• Structural Engineering and Mechanics
• /
• 제57권4호
• /
• pp.641-656
• /
• 2016

Reinforced concrete frame buildings with masonry infill walls are one of the most popular structural systems in the world. In most cases, the effects of masonry infill walls are not considered in structural models. The results of earthquakes show that infill walls have a significant effect on the seismic response of buildings. In some cases, the buildings collapsed as a result of the formation of a soft story. This study developed a simple method, called corner opening, by replacing the corner of infill walls with a very flexible material to enhance the structural behavior of walls. To evaluate the proposed method a series of experiments were conducted on masonry infill wall and reinforced concrete frames with and without corner openings. Two 1:4 scale masonry infill walls with and without corner openings were tested under diagonal tension or shear strength and two RC frames with full infill walls and with corner opening infill walls were tested under monotonic horizontal loading up to a drift level of 2.5%. The experimental results revealed that the proposed method reduced the strength of infill wall specimens but considerably enhanced the ductility of infill wall specimens in the diagonal tension test. Moreover, the corner opening in infill walls prevented the slid shear failure of the infill wall in RC frames with infill walls.

• 한국지반신소재학회논문집
• /
• 제12권2호
• /
• pp.55-66
• /
• 2013

본 논문은 다양한 굴착조건으로 모형실험을 실시하여 흙막이 벽체 우각부 구간의 거동에 대해 분석하였다. 실험대상 지반은 느슨한 상태의 모래지반으로 구성되었다. 실험의 시공조건은 우각부 길이, 근입깊이, 버팀대의 시공 유 무 등으로 구분하고 굴착은 총 4단계로 굴착하였다. 각각의 시공 및 굴착조건에 대해 모형토조 내 설치된 계측기를 이용하여 벽체변위 및 지표침하를 중점적으로 분석함으로써 우각부 모서리의 거동특성을 규명하였다. 실험결과 우각부의 길이가 길어질수록 벽체변위와 지표침하가 증가되어 직선구간에 비해 우각부구간이 구조적으로 불안한 구간으로 분석되었다. 근입깊이가 길어질수록 우각부 모서리구간의 지표침하가 약 40% 억제되는 것으로 나타나 설계 시 예상치보다 근입깊이를 증가시켜 적용하는 것이 안정성 확보에 유리하였다. 버팀대 추가 설치하여 우각부 모서리구간의 거동을 분석한 결과 최대지표침하는 약 40%, 최대수평변위는 약 30%의 감소효과가 있어 설계 시 우각부 모서리 구간에 근입깊이의 증가와 함께 버팀대를 추가 설치하는 방안이 안정성 확보에 효과적이었다.

• 건축역사연구
• /
• 제21권2호
• /
• pp.7-20
• /
• 2012

As the corner of wooden pagoda forms the roof by closely bordering left and right eaves on the various purlins and angle rafters, it is designed for every face to be recognized as front whose structure system increases load to bear proportionally. The corner of wooden pagoda is inseparable with the corner bracket set as it becomes stable thanks to the corner bracket set structurally and load burden under restrained structure makes the corner bracket set really important. Accordingly, this study could figure out some facts by analyzing corner bracket sets of Palsangjeon of Beobjusa Temple in Korea, Seokgatap of Bulgungsa Temple in China and Ojungtap of Beobryungsa Temple in Japan which were constructed with pure wooden structure. This study demonstrated that corner bracket set played a pivotal role in keeping balance of concentrated load of corner (corner of opening) in each floor that contributed to the stability of wooden pagoda structurally despite multiple duplications of floors and also figured out the outfit of corner bracket set was subject to the floor type and the cross section of Gongpo installed on top of Pyeongju. Wooden pagodas in 3 countries were two floor types of octagon and square, and employed different connection method between upper and lower floors. The difference between floor and duplication method determines the method of corner, but even different methods were sufficient to have entirety in every side by completing dynamic principle of corner bracket set even though old method had to solve the problem of concentrated load and it also confirms that it was essential Gongpo to prevent any deformation of corner.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
• /
• pp.378-381
• /
• 2006

Test results of four reinforced concrete two-span continuous deep beams are summarized. Main variables were the configuration of web opening reinforcement. Shear span-to-overall depth ratio and the size of the web opening were fixed by 1.0 and 0.5 a $\times$ 0.2 h, respectively. To control diagonal crack and enhance strength, it can be recommended that diagonal reinforcement crossing the crack plane joining between loading points and corner of openings should be provided.

• 국제초고층학회논문집
• /
• 제8권4호
• /
• pp.303-311
• /
• 2019

The effectiveness of aerodynamic modification to reduce wind loadings has been widely reported. However, most of previous studies have been investigated dynamic forces and pressure distributions on tall buildings with various unconventional configurations. This study was investigated dynamic characteristics and aerodynamic instability of super-tall buildings with unconventional configurations through extensive aeroelastic model experiments. Seventeen types of supertall building models were considered such as basic and corner modification with corner cut, chamfered, oblique opening, tapered, inversely tapered, bulged, helical with twist angles of $90^{\circ}$, $180^{\circ}$, $270^{\circ}$, $360^{\circ}$ and composite with $360^{\circ}$ helical & corner cut, 4-tapered & $360^{\circ}$ helical & corner cut, setback & corner cut, setback & $45^{\circ}$ rotate. As a result, aerodynamic characteristics of helical models with single modification are superior to those of other models with single modification. However, effect of twist angle for helical model is negligible. Further, the 4-tapered & $360^{\circ}$helical & corner cut model is most effective in reducing the along- and across-wind fluctuating displacement responses in all of experimental models.

