• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.861-863
• /
• 1998

As-casted high nitrogen alloys (Fe-25%Mn-12%Cr-1%Ni) have been investigated to study core material. Nitrogen concentration in molten alloys was increased with increasing the square root of nitrogen gas pressure in melting chamber. This result can be explained by Sievert's law. Nitrogen that dissolved as a interstital solid solution element in austenite stainless steel increased lattice parameter and hardness. Electric resistivity($\rho$) was increased with increasing nitrogen concentration and was about $80{\mu}{\Omega}cm$ at room temperature. Coefficient of linear thermal expansion of the nitrogen steel was about $22{\times}10^{-6}/^{\circ}C$.

• Geophysics and Geophysical Exploration
• /
• v.13 no.1
• /
• pp.69-79
• /
• 2010

In order to reduce leakage from a reservoir, a large amount of cement milk (grout) was injected from boreholes drilled around the shores of the reservoir, and monitored to establish the infiltration of cement milk into the bedrock under the reservoir. From laboratory tests using rock core samples, it was revealed that the resistivity of cement milk is much lower than that of the groundwater at this location. Therefore, it was expected that the resistivity of the zones filled with cement milk would be significantly reduced. Geophysical surveys are expected to be suitable methods to check the effectiveness of grouting in improving the water-retaining performance of a reservoir. DC electrical surveys (seven in total) and two Controlled Source Audio-frequency Magneto-Telluric (CSAMT) surveys were conducted along survey lines in the reservoir to monitor the infiltration of cement milk during the grouting. Extremely low resistivity zones ($10\;{\Omega}m$ or less) were observed in resistivity sections obtained by 2D inversion. The zones are inferred to be fractured zones filled with cement milk. In sections showing the rate of change of resistivity, three zones that showed significant change showed gradual expansion to deeper parts as the grouting progressed. These zones correspond to highly permeable zones detected by Lugeon tests at grout boreholes. We have confirmed that it is possible to measure the resistivity change by DC electrical and CSAMT surveys from the surface of the reservoir. It seems that such monitoring results could be reflected in future grouting plans.

• The Journal of Engineering Geology
• /
• v.31 no.4
• /
• pp.507-522
• /
• 2021

Specific survey objectives often cannot be met using only one geophysical method, as each method's results are influenced by the specific physical properties of subsurface materials. In particular, areas susceptible to geological hazards require investigation using more than one method in order to reduce risks to life and property. Instead of analyzing the results from each method separately, this work develops a four-quadrant criterion for classifying areas of levees as safe or weak. The assessment is based on statistically determined thresholds of seismic velocity (P-wave velocity from seismic refraction and S-wave velocity from multichannel analysis of surface waves) and electrical resistivity. Thresholds are determined by subtracting the standard deviation from the mean during performance testing of this correlation technique applied to model data of four horizontal and inclined fracture zones. Compared with results from the crossplot of resistivity and P-wave velocity, crossplot analysis using resistivity and S-wave velocity data provides more reliable information on the soil type, ground stiffness, and lithological characteristics of the levee system. A loose and sandy zone (represented by low S-wave velocity and high resistivity) falling within the second quadrant is interpreted to be a weak zone. This interpretation is well supported by the N values from standard penetrating test for the central core.

• The Journal of Engineering Geology
• /
• v.8 no.2
• /
• pp.163-173
• /
• 1998

Suite of log analysis techniques consisting of geophysical well log, geological core log, and physical core log have been made to understand the well log responses and to determine the lithology of a test borehole-PABH1 located in Pungam sedimentary basin, Sosok, Hongchon-gun, Kangwon Province. Geological core logging has been precisely made over the cores taken between 64 and 124 meters, and 11 groups of rock types were deduced. Using the core samples divided by 11 groups, geophysical property measurements consisting of resistivity, natural gamma and density were made. Each rock group in the area is shown to have its characteristic physical response from geophysical well log and geophysical core logs. The outstanding physical responses particularly shown from siltstone, coarse sandstone to conglomerate, and granitic gneiss in the area were effectively used as keybeds in correlating the geophysical well logs to the result of geological core logs.

• Journal of Magnetics
• /
• v.19 no.4
• /
• pp.327-332
• /
• 2014

The effect of minor element additions (Ca, Al) on microstructural change and magnetic properties of Fe-Nb-Cu-Si-B alloy has been investigated, in this paper. The Fe-Si-B-Nb-Cu(-Ca-Al) alloys were prepared by arc melting in argon gas atmosphere. The alloy ribbons were fabricated by melt-spinning, and heat-treated under a nitrogen atmosphere at $520-570^{\circ}C$ for 1 h. The soft magnetic properties of the ribbon core were analyzed using the AC B-H meter. A differential scanning calorimetry (DSC) was used to examine the crystallization behavior of the amorphous alloy ribbon. The microstructure was observed by X-ray diffraction (XRD), transmission electron microscope (TEM) and scanning electron microscope (SEM). The addition of Ca increased the electrical resistivity to reduce the eddy current loss. And the addition of Al decreased the intrinsic magnetocrystalline anisotropy $K_1$ resulting in the increased permeability. The reduction in the size of the ${\alpha}$-Fe precipitates was observed in the alloys containing of Ca and Al. Based on the results, it can be concluded that the additions of Ca and Al notably improved the soft magnetic properties such as permeability, coercivity and core loss in the Fe-Nb-Cu-Si-B base nanocrystalline alloys.

