• International Journal of Air-Conditioning and Refrigeration
• /
• 제9권1호
• /
• pp.29-38
• /
• 2001

In this paper, the defrosting characteristics of a PTC heating sheet is investigated by means of a defrosting heat source for the fin-tube heat exchanger in a refrigerator The defrosting characteristics of the PTC heating sheet are examined and compared with those of a conventional electric heater experimentally. It is found that the characteristics of the water draining rate with the defrosting time show a smoothly oscillating pattern when the PTC heating sheet Is used, and the drained water is completely melted. The defrosting efficiency of the PTC heating sheet is found to be about 75%, which is about 25% higher than that of the electric heater. Also, the reduction of the defrosting time and the increment of the defrosting efficiency may be obtained by improving the arrangement of the heating elements of the healing sheet. It is shown that the defrosting time of the PTC heating sheet increases linearly with the amount of frost, whereas the defrosting efficiency is nearly constant. When applying the PTC heating sheet to the refrigerating system, one should notice the fact that the defrosting performance of the PTC heating sheet may be degraded due to the repetitive operations.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.465-468
• /
• 2000

The procedure of semi-solid forming is composed of heating a billet, forming, compression holding and ejecting step. There are several methods to heat a billet during semi-solid forming process such as electric heating and induction heating. Usually in semi-solid forming process, induction heating has been adopted to achieve more uniform temperature of semi-solid material. Although induction heating is better method than any others, however, there is still difference of temperature between internal part and surface part of semi-solid material. Worse yet, in case of high liquid fraction of semi-solid material, liquid of the billet will flow down though solid of the billet still remains, which is very difficult to handle. In the present study, induction heating of semi-solid material with compulsive surface cooling has been performed to obtain uniform distribution of temperature. Distribution of temperature of the billets was measured and compared with that of conventional distribution of temperature. By this new induction heating method, not only temperature over the whole billet become uniform, but also control of temperature is possible.

• 대한기계학회논문집
• /
• 제16권8호
• /
• pp.1595-1602
• /
• 1992

An energy efficient drying system, utilizing a heat pump to recover the wasted heat with high efficiency is proposed. In conventional drying systems, over-heating occurs through a condenser as the same amount of air is provided into the evaportator and the condenser. In order to prevent the over-heating, part of the outlet air from the drying chamber must be bypassed to increase the rate of vaporization in the drying chamber without release of the heat from the system. Since a part of the heat in the condenser is used to heat the air during the drying process of the proposed system, a high drying efficiency and low SPC(Specific Power Consumption) could be obtained, Comparing the performances between the proposed heat pump and a conventional one, it was found that the drying efficiency of the proposed heat pump is higher than that of the conventional heat pump by an amount of 7-25%.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1570-1574
• /
• 2008

Various mechanical test were conducted on conventional and crosslinked ultra-high molecular weight polyethylene(UHMWPE) all prepared from the same lot of medical grade GUR 1050 for artificial joint. The conventional materials were not irradiated and treated by heating. The cosslinked materials were irradiated with $25kGy{\sim}200kGy$ by gamma-ray andthen annealed or remelted. Gamma-ray irradiation and heat treatment process were found to significantly impact the crystallinity, and hence the mechanical behavior, of the highly crosslinked UHMWPE. The radiation dose and heating conditions were key predictors of the uniaxial yielding, plastic flow, and failure properties of conventional and highly crosslinked UHMWPE. The correlation model from experiments would be the basic information to enhance the were resistance of artificial joint liner.

• 대한화학회지
• /
• 제53권5호
• /
• pp.553-559
• /
• 2009

Metal organic frameworks (MOF)과 유사하게 금속과 유기물로 이루어진 골격 물질 중 제올라이 트와 유사한 구조를 갖는 zeolitic imidazolate framework (ZIF)를 처음으로 마이크로파(MW)를 이용하여 합성하였다. ZIF 중 잘 알려진 ZIF-8을 전통적인 전기 가열(CE)과 마이크로파 조사로 합성하였으며 ZIF-8은 $140{\sim}180^{\circ}C}$의 범위에서 용이하게 얻을 수 있었다. MW 합성에 의해 ZIF-8을 신속 하게 합성할 수 있었으며 결정 크기는 전통적인 합성에 비해 전반적으로 감소하였다. $140{^{\circ}C}$에서의 합성 결과 전통 적인 합성에 비해 MW에 의해 약 5배의 반응 속도가 증가함을 알 수 있었고 4시간 이내에 합성 반응이 종료됨을 알 수 있었다. MW로 얻어진 ZIF-8은 CE에 의한 ZIF-8에 비해 증가된 표면적과 세공부피를 가 졌다. 얻어진 모든 ZIF-8은 질소 흡착 실험 결과 type-I 흡착 등온선을 보였고 미세 세공을 가짐을 알 수 있었다. FTIR 및 TGA 결과 두 방법으로 얻어진 ZIF-8은 서로 유사한 결합 및 열적 특성을 보였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.652-652
• /
• 2013