• Steel and Composite Structures
• /
• 제18권3호
• /
• pp.641-657
• /
• 2015

Application of reduced web beam section (RWBS) as a sacrificial fuse element has become a popular research field in recent years. Weakening of beam web in these connections may cause local web buckling around the opening area which can affect cyclic behavior of connection including: maximum load carrying capacity, strength degradation rate, dissipated energy, rotation capacity, etc. In this research, effect of local web buckling on the cyclic behavior of RWBS connections is investigated using finite element modeling (FEM). For this purpose, a T-shaped moment connection which has been tested under cyclic loading by another author is used as the reference model. Fracture initiation in models is simulated using Cyclic Void Growth Model (CVGM) which is based on micro-void growth and coalescence. Included in the results are: effect of opening corner radii, opening dimensions, beam web thickness and opening reinforcement. Based on the results, local web buckling around the opening area plays a significant role on the cyclic behavior of connection and hence any parameter affecting the local web buckling will affect entire connection behavior.

• Structural Engineering and Mechanics
• /
• 제31권6호
• /
• pp.679-696
• /
• 2009

The paper aims at analyzing the stress distribution around an underground opening that is subjected to non-symmetrical surface loading with emphasis on opening shapes with sharp corners and the stress concentrations developed at these locations. The analysis is performed utilizing the BIE method coupled with the Neumann's series. In order to implement this approach, the special recurrent relations for half plane were proven and the modified Shanks transform was incorporated to accelerate the series convergence. To demonstrate the capability of the developed approach, a horseshoe shape opening with sharp corners was investigated and the location and magnitude of the maximum hoop stress was calculated. The dependence of the maximum hoop stress location on the parameters of the surface loading (degree of asymmetry, size of loaded area) and of the opening (the opening height) was studied. It was found that the absolute magnitude of the maximum hoop stress (for all possible surface loading locations) is developed at the roof points when the opening height/width ratio is relatively large or when the pressure loading area is relatively narrow (compared to the roof arch radius), and contrarily, when the opening height/width ratio is relatively small or when the surface pressure is applied to a relatively wide area, the absolute magnitude of the maximum hoop stress is developed at the bottom sharp corner points.

• KIEAE Journal
• /
• 제15권1호
• /
• pp.139-146
• /
• 2015

This is an experimental study on the engineering characteristics of perforated reinforced concrete beams with shells. In the material matter of this study, the water cement ratio put 60%, the ratio of substitution of oyster shells to fine aggregate 30%. And in the structural matter, the form of opening put circle and square, the size of opening as the radius and the length of it changed from one to three times of the beam depth with a change presence and absence of reinforced steel around opening. All thirteen reinforced concrete beam tests composed one standard beam and twelve six beams with the circle and square opening were tested in shear strength under two points loading and compared and analyzed the characteristics of test beams under the same conditions one another. The results of the study showed as followed. 1) The initial crack load value of the opening test beams is similar the standard beam but the maximum load value decreased with increase in proportion of the opening size, in the square opening than the circle opening and in the absence than the presence of reinforced steel. 2) As the difference between the circle opening and the square opening beams is represented 2.17~9.8% in the maximum load value and the load capacity of the square opening suddenly decrease than it of the circle opening, it is judged because of the shortage of concrete section, the concentration of the stress in the corner of the square opening and material influence of shell substitution. 3) The failure figure such as the pattern of the crack and so on is represented brittle failure as the opening size is the bigger and the ratio of substitution is higher because of the lack material properties.

• Wind and Structures
• /
• 제32권2호
• /
• pp.105-114
• /
• 2021

This paper describes a wind tunnel test on a 1:25 scale model of TTU building with several adjustable openings in order to comprehensively study the characteristics of fluctuating internal pressures, especially the phenomenon of the increase in fluctuating internal pressures induced by tangential flow over building openings and the mechanism causing that. The effects of several factors, such as wind angle, turbulence intensity, opening location, opening size, opening shape and background porosity on the fluctuating internal pressures at oblique wind angles are also described. It has been found that there is a large increase in the fluctuating internal pressures at certain oblique wind angles (typically around 60° to 80°). These fluctuations are greater than those produced by the flow normal to the opening when the turbulence intensity is low. It is demonstrated that the internal pressure resonances induced by the external pressure fluctuations emanating from flapping shear layers on the sidewall downstream of the windward corner are responsible for the increase in the fluctuating internal pressures. Furthermore, the test results show that apart from the opening shape, all the other factors influence the fluctuating internal pressures and the internal pressure resonances at oblique wind angles to varying degrees.

• Journal of Welding and Joining
• /
• 제27권5호
• /
• pp.74-80
• /
• 2009

The membrane of the LNG carriers consists of thin strips of INVAR(Fe-36%Ni) steel plates, and the junction between INVAR strips is fabricated by welding. Thousands of the raised edge joints, regularly spaced, are located around all the side of the tank corner near the transverse bulkhead, and TIG welding is manually made on the top of the raised edges. Since the thickness of all the laminated edge plies is extremely thin and the weld position is under a bad accessibility, highly skilled workers are required to perform welding relatively for a long welding time. An alternative scheme for the corner membrane fabrication is proposed in the study to improve the installation workability and thus productivity. The scheme replaces the welded edges with the preformed corrugation ones. A panel strip with regularly-spaced corrugations is installed at the corner instead of the individual flat strip of which edge is vertically raised to be welded with the adjacent strip. In the study, a series of the evaluation on the corrugated edge members was performed to assess the applicability to the real LNG carrier fabrication. Opening displacement at the raised edge was experimentally examined. Elastic stiffness regressed from the displacement was nearly same in both edge types. Edge displacement and local stresses were calculated under hydrostatic pressure and temperature change due to liquefied cargo. Fatigue test was performed on both corrugated and welded edge specimens consisting of two or five plies of invar strips. Fatigue strength of the corrugated specimens was not less than that of the welded specimens.