• Journal of the Korean Vacuum Society
• /
• v.13 no.3
• /
• pp.120-126
• /
• 2004

A damage-reduced trench was investigated in view of the defect distribution along trench sidewall and bottom using high resolution transmission electron microscopy, which was formed by HBr plasma and additive gases in magnetically enhanced reactive ion etching system. Adding $O_2$ and other additive gases into HBr plasma makes it possible to eliminate sidewall undercut and lower surface roughness by forming the passivation layer of lateral etching. To reduce the RIE induced damage and obtain the fine shape trench corner rounding, we investigated the hydrogen annealing effect after trench formation. Silicon atomic migration on trench surfaces using high temperature hydrogen annealing was observed with atomic scale view. Migrated atoms on crystal surfaces formed specific crystal planes such as (111), (113) low index planes, instead of fully rounded comers to reduce the overall surface energy. We could observe the buildup of migrated atoms against the oxide mask, which originated from the surface migration of silicon atoms. Using this hydrogen annealing, more uniform thermal oxide could be grown on trench surfaces, suitable for the improvement of oxide breakdown.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.3
• /
• pp.295-302
• /
• 2013

The two cross-roll straightening process at room temperature is a manufacturing method for improving the straightness of a drawn wire. The distribution and magnitude of the internal and surface residual stresses of the drawn wire are changed after the wire-drawing process through the two cross-rolls; this also results in a change in the diameter of the drawn wire. The remaining residual stresses of the drawn wire after the wire-drawing dimensional changes were analyzed according to the distance between the rolls, oblique angle between the axes of the roll and the wire, predicted residual stresses, and dimensional change in the final product. The oblique angle between the concave and convex rolls did not affect the residual stresses or dimensional change, but the distance between rolls did.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.30 no.1 s.149
• /
• pp.157-166
• /
• 2006

The human body, which is composed of concave and convex curvatures, makes it difficult to transfer into 2D patterns directly from 3D data. In previous studies. Jeong, et al.(2004) suggested the block method was fester and easier when dealing with the triangular patches of male's upper dress form. Although the block method is useful to make a pattern, the information(area, length, etc.) from a 2D pattern would be different depending on the direction of the block method. As a result horizontal and diagonal block methods were suggested as optimal methods for 2D tight-fitting patterns. These block methods were closer to the original area of the 3D scan data than the vertical block method. The total area of the 2D pattern obtained by the horizontal and diagonal block methods showed little differences. In case of the horizontal and diagonal block methods, the total error of the 2D pattern area ranged from $0.01\%\~0.25\%$. In comparing the length of the 2D pattern with that of the 3D scan data, the obtained 2D pattern was $0.1\~0.2cm$ shorter than the 3D scan data, which was within the acceptable range of errors in making clothes. 3D space distribution images between the body surface and the experimental clothing were also measured and $3\%$ enlargement of the original pattern was verified as the adequate adjustment.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.14 no.3
• /
• pp.267-276
• /
• 2001

On the basis of structural analysis of the radial gate(that is, Tainter gate), this paper focuses on the optimization of the moment distribution according to the location of the arm of the radial gate. In spite of its importance from economical view point, we could hardly find the study on the optimum design of radial gate. Accordingly, the present study identifies the optimum section modulus for a radial arm along with the optimum position for 2 of 3 radial arms with a convex cylindrical skin plate relative to a given radius of the skin plate curvature, pivot point, water depth, ice pressure, etc. These optimum measurements are then compared with previously constructed radial gates. The results indicate that the optimum section modulus vague for a radial arm was appreciably smaller than the previously constructed examples.

• The Korean Journal of Applied Statistics
• /
• v.34 no.6
• /
• pp.863-874
• /
• 2021

In this paper, we propose a post-selection inference procedure for the fused lasso signal approximator (FLSA). The FLSA finds underlying sparse piecewise constant mean structure by applying total variation (TV) semi-norm as a penalty term. However, it is widely known that this convex relaxation can cause asymptotic inconsistency in change points detection. As a result, there can remain false change points even though we try to find the best subset of change points via a tuning procedure. To remove these false change points, we propose a post-selection inference for the FLSA. The proposed procedure applies a permutation test based on CUSUM statistic. Our post-selection inference procedure is an extension of the permutation test of Antoch and Hušková (2001) which deals with single change point problems, to multiple change points detection problems in combination with the FLSA. Numerical study results show that the proposed procedure is better than naïve z-tests and tests based on the limiting distribution of CUSUM statistics.

