• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.205-208
• /
• 2001

Steady state and transient thermal analysis has been done by a finite element method in a diode of 12kV blocking voltage for microwave oven. The diode was fabricated by soldering ten pieces of 1200V diodes in series, capping a dummy wafer at the far end of diode series, and finally copper wire bonded for building anode and cathode terminal. In order to achieve high voltage and reliability, the edge of each diode was beveled and passivated by resin and epoxy with a thickness of 25$\mu\textrm{m}$ and 3,700$\mu\textrm{m}$, respectively. The chip size, thickness and material properties were very important factor for high voltage diode package. And also, thermal stress value was highest in the edge of diode and solder. So, design of edge in silicon was very important to thermal stress.

• Structural Engineering and Mechanics
• /
• 제77권1호
• /
• pp.103-114
• /
• 2021

Ultra high strength concrete (UHSC) originally proposed by Richards and Cheyrezy (1995) composed of cement, silica fume, quartz sand, quartz powder, steel fibers, superplasticizer etc. Later, other ingredients such as fly ash, GGBS, metakaoline, copper slag, fine aggregate of different sizes have been added to original UHSC. In the present investigation, the combined effect of coarse aggregate (6mm - 10mm) and steel fibers (0.50%, 1.0% and 1.5%) has been studied on UHSC mixes to evaluate mechanical and fracture properties. Compressive strength, split tensile strength and modulus of elasticity were determined for the three UHSC mixes. Size dependent fracture energy was evaluated by using RILEM work of fracture and size independent fracture energy was evaluated by using (i) RILEM work of fracture with tail correction to load - deflection plot (ii) boundary effect method. The constitutive relationship between the residual stress carrying capacity (σ) and the corresponding crack opening (w) has been constructed in an inverse manner based on the concept of a non-linear hinge from the load-crack mouth opening plots of notched three-point bend beams. It was found that (i) the size independent fracture energy obtained by using above two approaches yielded similar value and (ii) tensile stress increases with the increase of % of fibers. These two fracture properties will be very much useful for the analysis of cracked concrete structural components.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.444-445
• /
• 2009

The metallic contact system of silicon solar cell must have several properties, such as low contact resistance, easy application and good adhesion. Ni is shown to be a suitable barrier to Cu diffusion as well as desirable contact metal to silicon. Nickel monosilicide(NiSi) has been suggested as a suitable silicide due to its lower resistivity, lower sintering temperature and lower layer stress than $TiSi_2$. Copper and Silver can be plated by electro & light-induced plating method. Light-induced plating makes use the photovoltaic effect of solar cell to deposit the metal on the front contact. The cell is immersed into the electrolytic plating bath and irradiated at the front side by light source, which leads to a current density in the front side grid. Electroless plated Ni/ Electro&light-induced plated Cu/ Light-induced plated Ag contact solar cells result in an energy conversion efficiency of 16.446 % on $0.2\sim0.6\;{\Omega}{\cdot}cm$, $20\;\times\;20\;mm^2$, CZ(Czochralski) wafer.

• 생태와환경
• /
• 제40권4호
• /
• pp.489-494
• /
• 2007

Transcriptional modulation of metallothionein (MT) during acute metal exposures (cadmium, copper or zinc) was examined in fry of Hemibarbus mylodon, a threatened fish species in Korean peninsula. Viability of H. mylodon fry was most affected by copper exposure (up to 79% of mortality at 1 ppm for 48 hours) and considerably by cadmium exposure (21 to 54% of mortality). On the other hand, Zn showed the least adverse effect on the viability (0 to 13% of mortality) of this species. Based on the semi-quantitative RT-PCR analysis, the stimulation of MT mRNA in response to metal exposures followed generally in a dose-dependent fashion where cadmium was the most potent inducer for the induction of MT transcripts in fry (up to more than 5-fold) while the lowest response was observed in zinc-exposed group (2-fold at maximum). From the exposure using environmentally realistic doses of cadmium (0 to 0.05 ppm for 24 hours), MT expression at mRNA level was also sensitively modulated toward upregulation up to more than 3-fold as relative to non-exposed control. Results from the present study would be a good basis for understanding the adaptive capacity and stress physiology of this endangered fish species during metal pollution.

• 한국정밀공학회지
• /
• 제18권5호
• /
• pp.90-97
• /
• 2001

An electronic speckle pattern interferometry (ESPI) system for measuring tensile properties under micro-tensile testing has been developed. The system consists of an optical system and an image processing system. In the optical system, optical components for measurement of in-plane deformation are arranged on the path of He-Ne laser. In the image processing system, the window-based program for acquiring speckle pattern interferometric image was developed and deformation in a small specimen is continuously evaluated during the test. Using this system, tensile strain of copper foil was measured during tensile testing. Tensile specimen had the thickness and width of 22 and 500 ${\mu}{\textrm}{m}$, respectively. Tensile properties, including the elastic modulus, yielding strength and tensile strength, of the copper were evaluated and also plastic exponent and coefficient in the Ramberg-Osgood relationship were evaluated from the stress-strain curve.

