• Proceedings of the KIPE Conference
• /
• 1996.06a
• /
• pp.5-12
• /
• 1996

In this paper, we design a Continuous Variable Structure Controller which can control robot manipulators to follow the desired planned trajectory with accuracy and robustness, and improve continuity and robustness of variable structure control, based on disturbance observer. We also analyze the stability the proposed algorithm and then verify the usefulness and performance through simulation stuies.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1126-1131
• /
• 2007

This paper presents unified chassis control (UCC) to improve the vehicle lateral stability. The unified chassis control implies combined control of active front steering (AFS), electronic stability control (ESC) and continuous damping control (CDC). A direct yaw moment controller based on a 2-D bicycle model is designed by using sliding mode control law. A direct roll moment controller based on a 2-D roll model is designed. The computed direct yaw moment and the direct roll moment are generated by AFS, ESP and CDC control modules respectively. A control authority of the AFS and the ESC is determined by tire slip angle. Computer simulation is conducted to evaluate the proposed integrated chassis controller by using the Matlab, simulink and the validated vehicle simulator. From the simulation results, it is shown that the proposed unified chassis control can provide with improved performance over the modular chassis control.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.1
• /
• pp.117-129
• /
• 1998

Micro-hole drilling (holes less than 0.5 mm in diameter with aspect ratio larger than 10) is recently having more attention in a wide spectrum of precision production industries. Alternative methods such as EDM. laser drilling, etc. can sometimes replace the mechanical micro-hole drilling but are not acceptable in PCB manufacture because of the inferior hole quality and accuracy. The major difficulties in micro-hole drilling are related to small signal to noise ratios, wandering motions of the inlet stage, high aspect ratios, high temperatures and so forth. Of all the difficulties. the most undesirable one is the increase of drilling force as the drill proceeds deeper into the hole. This is caused mainly from the chip effects. Peck-drilling is thus widely used for deep hole drilling despite that it suffers from low productivity. In the paper, a method of cutting force regulation is proposed to achieve continuous drilling. A PD and a sliding mode control algorithms were implemented through controlling the spindle rotating frequency. Experimental results show that the sliding mode control reduces the nominal cutting force and the variation of the cutting force better than the PD control. The advantages of the regulation, such as increase of drill life, fast stabilization of a wandering motion, and the precise positioning of the hole are verified in experiment.

• Journal of Electrical Engineering and information Science
• /
• v.3 no.1
• /
• pp.58-66
• /
• 1998

A continuous, accurate, and robust variable structure tracking controller(CVSTC) is designed for brushless direct drive servo motors(BLDDSM). Although conventional variable structure controls can give the desired tracking performances, there exists an inevitable chattering problems in control input which is undesirable for direct drive systems. With the presented algorithm, not only the chattering problems are removed by using the efficient compensation of the disturbance observer, but also the prescribed tracking trajectory can be obtained using the sliding dynamics when an initial of the desired trajcetory is different from that of a BLDDSM. The design of the sliding mode tracking controller for the prescribed, accurate, and robust tracking performance without the chattering problem is given based on the results of the detailed stability analysis. The usefulness of the suggested algorithm is demonstrated through the computer simulation for a BLDDSM under load variations.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.1
• /
• pp.60-66
• /
• 1996

Brushless DC(BLDC) motor have been increasingly used in machine tools and robotics applications due to the reliability and the efficiency. In control of BLDC motor, it is important to construct the controller which is robust to parameter variations and external disturbances. Variable structure controller(VSC) has been known as a powerful tool in robust control of time varying systems. In practical systems, however, VSC has a high frequency chattering which deteriorates system performances. In this paper, a binary controller(BC) which takes the form of VSC and MRAC combined is presented to solve this problem. BC consists of the primary loop controller and the external loop controller to change the gain of primary loop controller smoothly. So it can generate the continuous control input and is insensitive to parameter variations in the given domain. To confirm the validity, various investigations of control characteristics for various design parameters in a position control system of BLDC motor are carried out. (author). 11 refs., 18 figs., 1 tab.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.3
• /
• pp.262-268
• /
• 1988

In this paper conditions are derived, which ensure the existence of a quasi-sliding mode on the control switching hyperplane in discrete variable structure control systems and also remove the reaching phase problem observed in continuous-time variable structure systems. In addition, a discrete variable structure tracking controller which has adaptive properties is devised based on these results. This controller has useful properties, such as small sensitivity to the variation of plant parameters and to disturbances and its performing speed is fast compared to that of other adaptive controller.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.5
• /
• pp.1886-1900
• /
• 2018