• Economic and Environmental Geology
• /
• v.19 no.4
• /
• pp.283-292
• /
• 1986

Finite element method with linear triangular and bilinear rectangular elements is applied to solve the three-dimensional potential distribution due to a point source of current located in or on the surface of the earth containing arbitrary two-dimensional resistivity distribution. The modeling technique developed in this paper is flexible to model conductive inhomogeneity and surface topographies, and more accurate to evaluate surface potentials than the conventional techniques using finite difference method. Since it is possible to reduce nodal points with acceptable accuracy, this modeling technique is very efficient and economic in terms of execution time and core space. A few geologic structures adequate to demonstrate above features are simulated in this paper.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.918-919
• /
• 2015

Because of environmental regulations in emissions control area, the demand for ships to use LNG as fuel is increasing. Orders for domestic shipbuilders to produce LNG carriers are steadily increasing. However, major appliances such as spray pump, main cargo pump and others have been relied on imports. Therefore, development of pump motor using at cryogenic temperature is necessary. Operating temperature of an induction motor is at $-163^{\circ}C$. At this low temperature, the resistivity of a motor coil is quite different from normal ones, and so does the torque characteristics of motor. This paper presents a designing method of a cryogenic induction motor for LNG pump. The variation of resistivity of motor coil is considered in the design process. The heat source such as core-loss, hysteresis-loss and copper-loss are analyzed to prevent the LNG evaporation which may cause the motor failure.

• Journal of Surface Science and Engineering
• /
• v.45 no.6
• /
• pp.242-247
• /
• 2012

Yb-doped ITO (ITO:Yb) films were deposited on unheated non-alkali glass substrates by magnetron cosputtering using two cathodes (DC, RF) equipped with the ITO and $Yb_2O_3$ target, respectively. The composition of the ITO:Yb films was controlled by adjusting the RF powers from 0 W to 480 W in 120 W steps with the DC power fixed at 70 W. The ITO:Yb films had a higher crystallization temperature ($200^{\circ}C$) than that of the ITO films ($170^{\circ}C$), which was attributed to both larger ionic radius of $Yb^{3+}$ and higher bond enthalpy of $Yb_2O_3$, compared to ITO. This amorphous ITO:Yb film post-annealed at $170^{\circ}C$ showed a resistivity of $5.52{\times}10^{-4}{\Omega}cm$, indicating that a introduction of Yb increased resistivity of the ITO film. However, these amorphous ITO:Yb films showed a high etching rate, fine pattering property, and a very smooth surface morphology above the crystallization temperature of the amorphous ITO films (about $170^{\circ}C$). The transmittance of all films was >80% in the visible region.

• Journal of the Korean Magnetics Society
• /
• v.9 no.6
• /
• pp.278-284
• /
• 1999

The effect of TiO$_2$addition has been studied on the power loss, density, initial permeability, resistivity, and microstructure of Mn-Zn ferrites. TiO$_2$addition increased the density of sintered body and decreased of the initial permeability. Activation energy for electron hopping as well as electrical resistivity increased with TiO$_2$addition. The toroidal core sintered at 1150 $^{\circ}C$ with 1.5 wt% of TiO$_2$demonstrated the power loss of 83 mW/㎤ at 1 MHz, 25 mT, 8$0^{\circ}C$. However, the same specimen sintered at 120$0^{\circ}C$ lead to the power loss, 1168 mW/㎤ at 1 MHz, 25 mT, 8$0^{\circ}C$ and developed an exaggerated grain growth.

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.841-845
• /
• 1995

The effect of small addition of Nb on the electrical resistivity and Hall coeffcient of the amorphous $Fe_{83}Zr_{7}B_{10}$ alloy and annealed ones ones below the crystallization temperature were investigated, which has been considered to be suitable for high frequency core material. At room temperature, their resistivities $\rho$ and the spontaneous Hall coeffcients $R_{s}$ are $~1.6\;{\mu}{\Omega}m$ and $~3{\times}10^{-8}m^{3}/As$, respectively. $R_{s}$ and $\rho$ are decreased with increasing temperature from 100 K to room temperature. Side-jump effect was adopted to analyze the effect of the small variation of conentration and annealing. The quantity of $R_{s}/{\rho}^{2}$ at room temperature, which is directly related to the electronic structure of the mother alloy, remained almost a constant except as quenched one as it can be predicted from the side-jump effect. The unexpected temperature dependence of $R_{s}/{\rho}^{2}$ measured at low fields much below Tc is left as a question.