• 한국생산제조학회지
• /
• 제7권4호
• /
• pp.50-55
• /
• 1998

Mould level control system for continuous casting process involves stick-slip friction in the sliding gate , time-delay, non-linearity, and certain uncertainties such as friction force variations between molten steel and the inner wall of mould. In this paper, sliding mode control technique was used to solve these complex control problem. The controller is then designed and implemented onto the continuous casting process. Testing result shows that sliding mode controller can decrease the fluctuating magnitude of the mould level and is superior to the existing PID controller.

• 한국생산제조학회지
• /
• 제7권2호
• /
• pp.9-14
• /
• 1998

One of the areas in the continuous casting process that up to this point, has not been definitively instrumented is a method of reliably locating the part of a continuously cast strand that remains liquid for a period after the outer portion has solidified. To solve the problem. Electromagnetic Trandsducers(EMAT) which operate across an air gap without the need for a coupling medium has been developed. The system was designed to employ a through transmission technique which enhanced the signal-to-noise ratio. The Al 75$\times$75mm and 75$\times$100mm simulators with 2, 4, 8, 16, 32 mm hole respectively has been produced in order to verify the developed EMAT system and to measure to liquid core in continuous casting strand. The system developed can be employed for the optimization of torch cutting speed and for the final cut length of the bloom as well as calculation of average bloom temperature.

• 한국CDE학회논문집
• /
• 제19권2호
• /
• pp.148-156
• /
• 2014

Generally, over 95% of manufacturing cost is determined in the design and manufacturing preparation step, especially a great part of productivity is determined in the manufacturing preparation step. In order to improve the manufacturing competitiveness, we have to verify the problems that can be occurred in the production step and remove the unnecessary factors in the manufacturing preparation step. Thus, manufacturing industries are adopting digital manufacturing system based on modeling & simulation. In this paper, we introduce e-FEED system (electronic based Front End Engineering and Design) that is the integrated design and analysis system for optimized manufacturing line development based on simulation automation and explain the work process (Design, Analysis and Optimization) about manufacturing line development using e-FEED system. Also, the effect is described through the real implementation cases.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 하계종합학술대회 논문집(5)
• /
• pp.211-214
• /
• 2002

Under a continuous manufacturing process, two dimension inspection system causes problems as blurring effect and low resolution and requires position calibration between frames. One dimension inspection system is, therefore, being researched as a substitution. In this paper, we implement mechanism of switching memory and processing data for reasonable one dimension inspection system. Redundant weft image and noise was suggested to be reduced by new method using modified morphological process and masked erosion process. From resulting image, line data and possible error information were obtained and constructed as a structure. Finally, error detecting algorithm was performed with this data structure. Processing time of error detecting was 0.625ms per line in applied system and experiment showed 94.7% of error detecting ability. This method is 20% faster in speed and 2.7% higher in error detecting ability comparing with the present method.

• 한국생산제조학회지
• /
• 제25권3호
• /
• pp.217-223
• /
• 2016

In this research, a continuous roll-to-roll screen printing system was developed using a flat screen. It has a newly devised sliding mechanism of screen printing module, which can be controlled accurately in sync with a moving web, driven by a roll-to-roll tension control and web-guiding system. In addition, the real-time precision alignment module that consists of a vision camera and an $X-Y-{\theta}$ alignment stage was implemented. With this developed system, the feasibility of continuous printing with minimum pattern width below $60{\mu}m$ was verified, and an overlay of ${\pm}60{\mu}m$ between the laser-patterned reference mark and the printed mark on a 300-mm-wide film was achieved.

• 한국정밀공학회지
• /
• 제32권8호
• /
• pp.673-680
• /
• 2015

A roll-to-roll (R2R) continuous manufacturing system for a carbon-nanotube (CNT)-/silver-nanowire (AgNW)- based large-area transparent conductive film was introduced in this study. The systemic guidelines of the R2R slot-die coating process including roll eccentricity, wrap angle, pump accuracy, and blower influence were discussed. To simulate the coating phenomenon, we investigated the governing parameters of the coating process by incorporating the estimated relative thickness that was defined by combining the viscocapillary model and volume model. By using experimental and mathematical approaches, an excellent transparent conductive layer with a $40{\Omega}/{\Box}$ sheet resistance and 88 % transmittance was obtained; moreover, a dimensionless number identifies the correlation between the transparent conductive film and the anti-reflection film.