• Earthquakes and Structures
• /
• v.26 no.2
• /
• pp.131-147
• /
• 2024

Damage caused by an earthquake depends on not just the intensity of an earthquake but also the region-specific construction practices. Past earthquakes in Asian countries have highlighted inadequate construction practices, which caused huge life and property losses, indicating the severe need to strengthen existing structures. Strengthening activities shall be proposed as per the proposed weighting factors, first at the higher weighted members to increase the capacity of the building immediately and thereafter, the other members. Through this study on gravity load-designed (GLD) buildings, relative weights are assigned to each storey and exterior and interior columns within a storey based on their contribution to the energy dissipation capacity of the building. The numerical study is conducted on mid-rise archetype GLD buildings, i.e., 4, 6, 8, and 10 stories with variable storey heights, in the high seismic zones. Non-linear static analysis is performed to compute weights based on energy dissipation capacities. The results obtained are verified with the non-linear time history analysis of 4 GLD buildings. It was observed that exterior columns have higher weightage in the energy dissipation capacity of the building than interior columns up to a certain building height. The damage in stories is distributed in a convex to concave parabolic shape from bottom to top as building height increases, and the maxima location of the parabola shifts from bottom to middle stories. Relative weighting factors are assigned as per the damage contribution. And the sequence for strengthening activities is proposed as per the computed weighting factors in descending order for regular RCC buildings. Therefore, proposals made in the study would increase the efficacy of strengthening activities.

• Geophysics and Geophysical Exploration
• /
• v.17 no.1
• /
• pp.28-33
• /
• 2014

We investigate the spatial distribution of highly conductive layer using the one-dimensional inversions of the new magnetotelluric (MT) measurements obtained at the mid-mountain (400 ~ 900 m in elevation) western area of Jeju Island and the previous MT data over Jeju Island, Korea. The conductive layer indicates the sedimentary layer comprised of Seoguipo Fomation and U Formation. There is a definite positive correlation between the top of conductive layer and the earth surface in elevation. On the contrary, the bottom of conductive layer has a negative correlation with the surface elevation. In other words, the conductive layer has a shape of convex lens, which is thickest in the central part. The basement beneath the conductive layer could be concave in the central part of Jeju Island. A kriging considering the correlation between the layer boundary and the surface elevation provides a reliable geoelectric structure model of Jeju Island. However, further studies, i.e. three-dimensional modeling and interpretation integrated with other geophysical or logging data, are required to reveal the possible presence of three-dimensional conductive body near the subsurface vent of Mt. Halla and the causes of the bias in the depths of layer estimated from MT and core log data.

• Journal of Technologic Dentistry
• /
• v.29 no.2
• /
• pp.197-211
• /
• 2007

With the development of orthodontics and increasing concerns on physical appearance, the number of patients has been steadily increasing. It is quite important not only to make effective cure plans and accurate diagnoses but also to have a thorough grasp of patients' malocclusion types and their occurrence frequency, in addition to patients' personality in order to cure the patients appropriately. This study is based on 946 malocclusion patients who had visited Chong-A Dental Hospital from 1999 to 2004 and investigated their aspects of malocclusion and characteristics of their gender, age and residence. The results are as follows. 1. The number of patients per year had been decreased until 2001, after which year the number had fluctuated. The number was the largest in 1999, 169 and the smallest in 2001, 140. Female occupied 68.0% of the total, twice as many as male, 32.0%) 2. Based on the Angle's classification, 19 or over year - old group was the largest of the total, 59.3% and 6 or younger year - old group, the smallest, 0.5%. The 19 or over year old group was less than a half of the total (47.4%) in 2003 and there were no patients who belonged to the 6 or younger year - old group in 2003 and 2004. 3. Distributions on the types of malocclusion have shown that 39.9 % of the total are in the Class I, the largest, 31.0% in the Class I and 29.2 in the Class II, the smallest. 1) The number of the ClassI was 73, the largest, that of the Class III being 35, the smallest in 1999. On the whole, the number of the Class I accounted for the largest part of the total. 2) The number of male patients in the Class II was the smallest, generally being the largest in the Class I. In case of female, that of the Class III was the smallest. 3) Based on the age, the Class I was the highest in between 7 and 13 age group, the Class III the lowest. The Class I occupied the largest around 40%. 4) In the shape of physiognomy, the meso occupied the largest part among all the Class, of which the Class II was the highest, 64.2%. The bracy was the largest in the Class I, and the dolicho in the Class III. 5) In the profile, the convex shape was the largest in the Class I and II, and especially in the Class II, over 3/4 of the total, 75.4%. In contrast, the direct shape was the largest in the Class III and the sunken shape occupied 33.3%, which was nearly ten times more than the case of the Class I and III. 6) In the asymmetry of physiognomy, the number of patients of the Class IIIwas the largest, 34.1% and that of the Class II, the smallest, 19.5%. It was found that about one fourth of the malocclusion patients were under the asymmetry of physiognomy. 4. In the distribution of patients' residence, 81.4% were from the Seoul Metropolis and 48.2% from Gangnam-Gu where Chong-A Dental Hospital is located and Seocho-Gu and Songpa-Gu which are adjacent to Gangnam-Gu.