This paper proposes a confronting feedback control structure and controllers for positive output elementary super lift Luo converters (POESLLCs) working in discontinuous conduction mode (DCM). The POESLLC offers the merits like high voltage transfer gain, good efficiency, and minimized coil current and capacitor voltage ripples. The POESLLC working in DCM holds the value of not having right half pole zero (RHPZ) in their control to output transfer function unlike continuous conduction mode (CCM). Also the DCM bestows superlative dynamic response, eliminates the reverse recovery troubles of diode and retains the stability. The proposed control structure involves two controllers respectively to control the voltage (outer) loop and the current (inner) loop to confront the time-varying ON/OFF characteristics of variable structured systems (VSSs) like POESLLC. This study involves two different combination of feedback controllers viz. the proportional integral controller (PIC) plus sliding mode controller (SMC) and the fuzzy logic controller (FLC) plus SMC. The state space averaging modeling of POESLLC in DCM is reviewed first, then design of PIC, FLC and SMC are detailed. The performance of developed controller combinations is studied at different working states of the POESLLC system by MATLAB-Simulink implementation. Further the experimental corroboration is done through implementation of the developed controllers in PIC 16F877A processor. The prototype uses IRF250 MOSFET, IR2110 driver and UF5408 diodes. The results reassured the proficiency of designed FLC plus SMC combination over its counterpart PIC plus SMC.

• Journal of IKEEE
• /
• v.8 no.1 s.14
• /
• pp.96-107
• /
• 2004

In this paper, a new integral variable structure regulation controller(IVSRC) is designed by using a special integral sliding surface and a disturbance observer for the improved regulation control of highly nonlinear robot manipulators with prescribed output performance. The sliding surface having the integral state with a special initial condition is employed in this paper to exactly predetermine the ideal sliding trajectory from a given initial condition to origin without any reaching phase. And a continuous sliding mode input using the disturbance observer is also introduced in oder to effectively follow the predetermined sliding trajectory within the prescribed accuracy without large computation burden. The performance of the prescribed tracking accuracy to the predetermined sliding trajectory is clearly investigated in detail through the two theorems together with the closed loop stability. The design of the proposed IVSRC is separated into the performance design and robustness design in each independent link. The usefulness of the algorithm has been demonstrated through simulation studies on the regulation control of a two link manipulator under parameter uncertainties and payload variations, in view of no reaching phase, no overshoot, predetermined response with prescribed accuracy, easy change of output performance, separation of design phase, and so on.

• Proceedings of the KIEE Conference
• /
• 2008.04a
• /
• pp.205-206
• /
• 2008

고전석인 슬라이딩 모드 제어는 시스템의 동특성에 관계없이 시스템의 상태를 설계자의 의도대로 목적에 맞게 제어할 수 있지만 시스템의 본질적인 한계로 인해 제어입력에서 채터링이라는 불가피한 요소를 포함하게 된다. 본 논문에서는 이산 시간 시스템에서 고주파 성분으로 인한 스위칭 입력의 부정적인 영향인 채터링을 감소시키기 위해 연속 슬라이딩 모드 제어기법을 제안한다. 제안된 기법은 PZT 나노 스테이지에서 슬라이딩 모드의 강인성과 만족스러운 시스템 제어성능을 보여준다.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.14-19
• /
• 1993

In this paper, we proposed an indirect learning and direct adaptive control schemes using neural networks, i.e., composite adaptive neural control, for a class of continuous nonlinear systems. With the indirect learning method, the neural network learns the nonlinear basis of the system inverse dynamics by a modified backpropagation learning rule. The basis spans the local vector space of inverse dynamics with the direct adaptation method when the indirect learning result is within a prescribed error tolerance, as such this method is closely related to the adaptive control methods. Also hash addressing technique, similar to the CMAC functional architecture, is introduced for partitioning network hidden nodes according to the system states, so global neuro control properties can be organized by the local ones. For uniform stability, the sliding mode control is introduced when the neural network has not sufficiently learned the system dynamics. With proper assumptions on the controlled system, global stability and tracking error convergence proof can be given. The performance of the proposed control scheme is demonstrated with the simulation results of a nonlinear system.