The conventional thermal chemical vapor deposition (CVD) setup for the graphene synthesis has mainly used convective heat transfer in order to heat a catalyst (e.g. Cu) up to $1,000^{\circ}C$. Although the conventional CVD has been so far widely accepted as the most appropriate candidate enabling mass-production of high-quality graphene, this method has stillremained under the standard for the commercialization largely due to the poor productivity arisen out of the required long processing time. Here, we introduced a fast and efficient synthetic route toward CVD-graphene. Unlike the conventional CVD using convection heat transfer, we adopted a CVD setup utilizing conduction heat transfer between Cu catalyst and rapid heating source. The high thermal conductive nature of Cu and the employed rapid heating source led to the remarkable reduction in processing timeas compared to the conventional convection based CVD (Fig. 1A), moreover, the synthesized graphene was turned out to have comparable quality to that synthesized by the conventional CVD (Fig. 1B). For the optimization of the conduction based CVD process, the parametric studies were thoroughly performed using through Raman spectroscopy and electrical sheet resistance measurement. Our approach is thought to be worth considerable in order to enhance productivity of the CVD graphene in the industry.

• 마이크로전자및패키징학회지
• /
• 제11권4호
• /
• pp.37-41
• /
• 2004

이동 통신 기기의 광대역화에 따라 기존의 인쇄 회로 기판에 비해 양호한 전기적 특성과 수동형 부품을 내장할 수 있는 LTCC(Low Temperature Co-fired Ceramic)에 대한 많은 연구 개발이 진행되고 있으나 불 균일한 수축으로 인해 적용에 한계를 보여 왔다. 본 연구에서는 짧은 시간내에 온도를 균일하게 올릴 수 있는 혼합 가열 방식을 개발하여 하부에서부터 시편의 얇은 층이 순차적으로 소결 되도록 하는 일 방향 소결의 조건을 제공하여 시편 상부 표면의 배선 형상이 종래의 전기로 가열보다 안정적으로 형성되는 결과를 얻었다. 기판의 소결 특성, 배선의 전기적 특성, 그리고 배선의 기계적 특성 등을 비교한 결과, 기판의 소형화와 배선의 고밀도화에 전기로 가열 보다 혼합 가열이 적용 가능성이 높음을 알 수 있었다.

• 한국산학기술학회논문지
• /
• 제5권3호
• /
• pp.218-222
• /
• 2004

본 연구에서는 분리형 이동코어 방식의 스탬퍼 금형을 개발하였고, 사출성형품 품질에 영향을 주는 인자 중에 이동코어 표면 가열 방식이 미세구조를 갖는 성형품 전사성에 미치는 영향에 대해 알아보았다. 이동코어 표면 가열방식은 이동코어를 가열하지 않는 일반사출방식, 할로겐램프를 이용한 복사형 가열방식과 기체화염을 이용해 가열하는 MmSH 방식을 사용했다. COC, PMMA 두 종류의 열가소성 수지를 사용하여 성형품을 제작한 결과, 이동코어 표면온도가 가장 높은 MmSH 방식에서 나노패턴 전사성이 가장 우수했고, 일반사출성형 방식으로 제작한 성형품에서 전사성이 가장 저조했다.

• 한국농공학회논문집
• /
• 제50권1호
• /
• pp.39-47
• /
• 2008

Most of the broiler houses in Korea have experienced problems on controlling the environmental conditions such as suitability, stability and uniformity of rearing condition inside the broiler house. It is very critical which if not properly controlled, would cause serious stress on the chickens. It is therefore urgent to develop optimum designs of naturally ventilated broiler house which is appropriate to the four seasons of Korea. Field experiment for this matter is very difficult to conduct due to the unpredictable and uncontrollable weather condition. In this study, the heating load of a naturally ventilated broiler house was calculated using TRANSYS 15 BES program while internal climate and thermal condition were computed using Fluent 6.2. The computed resulted of the conventional ventilation system (A) and upgraded ventilation system (B) (Seo et al, 2007) were compared with each other for cold season. The results of the Building Energy Simulation(BES) indicated that the system B, the upgraded ventilation system made 8% lower total heating load and 47% lower at only the broiler zone compared to the conventional broiler house. Considering the entire broiler house, the existence of middle ceiling made the heating energy 11% lower required than without middle ceiling. Accordingly, the system B with middle ceiling was found to save heating energy by 20% in average. This study showed that the BES program can be a very powerful to effectively compute the energy loads of agricultural building while the energy load is very close related to ventilation efficiency.

• 대한기계학회논문집B
• /
• 제31권8호
• /
• pp.694-701
• /
• 2007

The applications of a transcritical $CO_2$ cycle into water heaters show advantages over conventional systems in the respect of power consumption and heating efficiency because the $CO_2$ cycle has a high compressor discharge temperature. Besides, the heating performance of the transcritical $CO_2$ cycle can be improved by optimizing operating conditions. In this study, the heating performance of a variable speed $CO_2$ heat pump was measured and analyzed by varying refrigerant charge amount, EEV opening, compressor frequency and outdoor temperature. As a result, the optimum normalized charge for heating was 0.226. The COPs at the compressor frequencies of 40, 50 and 60 Hz were 2.94, 2.75 and 2.25, respectively. The heating performance of the $CO_2$ cycle with charge amount was more sensitive than the cooling performance. Moreover, the heating performance was improved significantly by optimizing of compressor frequency and EEV opening.