.92-98
• /
• 2010

A new wideband bandstop filter(BSF) with a sharp roll-off characteristic is introduced in a stripline structure in this paper. The BSF consists of two sections: the first is two capacitively coupled $\lambda/4$ short-circuited lines with opposite ground positions, while the second is a capacitively coupled $\lambda/4$ short-circuited line. The BSF provides three transmission zeros within the stopband and better than 22 dB rejection over the whole wireless local area network (WLAN) band from 5.15 to 5.825 GHz. The BSF, cascaded to an U.S. ultra-wideband(UWB: 3.1~10.6 GHz) band-pass filter(BPF), is simulated with HFSS and realized with low-temperature co-fired ceramic(LTCC) green tape with a dielectric constant of 7.8. The measurement results agree well with the HFSS simulation results. The size of the UWB BPF including the BSF is $3{\times}6.3\times0.45\;mm^3$.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.12
• /
• pp.1-11
• /
• 1998

A line profile synthesis method is presented that minimizes the nearest-neighbor crosstalk peak level for high-speed pulse transmission in multi-coupled microstrip signal buses. We adopted the optimization technique for the reflected wave control on bus lines resulting in increasing the average spacing between strip conductors, since in a parallel-conductor bus the crosstalk energy is concentrated at the nearest neighbors of the driven line. The generalized S-matrix technique is applied for the input and output waveform prediction, and crosstalk characteristics of various nonuniform lines synthesized for increasing the average spacing are analyzed by comparing each other. Simulation results demonstrate that the Chebyshev taper with dips is adequate to significantly minimize the crosstalk peak level under the satisfactory waveform integrity since the profile is oriented to evenly reflect significant pulse spectra within the frequency range of pulse.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.8
• /
• pp.61-67
• /
• 2010

A characterization procedure for analyzing symmetric coupled MIS(Metal-Insulator-Semiconductor) transmission line is used the same procedure as a general single layer symmetric coupled line with perfect dielectric substrate from the extraction of the characteristic impedance and propagation constant for even- and odd-mode. In this paper, an analysis for a new substrate shielding symmetric coupled MIS structure consisting of grounded crossbar at the interface between Si and SiO2 layer using the Finite-Difference Time-Domain (FDTD) method is presented. In order to reduce the substrate effects on the transmission line characteristics, a shielding structure consisting of grounded crossbar lines over time-domain signal has been examined. Symmetric coupled MIS transmission line parameters for even- and odd-mode are investigated as the functions of frequency, and the extracted distributed frequency-dependent transmission line parameters and corresponding equivalent circuit parameters as well as quality factor for the new MIS crossbar embedded structure are also presented. It is shown that the quality factor of the symmetric coupled transmission line can be improved without significant change in the characteristic impedance and effective dielectric constant.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.12
• /
• pp.1283-1291
• /
• 2003

Nonuniform transmission lines(NTLs) with the desired frequency response can be realized by synthesizing the potential from the coupled mode Zakharov-Shabat(ZS) equation in the one-dimensional inverse scattering problem. In this study, an efficient synthesis method using the ZS equations is presented for NTLs with arbitrarily specified reflection coefficients which take the restricted potential. This method lessens the line length which plague conventional design schemes using specific windows for reflection coefficients. Furthermore solving the ZS inverse transform problem is simplified by adopting the successive approach instead of the conventional iterative method. The proposed method is compared with the conventional method using specific windows by applying to design of dispersive NTL filters, and verified by two-port analysis through the chain matrix.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.6
• /
• pp.529-534
• /
• 2002

Recently, As the higher frequency in clock of digital system being demanded and the density of circuits gets high for purpose of making light and minimizing system, the study for solution of digital signal distortion being interested. In this paper, the distortion of square pulse caused by dispersion as it propagates along a single microstrip line and crosstalk between lines on the Multi-Transmission Lines (MTL) is investigated. The dispersion and crosstalk of pulse signals is analyzed regarding to the structure of transmission line such as relative permittivity, substrate height, strip width of the microstrip line and pulse width of signal pulse.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.1
• /
• pp.1-10
• /
• 1999

In this paper, a method of canceling and suppressing differential-mode crosstalk-noise signals caused by non-uniform coupling between two transmission lines in UTP(Unshielded Twisted Paris) modular jacks is discussed. Differential-mode crosstalk-noise signals in balanced transmission lines in UTP modular jacks were suppressed by inserting auxiliary capacitance between balanced transmission line pairs which are located closely enough to be effectively coupled each other. To verify the effectiveness of the inserted capacitances, precisely calculated auxiliary capacitances were applied to 10 pin modular jacks which are used in local area networks at 100 Mb/s with unshielded twisted pair-cables. The NEXT(Near-End Crosstalk) losses were measured to prove its applicability.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.5
• /
• pp.510-515
• /
• 2011

In this paper, an artificial transmission line coupler with slotted-triangular patches, which is compact and spacesaving structure, is proposed. The proposed structure has specific features of not only convenience for adjusting the characteristic impedance and the phase of its coupled line by varying the lengths of the slots of the artificial transmission lines in designing a coupler but also the maximized coupling value at less than ${\lambda}$/4 electrical length so that it can be designed in compact and small dimensions, while conventional coupled line couplers are generally limited in compact and miniaturized designs by their ${\lambda}$/4 transmission lines. A fabricated 15 dB test-coupler at 2.4 GHz band by proposed design method shows good agreement with theory and simulation.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.4
• /
• pp.585-590
• /
• 1993

A wide passband filter consisting of 3-stage ssymmetrical coupler can be realized, where the admittance inverter parameters in equivalent circuit of asymmetrical coupled microstrip lines are given as a function of a fundamental design parameter of a bandpass filter. An experimental filter was designed over 22 percend bandwidth centered at 9GHz and optimized using Super-Compact. Measured forward transmission and forward reflection closely matched design data but measured insertion loss was slightly higher (0.7dB) than the designed value.

• ETRI Journal
• /
• v.43 no.1
• /
• pp.133-140
• /
• 2021

Herein, we present a compact transversal bandpass filter (BPF) with an extremely wide upper stopband and multiple transmission zeros (TZ). Three signal transmission paths with shorted stubs and open-coupled lines allow signal transmission from input port to output port. Two resonant modes can be excited simultaneously and managed easily for bandpass response. Eleven TZs are achieved via transmission path cancelation; an extremely wide upper stopband with an attenuation level better than -12 dB is achieved up to 11.7 f0, where f0 is the center frequency (CF). In addition, bandwidth and CF can be controlled by adjusting electrical lengths. For proof of concept, a wideband BPF centered at 1.04 GHz with 3 dB fractional bandwidths of 49.2% was designed, fabricated, and evaluated. The overall circuit measures 0.045λg × 0.117λg; good agreement was observed between the measured and simulated results.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.2
• /
• pp.62-65
• /
• 2017

In this paper, three DC Block designs are presented which efficiently meet the need of modern-day compactsize wireless communication systems. As one of the important parts of a complete system design, the proposed microstrip-based DC block with coupled transmission lines efficiently attenuates unwanted frequencies that cause damage to the system. The compact-sized DC block structures are created by incorporating an extended coupled-line section with a radial stub, an enveloped coupled-line section, and using alternate up-down meandering techniques. The structures are analyzed for the L-Band using a high-resistive silicon substrate. At a resonating frequency of 1.575 GHz, the designed DC Block structures have a return loss better than -10 dB, an insertion loss of around -1 dB, and also possess wide pass-band characteristics.