• Journal of Magnetics
• /
• 제10권2호
• /
• pp.48-51
• /
• 2005

The spin transfer induced magnetization switching has been reported to occur in magnetic multilayer structures whose scope usually consists of one stack of ferromagnetic / non-ferromagnetic / ferromagnetic (F / N / F) materials. In this work, it is shown that: 1) Copper used as a buffer layer between the free Co and the Au cap-layer can clearly increase the probability to get the spin transfer induced magnetization switching in a simple spin valve Co 11 / Cu 6/ Co 2 (nm); 2) Furthermore, when Ruthenium is simultaneously applied as a buffer layer on the Si-substrate, the critical switching currents can be reduced by $30\%$, and the absolute resistance change delta R $[{\Delta}R]$ of that stack can be enlarged by $35\%$. The enhancement of the spin transfer induced magnetization switching can be ascribed to a lower local stress in the thin Co layer caused by a better lattice match between Co and Cu and the smoothening effect of Ru on the thick Co layer.

• 한국재료학회지
• /
• 제23권1호
• /
• pp.1-6
• /
• 2013

A simple thermal oxidation of Cu thin films deposited on planar substrates established a growth of vertically aligned copper oxide (CuO) nanorods. DC sputter-deposited Cu thin films with various thicknesses were oxidized in environments of various oxygen partial pressures to control the kinetics of oxidation. This is a method to synthesize vertically aligned CuO nanorods in a relatively shorter time and at a lower cost than those of other methods such as the popular hydrothermal synthesis. Also, this is a method that does not require a catalyst to synthesize CuO nanorods. The grown CuO nanorods had diameters of ~100 nm and lengths of $1{\sim}25{\mu}m$. We examined the morphology of the synthesized CuO nanorods as a function of the thickness of the Cu films, the gas environment, the oxidation time, the oxidation temperature, the oxygen gas flow rate, etc. The parameters all influence the kinetics of the oxidation, and consequently, the volume expansion in the films. Patterned growth was also carried out to confirm the hypothesis of the CuO nanorod protrusion and growth mechanism. It was found that the compressive stress built up in the Cu film while oxygen molecules incorporated into the film drove CuO nanorods out of the film.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2016년도 추계학술대회 논문집
• /
• pp.135-135
• /
• 2016

Recently flexible electrode materials have attracted attention in various electrical devices. In general, copper(Cu) is widely used electrical conductive material. However, Cu film showed drastically reduction of electrical conductivities under an applied tensile strain of 10%. These poor mechanical characteristics of Cu have difficulty applying in flexible electronic applications. In this study, mechanical flexibilities of Cu thin film were improved by hybridization with carbon nanotubes(CNTs) and laser sintering. First, thin carbon nanotube films were fabricated on a flexible polyethylene terephthalate(PET) substrate by using ultrasonic spray coating of CNT dispersed solution. After then, physically connected CNT-Cu NPs films were formed by utilizing ultrasonic spray coating of Cu nanoparticles dispersed solution on prepared CNT thin films. Finally, CNT-Cu thin films were firmly connected by laser sintering. Therefore, electrical stabilities under mechanical stress of CNT-Cu hybrid thin films were compared with Cu thin films fabricated under same conditions to confirm improvement of mechanical flexibilities by hybridization of CNT and Cu NPs.

• 한국추진공학회지
• /
• 제19권2호
• /
• pp.29-37
• /
• 2015

본 연구는 케로신 연료를 사용하는 액체로켓엔진에서 발생할 수 있는 연소불안정으로 인하여 파괴될 수 있는 연소기의 손상을 수치적으로 모사하는 해석 모델의 기초연구이다. 연소불안정으로부터 야기 될 수 있는 케로신의 데토네이션은 1단계 아레니우스 식의 화학 반응식을 이용하였고, 구조체는 Johnson-Cook 강성모델을 활용하여 데토네이션으로 인한 금속관의 소성 변형을 모델링하였다. 금속관의 소성 변형에 의해 변화하는 유동장과 구조체의 스트레스를 노즐 형상과 관의 두께변화에 따라 해석하였다.

• Membrane and Water Treatment
• /
• 제10권3호
• /
• pp.231-237
• /
• 2019

Peroxymonosulfate (PMS) in combination with Cu(II) was examined to inactivate E. coli and MS2 coliphage in natural water. The combined system (i.e., the Cu(II)/PMS system) caused a synergistic inactivation of E. coli and MS2, in contrast with either Cu(II) or PMS alone. Increasing the concentration of PMS enhanced the inactivation of E. coli and MS2, but after a certain point, it decreased the efficacy of the microbial inactivation. In the Cu(II)/PMS system, adding reactive oxidant scavengers marginally affected the E. coli inactivation, but the inhibitory effects of copper-chelating agents were significant. Fluorescent assays indicated that the Cu(II)/PMS system greatly increased the level of reactive oxidants inside the E. coli cells. The sequential addition of Cu(II) and PMS inactivated more E. coli than did adding the two simultaneously; in particular, the inactivation efficacy was much higher when Cu(II) was added first. The observations from the study collectively showed that the microbial inactivation by the Cu(II)/PMS system could be attributed to the toxicity of Cu(I) as well as the intracellular oxidative stress induced by Cu(III) or radical species.