• Transactions of Materials Processing
• /
• v.32 no.4
• /
• pp.208-214
• /
• 2023

This paper discusses the deformation characteristics of a scaled-down automotive outer door panel with vacuum-assisted incremental sheet forming. The vacuum condition between the die and Al6052-H32 sheet with a thickness of 1.0 mm is reviewed with the goal of improving the geometrical accuracy of the target product. The material flow according to the forming tool path, including the multi-tool path and conventional contour tool path, is investigated considering the degradation of the pillow effect. To reduce friction between the tool and the sheet during incremental forming, automotive engine oil (5W-30) is used as a lubricant, and the strain field on the surface of the formed product is analyzed using ARGUS. By comparing the geometry and material flow characteristics of products under different test conditions, it is confirmed that the product surface quality can be significantly improved when the vacuum condition is employed in conjunction with a multi-tool path strategy.

• Transactions of Materials Processing
• /
• v.33 no.3
• /
• pp.161-168
• /
• 2024

Aluminum alloy sheets, compared to conventional steel sheets, face challenges in press forming due to their lower elongation. To enhance their formability, extensive research has focused on forming technologies at elevated temperatures, specifically warm forming at around 300℃ and hot forming at approximately 500℃. This study proposes that the formability of aluminum alloy sheets can be significantly enhanced using a multi-stage hot forming technique. The research also investigates whether the strength of the A6061 aluminum alloy, known for its precipitation hardening, can be maintained when formed below the precipitate solid solution temperature. In the experiments, the A6061-T6 sheet underwent heating and rapid cooling between 250 and 500℃. The mechanical properties were evaluated at each stage of the process. The findings revealed that when the initial heat treatment was below 350℃, the strength of the material remained unchanged. However, at temperatures above 400℃, there was a noticeable decrease in strength coupled with an increase in elongation. Conversely, when the secondary heat treatment was conducted at temperatures of 350℃ or lower, the strength remained comparable to that of the initial heat treated material. However, at higher temperatures, a reduction in strength and an increase in elongation were observed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.842-845
• /
• 2000

The purpose of this paper is to investigate the influences on mechanical properties of motor pistons manufactured by casting, conventional forging and powder forging, using the comparison of characteristics like microstructure, hardness, tensile strength, and elongation. To form conventional forging piston, the experiment of visioplasticity was performed. As the model material, plasticine was used. To form powder forging piston, the shape of piston was simplified as simple cup shape. Material properties like workability, density variation before and after forging, and strain loci of material during forging were investigated. Powder forging and conventional forging technologies were effective to gain dense microstructure. In powder forging, distribution of such dense microstructuer was uniform. For hardness, pistons from powder forging and conventional forging technologies were much better than that from casting. For tensile strength and elongation, powder forging and conventional forging technologies were also advantageous.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.234-237
• /
• 2008

It was reported that the semi-solid forming process has many advantages over the conventional forming process, such as a long die life, good mechanical properties and energy savings. It is very important, however, to control liquid segregation to gain mechanical property improvement of materials. During forming process, Rheology material has complex characteristics, thixotropic behavior. Also, difference of velocity between solid and liquid in the semi-solid state material makes a liquid segregation and specific stress variation. Therefore, it is difficult for a numerical simulation of the rheology Process to be Performed. General Plastic or fluid dynamic analysis is not suitable for the behavior of rheology material. The behavior and stress of solid particle in the rheology material during forging process is affected by viscosity, temperature and solid fraction. In this study, compression experiments of aluminum alloy were performed under each other tool shape. In addition, the dynamics behavior compare with Okano equation to Power law model which is viscosity equation.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.177-180
• /
• 2009