• International Journal of Precision Engineering and Manufacturing
• /
• 제9권3호
• /
• pp.7-12
• /
• 2008

Today, manufacturers are forced to acknowledge that the life cycles of products are becoming shorter. In the case of the door trim assembly field, the highly frequent introduction of new products and the continuous increase in product varieties leads to the demand for redesigning assembly systems more often. Modular manufacturing systems can be an important issue in helping to overcome these problems. This paper presents the development of a modular assembly system for the door trim, and because it takes the change drives into consideration, this system is highly flexible in adapting to changes in the environment.

• 한국기계가공학회지
• /
• 제12권4호
• /
• pp.22-28
• /
• 2013

It is important to begin left ventricular assist device (LVAD) treatment at appropriate time for heart failure patients who expect cardiac recovery after the therapy. In order to predict the optimal timing of LVAD implantation, we predicted pumping efficacy of LVAD according to the severity of heart failure theoretically. We used LVAD-implanted cardiovascular system model which consist of 8 Windkessel compartments for the simulation study. The time-varying compliance theory was used to simulate ventricular pumping function in the model. The ventricular systolic dysfunction was implemented by increasing the end-systolic ventricular compliance. Using the mathematical model, we predicted cardiac responses such as left ventricular peak pressure, cardiac output, ejection fraction, and stroke work according to the severity of ventricular systolic dysfunction under the treatments of continuous and pulsatile LVAD. Left ventricular peak pressure, which indicates the ventricular loading condition, decreased maximally at the 1st level heart-failure under pulsatile LVAD therapy and 2nd level heart-failure under continuous LVAD therapy. We conclude that optimal timing for pulsatile LVAD treatment is 1st level heart-failure and for continuous LVAD treatment is 2nd level heart-failure when considering LVAD treatment as "bridge to recovery".

• 한국기계가공학회지
• /
• 제11권6호
• /
• pp.152-157
• /
• 2012

This study investigates compressive strength of ice pellet strip which is potential medium for Natural Gas Hydrate(NGH) extruded from die holes of Twin-roll Press for Continuous Pelletizing(TPCP). Recently, the prototype of TPCP is newly developed where ice powder is continuously fed and extruded into strip-type pellet between twin rolls. The system is specifically designed for future expansion towards mass-production of ice pellet strips or solid form of natural gas hydrate. It is shown that the compressive strength of pellet strip heavily depends on factors in extrusion process such as disk size, surface smoothness, ring size, taper shape, feeding mechanism, and rotational speed. Here, the mechanism of TPCP, along with compressive strength of pellets is discussed in terms of its feasibility for producing NGH pellets in the future.

• 한국산업정보학회논문지
• /
• 제14권4호
• /
• pp.75-90
• /
• 2009

생산성 향상과 효율적인 프로세스 관리는 기존 업무의 문제점을 올바르게 파악하는 것에서부터 시작한다. 또한 데이터 수집에서 필요한 정보를 도출하는 데 많은 시간이 소요될 경우 고객의 요구와 수요를 충족시키고 업무의 효율성을 높이기 위한 지속적인 프로세스 관리가 더욱 어려워진다. 본 논문은 실시간 정보획득 기술의 도입을 통해 제조공정 관리상 발생 가능한 여러 문제점을 개선하기 위한 방안과 기초적 의사결정을 위한 상황인지(Context awareness) 시스템을 제시하는 것을 목적으로 한다. 공정 작업 중 획득한 데이터를 바탕으로 각 작업을 자동으로 분류하는 판단규칙을 제시하여 제조 현장에서의 상황인지를 구현하고자 하였다. 그리고 제안하는 개념과 구조를 작업자가 신속하게 문제를 파악하고 지시사항을 전달할 수 있는 사례를 기본적 시스템으로 구현하였다. 생산요소 객체 및 정보시스템의 데이터 일치와 공정에 대하 지속적이 모니터링을 통해 비효율적 자원 할당 및 공정 지연을 측정하고 해결하며 가시성을 높여 업무 효율을 지속적으로 향상시킬 수 있을 것이다.