• Journal of the Korean Geosynthetics Society
• /
• v.19 no.1
• /
• pp.83-91
• /
• 2020

In this study, the characteristics of support behavior according to the change of ground condition of the cast-in-place pile and the large Caisson foundation, which are increasingly used as foundations of large structures and bridges. the allowable bearing capacity calculated using the yield load analysis method was analyzed to calculate similar allowable bearing capacity for each method. In addition, the allowable bearing capacity calculated by the ultimate load analysis method was found to have a large difference in bearing capacity for each method. Through this point, it can be usefully used as an empirical formula for evaluating the settlement characteristics of piles in future design and construction. In addition, as a result of examining the ground force distribution during sedimentation of large caissons, the section of the weathered rock layer showed almost constant ground force distribution as ground forces decreased after yield occurred at the base corner. And in the bed rock layer section, the foundation's center was transformed into a ground force in the form of a convex downward due to an increase in the ground resistance of the central part. Using these results, the theory previously presented by Fang (1991) and Kőgler (1936) was proved.

• Progress in Medical Physics
• /
• v.27 no.2
• /
• pp.64-71
• /
• 2016

We develop a manufacture procedure for the production of a patient specific customized bolus (PSCB) using a 3D printer (3DP). The dosimetric accuracy of the 3D-PSCB is evaluated for electron beam therapy. In order to cover the required planning target volume (PTV), we select the proper electron beam energy and the field size through initial dose calculation using a treatment planning system. The PSCB is delineated based on the initial dose distribution. The dose calculation is repeated after applying the PSCB. We iteratively fine-tune the PSCB shape until the plan quality is sufficient to meet the required clinical criteria. Then the contour data of the PSCB is transferred to an in-house conversion software through the DICOMRT protocol. This contour data is converted into the 3DP data format, STereoLithography data format and then printed using a 3DP. Two virtual patients, having concave and convex shapes, were generated with a virtual PTV and an organ at risk (OAR). Then, two corresponding electron treatment plans with and without a PSCB were generated to evaluate the dosimetric effect of the PSCB. The dosimetric characteristics and dose volume histograms for the PTV and OAR are compared in both plans. Film dosimetry is performed to verify the dosimetric accuracy of the 3D-PSCB. The calculated planar dose distribution is compared to that measured using film dosimetry taken from the beam central axis. We compare the percent depth dose curve and gamma analysis (the dose difference is 3%, and the distance to agreement is 3 mm) results. No significant difference in the PTV dose is observed in the plan with the PSCB compared to that without the PSCB. The maximum, minimum, and mean doses of the OAR in the plan with the PSCB were significantly reduced by 9.7%, 36.6%, and 28.3%, respectively, compared to those in the plan without the PSCB. By applying the PSCB, the OAR volumes receiving 90% and 80% of the prescribed dose were reduced from $14.40cm^3$ to $0.1cm^3$ and from $42.6cm^3$ to $3.7cm^3$, respectively, in comparison to that without using the PSCB. The gamma pass rates of the concave and convex plans were 95% and 98%, respectively. A new procedure of the fabrication of a PSCB is developed using a 3DP. We confirm the usefulness and dosimetric accuracy of the 3D-PSCB for the clinical use. Thus, rapidly advancing 3DP technology is able to ease and expand clinical implementation of the PSCB.