• 한국소음진동공학회논문집
• /
• 제25권8호
• /
• pp.553-558
• /
• 2015

This paper aims at making a dedicated vibration monitoring and diagnosis framework for 3MW WTG(wind turbine generator). Within the scope of the research, vibration data of WTG drive train are used and WTG operating conditions are involved for dividing the vibration data class which included transient and steady state vibration signals. We separate two health detections which are CHD(continuous health detection) and EHD(event health detection). CHD has function of early detection and continuous monitoring. EHD makes the use of finding vibration values of fault components effectively by spectrum matrix subsystem. We proposed framework and showed application for 3MW WTG in a practical point of view.

• 대한기계학회논문집A
• /
• 제24권10호
• /
• pp.2413-2419
• /
• 2000

Harmonic resonances in a continuous rotating shaft with distributed mass are discussed. The restoring force of the shaft has geometric stiffening nonlinearity due to the extension of the shaft centerline. The effect of a distributed lateral force, such as the gravity, is assumed. The possibility of the occurrences of harmonic resonances, the shapes of resonance curves, and internal resonance phenomena are investigated.

• 한국공작기계학회논문집
• /
• 제10권1호
• /
• pp.43-50
• /
• 2001

Subharmonic resonances of order 1/2 of a continuous rotating shaft with distributed mass are discussed. The restoring force of the shaft exhibits geometric stiffening nonlinearity due to the extension of the shaft center line. It is assumed that a distributed lateral force, such as the gravity, acts on the rotor. The possibility of the occurrence of subharmonic resonances, the shapes of resonance curves, and internal resonance phenomena are investigate.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 추계학술발표대회 논문집
• /
• pp.220-223
• /
• 2000

A method of calculating the natural frequency corresponding to the modes of vibration of beams and tower structures, with irregular cross sections and with arbitrary boundary conditions was developed and reported by Kim, D. H. in 1974. In this paper, the result of application of this method to the three span continuous reinforced concrete bridge with elastic intermediate supports is presented. Such bridge represents either concrete or sandwich type three span bridge on polymeric supports for passive control or on actuators for active control The concrete slab is considered as a special orthotropic plate. The influence of the modulus of the foundation and $D_{22}$, $D_{12}$, $D_{66}$ stiffnesses on the natural frequency is thoroughly studied.

• Advances in Computational Design
• /
• 제1권2호
• /
• pp.155-173
• /
• 2016

This paper presents a method of design for the energy harvesting of a piezoelectric cantilever beam. Vibration modes have strain nodes where the strain distribution changes in the direction of the beam length. Covering the strain nodes of the vibration modes with continuous electrodes effects a cancellation of the voltages outputs. The use of segmented electrodes avoids cancellations of the voltage for multi-mode vibration. The resistive load affects the voltage and generated power. The optimum resistive load is considered for segmented and continuous electrodes, and then the power output is verified. One of the effective parameters on energy harvesting performance is the existence of concentrated mass. This topic is studied in this paper. Resonance and off-resonance cases are considered for the harvester. In this paper, both theoretical and experimental methods are used for satisfactory results.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.34-35
• /
• 2014

we designed a distributed mass dynamic vibration absorber for vibration reduction in a dual mode system. And we were subjected to evaluation of the vibration reduction performance of the distributed mass dynamic vibration absorber through experiments.

• Geomechanics and Engineering
• /
• 제13권2호
• /
• pp.269-284
• /
• 2017

A new technique is proposed to obtain more effective screening efficiency against the ground vibration using intermittent geofoam (IF) in-filled trench. The numerical analysis is performed by employing two-dimensional finite element method under dynamic condition. Vertically oscillated strip foundation is considered as the vibration source. In presence of the ground vibration, the vertical displacements at different locations (pick-up points) along the ground surface are captured to determine the amplitude reduction factor (ARF), which helps to assess the efficiency of the vibration screening technique. The efficiency of IF over continuous geofoam (CF) in-filled vibration barriers is assessed by varying the geofoam density, the location of trench and the frequency of excitation. The results from this study indicate that a significant reduction in ARF can be achieved by using intermittent geofoam as compared to continuous geofoam. Further, it is noticed that the efficiency of IF increases with an increase in the frequency of the vibrating source. These encouraging results put forward the potential of utilising intermittent geofoam as a vibration screening material.

• Steel and Composite Structures
• /
• 제21권1호
• /
• pp.195-216
• /
• 2016

The dynamic characteristics of continuous steel-concrete composite beams considering the effect of interlayer slip were investigated based on Euler Bernoulli's beam theory. A simplified calculation model was presented, in which the Mode Stiffness Matrix (MSM) was developed. The natural frequencies and modes of partial-interaction composite continuous beams can be calculated accurately and easily by the use of MSM. Proceeding from the present method, the natural frequencies of two-span steel-concrete composite continuous beams with different span-ratios (0.53, 0.73, 0.85, 1) and different shear connection stiffnesses on the interface are calculated. The influence pattern of interfacial stiffness on bending vibration frequency was found. With the decrease of shear connection stiffness on the interface, the flexural vibration frequencies decrease obviously. And the influence on low order modes is more obvious while the reduction degree of high order is more sizeable. The real natural frequencies of partial-interaction continuous beams commonly used could have a 20% to 40% reduction compared with the fully-interaction ones. Furthermore, the reduction-ratios of natural frequencies for different span-ratios two-span composite beams with uniform shear connection stiffnesses are totally the same. The span-ratio mainly impacts on the mode shape. Four kinds of shear connection stiffnesses of steel-concrete composite continuous beams are calculated and compared with the experimental data and the FEM results. The calculated results using the proposed method agree well with the experimental and FEM ones on the low order modes which mainly determine the vibration properties.

• 대한기계학회논문집A
• /
• 제27권5호
• /
• pp.734-741
• /
• 2003

This paper addresses the vibration mode shape Measurement technique utilizing a Continuous Scanning Laser Doppler Vibrometer (CSLDV). The continuous scanning capability is added to the conventional discrete Laser Doppler Vibrometer by reflecting the laser beams on the surface of the object using two oscillating mirrors. The bow scanning resulted from the proposed scanning method is eliminated by feedback control. The velocity output signal from the CSLDV is modulated to give the spatial velocity distribution in terms of coefficients which are obtained from the Fast Fourier Transformation of the time dependent velocity signal. Using the Chebyshev series from, the analysis of the vibration mode shape techniques for straight line scanning and 2 dimensional scanning are presented and discussed. The performance of the proposed SLDV is presented using the experimental results of the vibration mode shape of a cantilever and plate

• 조명전기설비학회논문지
• /
• 제18권1호
• /
• pp.122-128
• /
• 2004

본 논문에서는 가동자의 이동방향에 따른 진동과 고정자에 대하여 수직으로 작용하는 진동을 동시에 고려할 수 있는 이론을 제시함에 있어서, LSM의 구조를 기초로 자기등가회로를 구성하였으며, 자기등가회로에 대한 방정식을 이용하여 LSM의 전기적인 등가회로를 유도하였다. 그리고, LSM의 변위에 따른 수직력 분포를 유한요소법(Flux2D)으로 계산하였으며 이를 방정식으로 나타내었다. 최종적으로 1상 여자방식에 의한 가동자의 이동방향에 따른 진동과 고정자에 대하여 수직으로 작용하는 진동을 전압방정식, 추력 및 수직력 방정식, 운동방정식을 사용하여 ACSL(Advanced Continuous Simulation Language)에 의하여 시뮬레이션 하였다.