• Proceedings of the KIEE Conference
• /
• 2006.10c
• /
• pp.354-356
• /
• 2006

In this paper, the position control performance of networked control systems is analyzed when time delay through the network is considered. Integrating a control system into a network has great advantages over the traditional control system which uses point to point connection: it allows remarkable reduction in wiring, makes it easy to install and maintain the system, and improves compability. However, a networked control system has the critical defect that network uncertainties, such as time delay, can degrade the control system's performance. Therefore, the major concern of a networked control system is analyzing the effect of network uncertainties. This paper is concerned with PID controller performance for stability region, critical stability region and unstability region under the time delay in the Controller Area Network.

• International Journal of Automotive Technology
• /
• v.7 no.6
• /
• pp.687-695
• /
• 2006

This paper presents a network-based traction control system(TCS), where several electric control units(ECUs) are connected by a controller area network(CAN) communication system. The control system consists of four ECUs: the electric throttle controller, the transmission controller, the engine controller and the traction controller. In order to validate the traction control algorithm of the network-based TCS and evaluate its performance, a Hardware-In-the-Loop Simulation(HILS) environment was developed. Herein we propose a new concept of the HILS environment called the network-based HILS(Net-HILS) for the development and validation of network-based control systems which include smart sensors or actuators. In this study, we report that we have designed a network-based TCS, validated its algorithm and evaluated its performance using Net-HILS.

• Management & Information Systems Review
• /
• v.2
• /
• pp.335-354
• /
• 1998

In this study I construct CAN(Controller Area Network) for automobiles similar to LAN(Local Area Network) and build communication modules in the major part of an automobile to link several sub-systems. Since each station replaces the communication function of sub-systems and has various types of sensor, actuator, controller, and switch, every information about automobile's status is obtained from the network. The manufactured system showed a superior capability. The following is the contents of study. 1. The definition of communication packet through the analysis of CAN protocol. 2. The Design of modules using micro-controller 80C196CA. 3. The Network configuration.

• Proceedings of the KIEE Conference
• /
• 2002.07d
• /
• pp.2234-2236
• /
• 2002

In this paper, realized an automation system that applies the automobile electromotive mirror using CAN(Controller Area Network : ISO l1898). CAN is being used mainly in ECUs (Electronic Control Units) connection of control system or automobile inside. And it has high reliability in the various network protocol. To be realized position system, Automobile Electro mirror, has a strong point that estabilishment e decrease and ease of maintenance it compare PPP(Point-to-point) method of existed. The realization composed of three portions. One Input Slave Con which accept a user's input, another Output Slave Co which drove it makes the motor of electromotive mirr other Master Controller which interfacing the two Controller. Automobile electromotive mirror realized time system that will be able to minize the delay t point of time user's input until output point of time mirror.

• Journal of IKEEE
• /
• v.22 no.2
• /
• pp.518-521
• /
• 2018

IVN (in-vehicle network) connects various electronic modules in the vehicles. It requires real-time, low noise, high reliability, and high flexibility. It includes CAN (controller area network), CAN-FD (CAN flexible data rate), FlexRay, LIN (local interconnect network), SENT (single edge nibble transmission), and PSI5 (peripheral sensor interface 5). In this paper, their operation priciples, target applications, and pros and cons are explained.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.10
• /
• pp.40-46
• /
• 2009

Recently CAN (Controller Area Network) is widely used as an in-vehicle networking protocol for intelligent vehicle. The identifier field (ID) of CAN is used not only to differentiate the messages but also to give different priorities to access the bus. This paper presents a dynamic 10 allocation algorithm in order to enhance the real-time quality-of-service (QoS) performance. When the network traffic is increased, this algorithm can allocate a network resource to lower priority message without degradation of the real-time QoS performance of higher priority message. In order to demonstrate the algorithm's feasibility, message transmission delays have been measured with and without the algorithm on an experimental network test bed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.235-236
• /
• 2010

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.11
• /
• pp.5110-5116
• /
• 2011

In this paper, multiplexing automation system will be proposed for the automobile electromotive mirror using CAN(Controller Area Network) protocol which has been known that it has a high reliability on the signal in the various network protocols. To do this, a master controller and two (input/output) slave controllers (H/W) are being made and application layer (S/W) is being programmed for effective going and communicating between subsystems. The possibility of the effectiveness of application and control ability will be shown when the system has minimum electrical lines by testing the experimental systems which was made up of the automobile electromotive mirror.

• Proceedings of the KIEE Conference
• /
• 2004.05a
• /
• pp.80-82
• /
• 2004

Personal robot consist of various modules that have independent functions. Because personal robot has requirement that support various construction for user's tendency. Therefore, Middleware mechanism at support not only personal robot's main functional element but also embedded modules functional elements is required. Each module have various heterogeneous network interfaces and variable services and variables. Therefore, Middleware must support these various network interfaces. This paper, pointed in Controller Area Network(CAN) inreface that usually used in embedded system for control. For connect various heterogeneous network interfaces (Ethernet, RS232 etc..), it is necessary to modify bagic CAN frame format. And also make some kind of BUS topology for CAN network.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.2
• /
• pp.97-106
• /
• 1999

This paper proposes the structure and the algorithm of the Fuzzy-Neural Controller(FNNC) which is able to adapt itself to unknown plant and the change of circumstances at the Fuzzy Logic Controller(FLC) with the Neural Network. This Learning Fuzzy Logic Controller is made up of Fuzzy Logic controller in charge of a main role and Neural Network of an adaptation in variable circumstances. This construct optimal fuzzy controller applied to the 2-area load frequency control of power system, and then it would examine fitness about parameter variation of plant or variation of circumstances. And it proposes the optimal Scale factor method wsint three preformance functions( E, , U) of system dynamics of load frequency control with error back-propagation learning algorithm. Applying the controller to the model of load frequency control, it is shown that the FNNC method has better rapidity for load disturbance, reduces load frequency maximum deviation and tie line power flow deviation and minimizes reaching and settling time compared to the Optimal Fuzzy Logic Controller(OFLC) and the Optimal Control for optimzation of performance index in past control techniques.