Tube hydroforming provides a number of advantages over the conventional stamping process, including fewer secondary operations, weight reduction, assembly simplification, adaptability to forming of complex structural components and improved structural strength and stiffness. A hydroformed vehicle body component has an attachment flange or the like-formed as an integral part of the hydroforming process. For a given flange shape, a parting plane for the dies is established relative to which the various surfaces of the flange shape, in cross section, have no significant reverse curvature. This study shows analysis results that form the flanged tubular parts in the hydroforming. The thickness variations and defects during the hydroforming for flange forming could be analyzed by FE analysis. FE analysis was performed by LS-DYNA/Dynaform 5.5.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.10a
• /
• pp.195-199
• /
• 2001

The flow turning process, an incremental forming process, is a cost-effective forming method for axi-symmetric intricate parts to net shape. However, the flow turning process shows a fairly complicated deformation, it is very difficult to obtain satisfactory results. Therefore extensive experimental and analytical research has not been carried out. In this study, an fundamental experiment was conducted to improve productivity with process parameters such as tool path, angle of roller holder($\alpha$), feed rate(v ) and comer radius of forming roller(Rr). These factors were selected as variables in the experiment because they were most likely expected to have an effect on spring back. The clearance was controlled in order to achieve the precision product which is comparable to deep drawing one. And also thickness and diameter distributions of a multistage cup obtained by flow turning process were observed and compared with those of a commercial product produced by conventional deep drawing.

• Transactions of Materials Processing
• /
• v.5 no.3
• /
• pp.239-255
• /
• 1996

A new forming technology has been developed to fabricate near-net shape products using light metal. A semi-solid forming technology has some advantages compared with the conventional forming processes such as die casting squeeze casting and hot/cold forging. In this study the numerical analysis of semi-solid filling for a straight die shape and orifice die shape in gate pattern is studied on semi-solid materials(SSM) of solid fraction fs =30% in A356 aluminum alloy. The finite difference program of Navier-Stokes equation coupled with heat transfer and solidification has been developed to predict a filling pattern and the temperature distribution of SSM. The programdeveloped in this study gives die filling patterns of SSM and final solidifica-tion region.

• Transactions of Materials Processing
• /
• v.17 no.7
• /
• pp.511-516
• /
• 2008

A drawbead die for the experimental determination of drawbead forces was newly introduced in this paper. While the conventional Nine's drawbead die inevitably includes effects of a blank holding force on the measured drawbead forces, the new drawbead die excludes it by removing the blank holder contact in the dieface. Therefore, the new drawbead die can provide more realistic drawbead forces without considering somewhat arbitrary effect of blank holder with the computational procedure of forming process. The drawbead opening force and restraining force obtained by adopting the two experimental dies were compared for the validation of accuracy in the FEM simulation of automotive fender forming process. The compared section strains and draw-ins confirmed that the present drawbead die provides better drawbead forces for an accurate FEM simulation of sheet metal forming process.

• Transactions of Materials Processing
• /
• v.17 no.7
• /
• pp.466-472
• /
• 2008

In this paper, tension tests and formability tests are performed to construct a database related to mechanical properties and the formability of the AZ31B Mg alloy sheet. A forming test with a hemi-spherical punch is conducted at varying temperatures to establish a forming limit diagram. In order to verify the applicability of the analysis using the conventional flow hardening model, a finite element analysis is performed on the hemi-spherical punch forming process and the results are compared with experimental ones. The study investigates problems involving a computational analysis that does not consider flow softening of the magnesium alloy at elevated temperatures.

• Transactions of Materials Processing
• /
• v.9 no.3
• /
• pp.274-283
• /
• 2000

A dynamic explicit finite element code for simulating sheet forming processes has been developed. The code utilizes the discrete Kirchhoff shell element and contact force is treated by a conventional penalty method. In order to reduce the computational cost, a new and robust contact searching algorithm has been developed and implemented into the code. In the method, a hierarchical structure of tool segments is built for each tool at the initial stage of the analysis. hierarchical structure is built in a way to divide a box to 8 sub-boxes, 2 in each direction, until the lowest level of the hierarchical structure contains exactly one segment of the tool or empty. Then at each time step, contact is checked from the box to sub-boxes hierarchically for each node. Comparisons of computational results of various examples with the existing ones show the validity of the method.