• 대한기계학회논문집A
• /
• 제32권12호
• /
• pp.1107-1114
• /
• 2008

This paper is aimed to understand the effect of different galvannealing temperatures on the frictional properties and Fe-Zn intermetallic phases of the galvannealed (GA) coatings on steel sheets. Their galvannealing treatments were conducted at 465, 505, 515 and $540^{\circ}C$ for about 10s in the additional heating furnace of an industrial continuous hot-dip galvanizing line. The mechanical and the frictional properties of the coatings were estimated using nanoindentation, nanoscratch, micro vickers hardness tests and flat friction tests, which were performed at contact pressures of 4, 20 and 80MPa. Also, the correlation between the microstructure and the frictional properties of the GA coatings were investigated by SEM observation for the cross-section of the GA coating after and before flat friction tests. The results showed that the mechanical and the frictional properties of the coatings are strongly dependent on their phase distributions and microstructure. Especially, in low contact pressure of 4MPa the frictional properties of the coatings were dependent on the surface phases and morphology, while in high contact pressure of 80MPa it was influenced by their mechanical properties based on the dominant phase distributions.

• 한국염색가공학회지
• /
• 제16권5호
• /
• pp.28-34
• /
• 2004

The polarizing film application exploits the unique physicochemical properties between PVA(Poly vinyl alcohol) film and CTA(Cellulose triacetate) film. However, hardly any research was aimed at improving the adhesion characteristics of the CTA film by radio frequency(RF) plasma treatment at argon(Ar) gaseous state. In this report, we deal with surface treatment technology for protective CTA film developed specifically for high adhesion applications. After Ar plasma, surface of the films is analyzed by atomic force microscopy(AFM), roughness parameter and peel strength. Furthermore, the wetting properties of the CTA film were studied by contact angle analysis. Results obtained for CTA films treated with a glow discharge showed that this technique is sensitive to newly created physical functions. The roughness and peel strength value increased with an increase in treatment time for initial treatment, but showed decreasing trend for continuous treatment time. The result of contact angle measurement refer that the hydrophilicity of surface was increased. AFM studies indicated that no considerable change of surface morphology occurred up to 3 minutes of treatment time, but a considerable uneven of surface structure resulted from treating time after 5 minutes.

• 지식경영연구
• /
• 제20권3호
• /
• pp.17-38
• /
• 2019

Rrecently, companies have made great efforts to satisfy various needs and heightened expectations of customers, and the importance of customer center as customer contact department for customer relationship management is increasing. In the knowledge ecosystem, corporate customer centers are emerging as a new alternative to acquiring corporate competitiveness by increasing sales and increasing market share by improving marketing support activities and customer relationship management at customer contact points. As a result, the interest in the customer center has increased rapidly because it provides the opportunity to contact with the customer. In addition, in the era of the fourth industrial revolution, the customer center, which is a collection of information and communication technologies, has a big databased voice recognition technology to elaborate customer service, thereby enhancing customer satisfaction and contributing to marketing through continuous interaction with customers. Of course, we have the opportunity to transform into the frontline business intelligence front for customer knowledge. This study is a comparative case study on how the customer center of K Life Insurance that takes the lead in the customer center industry has successfully renewed and established their key information systems to improve customer services and reinforce marketing support competencies. Based on the above, this study will present factors affecting successful implementation and settlement of the customer service information systems of customer centers by independently analyzing two individual cases.

• 대한임베디드공학회논문지
• /
• 제18권6호
• /
• pp.277-283
• /
• 2023

Vital signals provide essential information regarding the health status of individuals, thereby contributing to health management and medical research. Present monitoring methods, such as ECGs (Electrocardiograms) and smartwatches, demand proximity and fixed postures, which limit their applicability. To address this, Non-contact vital signal measurement methods, such as CW (Continuous-Wave) radar, have emerged as a solution. However, unwanted signal components and a stepwise processing approach lead to errors and limitations in heart rate detection. To overcome these issues, this study introduces an integrated neural network approach that combines noise removal, demodulation, and dominant-frequency detection into a unified process. The neural network employed for signal processing in this research adopts a MLP (Multi-Layer Perceptron) architecture, which analyzes the in-phase and quadrature signals collected within a specified time window, using two distinct input layers. The training of the neural network utilizes CW radar signals and reference heart rates obtained from the ECG. In the experimental evaluation, networks trained on different datasets were compared, and their performance was assessed based on loss and frequency accuracy. The proposed methodology exhibits substantial potential for achieving precise vital signals through non-contact measurements, effectively mitigating the limitations of existing methodologies.

• Current Photovoltaic Research
• /
• 제2권4호
• /
• pp.173-176
• /
• 2014

We have investigated the seed layer formation of front side contact using the inkjet printing process. Conductive silver ink was printed on textured Si wafers with 80 nm thick $SiN_x$ anti reflection coating (ARC) layers and thickened by light induced plating (LIP). The inkjet printable sliver inks were specifically formulated for inkjet printing on these substrates. Also, a novel method to prepare nano-sized glass frits by the sol-gel process with particle sizes around 5 nm is presented. Furthermore, dispersion stability of the formulated ink was measured using a Turbiscan. By implementing these glass frits, it was found that a continuous and uniform seed layer with a line width of $40{\mu}m$ could be formed by a inkjet printing process. We also investigated the contact resistance between the front contact and emitter using the transfer length model (TLM). On an emitter with the sheet resistance of $60{\Omega}/sq$, a specific contact resistance (${\rho}_c$) below $10m{\Omega}{\cdot}cm^2$ could be achieved at a peak firing temperature around $700^{\circ}C$. In addition, the correlation between the contact resistance and interface microstructures were studied using scanning electron microscopy (SEM). We found that the added glass particles act as a very effective fire through agent, and Ag crystallites are formed along the interface glass layer.

• 열처리공학회지
• /
• 제15권1호
• /
• pp.16-20
• /
• 2002

In conventional metallothermic reduction(MR) for obtaining tantalum powder in batch-type operation, it is difficult to control morphology and location of deposits because the reaction occurs by direct physical contact between reductants and feed materials. On the other hand, a electronically mediated reaction(EMR) is capable to overcome these difficulties through the reaction by electron transfer and have a merit of continuous process. In this study an MR and EMR method has been applied to the production of a tantalum powder by sodium reduction of $K_2TaF_7$. As the reduction temperature increases, the particle size and yield of tantalum powder obtained by MR and EMR method is increased.

• 한국정밀공학회지
• /
• 제22권1호
• /
• pp.103-108
• /
• 2005

In this study, to develop a flash-less mold for forming of shoe-outsole, experiments and forming analysis were carried out. In order to reduce the extra-materials, offset method and mass distribution method are used in the preform design. The vertical mold structure pressing the preform was introduced to produce a flash-less shoe-sole. To measure the contact status of parting surface of mold, the pressure film has been used. The guide-gutter system and the continuous pressing mold have been developed for the discharge of extra-materials and re-pressing. By the investigation, flash of shoe-outsole was considerably reduced.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1996년도 가을 학술발표회 논문집
• /
• pp.210-217
• /
• 1996

Under strong shock loads including earthquake or blast, structures may start to crack in stress concentrated members. The continuous behavior of the structure changes to the discontinuous. In this study, numerical method analyzing continuous and discontinuous behavior of a structure is developed using a modified distinct element method. Equations of motion of each distinct element are integrated using the central difference method, one of the finite difference methods. Interactions between he elements are considered by an element and pore spring. The forces acting in the center of an element include contact stress transferred by element spring; tensile stress by pore spring; and external traction such as earthquake or blast load. To verify the proposed method, the behavior of the cantilever beam subject to the quasi-static concentrated force at the end is investigated. The failure behavior of the simply supported beam subject to the strong shock at the center is studied. The proposed method can predict the failure behavior of the structure due to the shock loading and the post-failure discontinuous behavior of the structure.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.655-659
• /
• 2001

Resident time of the continuous and Instantaneous centrifugal separator using that separates the light and heavy liquids by use of density difference is the orptical factor that affects significantly the chemical metial extraction and the productivity in the chemical and mechanical process. In this paper, the overflow of the device is investigated under consideration of the relationships between inclination angle of liquid feeding screw and the centrifugal force. From the design of the length of a centrifugal separator, the radiuses of rotor and housing, theoretical formulation on the contact radius of separation weir is established through the experiments. From the experiments, it is identified that how much the capacity of inlet impeller and the emulsion phenomenon depend on the screw angle of inlet impeller. Also, we investigate the separation condition and the resident times that are functions of the phase ratio and density.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.364.1-364
• /
• 2002

This work is concerned with the damage size estimation by using propagating bonging wave signals in a beam. To this end, we apply the continuous wavelet transforms to the incident waves and the reflected waves from a small damage in a long cylindrical beam. In particular, we propose to use the relative magnitudes of the two kinds of waves along the ridges in the wavelet transformed time-frequency planes. (omitted)