• Economic and Environmental Geology
• /
• v.55 no.1
• /
• pp.97-109
• /
• 2022

This study focused on the physicochemical effects of bottom ash dissolved precipitation on the soil and groundwater environment. The iced column and percolation experiments showed that most of the bottom ash particles were drained as the ash-dissolved solution, while the charcoal powder was filtered through the soil. Ion species of Al, As, Cu, Cd, Cr, Pb, Fe, Mn, Ca, K, Si, F, NO₃, SO₄ were analyzed from the eluates collected during the 24 h column test. In the charcoal powder eluates, a high concentration of K was detected at the beginning of the reaction, but it decreased with time. The concentrations of Al and Ca were observed to increase with time, although they existed in trace amount. In the bottom ash eluates, the concentrations of Ca and SO₄ decreased by 30 mg·L^-1 and 67 mg·L^-1, respectively, over 24 h. It is regarded that the infiltration patterns of the bottom ash and biochar in the unsaturated zone were different owing to their particle sizes and solvent properties. It is expected that a significant amount of the bottom ash will mix with the precipitation and percolate below the water table, especially in the case of thin and highly permeable unsaturated zone. The biochar was filtered through the unsaturated zone. The biochar did not dissolve in the groundwater, although it reached the saturation zone. For these reasons, it is considered that the direct contamination by the bottom ash and biochar are unlikely to occur.

• Journal of Appropriate Technology
• /
• v.6 no.2
• /
• pp.174-182
• /
• 2020

The permissible limit of ammonia concentration in drinking water recommended by the World Health Organization (WHO) is 1.5 mg/L. However, in the case of groundwater in Kathmandu, Nepal, the concentration of ammonia fluctuates dramatically from 0 to 120 mg/L at different locations and groundwater depths (Chapagain et al., 2010). Such a high concentration of ammonia causes aesthetic problems in drinking water, such as bad taste and odor; hence, prior treatment is required. In Kathmandu, half of the population utilizes groundwater, which is also employed for drinking water, but owing to a lack of knowledge of household water filters, residents of Kathmandu tend to depend greatly on commercially available jar water than on the installation of a proper household filtration method. Thus, in our study, we employed adsorption and reverse osmosis (RO) as two of the most viable decentralized/household treatment options to address the issue of high contamination of ammonia in drinking water. We evaluated their performances from technical and the economic perspectives using synthetically prepared groundwater at varying ammonia concentrations (50 mg/L and 15 mg/L). Consequently, it was found that adsorption via ion exchange (IE) resin was a comparatively better ammonia removal technology than RO, with 100% ammonia removal even after regeneration; the removal by RO was limited to up to 90%. Furthermore, our study suggests that IE is the most suitable ammonia removal technology for places with lower water consumption (< 50 L/day), whereas RO seemed to be a cost-effective technology for places with higher water consumption, where the daily water demand exceeds 50 L/day. Lastly, these assessments suggest that installing a suitable household treatment system would be more efficient and sustainable from both technical and economic points of view than purchasing commercially bottled water.

• Korean Journal of Poultry Science
• /
• v.49 no.4
• /
• pp.211-220
• /
• 2022

Poultry are exposed to extremely high levels of oxidative stress as a consequence of the excessive production of reactive oxygen species (ROS) induced by endogenous and exogenous stressors, such as high-stocking densities, thermal stress, environmental and feed contamination, along with factors associated with intensive breeding systems. Oxidative stress promotes lipid peroxidation, DNA damage, and inflammation, which can have detrimental effects on the health of birds. During the course of evolution, birds have developed antioxidant defense mechanisms that contribute to maintaining homeostasis when exposed to endogenous and exogenous stressors. The primary antioxidant defense systems are enzymatic and non-enzymatic in nature and play roles in protecting cells from ROS attack. Recently, plant flavonoids, which have been established to reduce oxidative stress, have been attracting considerable attention as potential feed additives. Flavonoids are a group of polyphenolic compounds that can be stabilized by binding structural compounds with ROS, and can promote the elimination of ROS by inducing the expression of antioxidant enzymes. However, although flavonoids can contribute to reducing lipid peroxidation and thereby enhance the antioxidant capacity of birds, they have low solubility in the gastrointestinal tract, and consequently, it is necessary to develop a delivery technology that can facilitate the effect intestinal absorption of these compounds. Furthermore, it is important to determine the dietary levels of flavonoids by assessing the exact antioxidant effects in the gastrointestinal tract wherein the concentrations of dietary flavonoids are highest. It is also necessary to examine the expression of transcriptional factors and vitagenes associated with the efficient antioxidant effects induced by flavonoids. It is anticipated that the application of flavonoids as natural antioxidants will become a particularly important field in the poultry industry.

• Journal of Food Hygiene and Safety
• /
• v.37 no.3
• /
• pp.159-165
• /
• 2022

In this study, heavy metals (lead, cadmium, and mercury) and shellfish poisoning toxins (diarrhetic shellfish poisoning toxins, amnesic shellfish poisoning toxins) were investigated in a total of 104 shellfishes. According to the analysis of heavy metals, lead (Pb) was detected in the range of 0.0177-0.5709 mg/kg, cadmium (Cd) was detected in the range of 0.0226-1.4602 mg/kg, and mercury (Hg) was detected in the range of 0.0015-0.0327 mg/kg. Levels of Pb, Cd, and Hg were acceptable by Korean standards. Okadaic acid (OA) and dinophysistoxin-1 (DTX-1) were investigated for monitoring of diarrhetic shellfish poisoning toxins and OA and DTX-1 were not detected. As a result of monitoring of amnesic shellfish poisoning toxins, domoic acid was detected in 5 of 104 samples and detection ratio was 4.8%. The detection period was found as follows; 1 case in January, 1 case in February, 1 case in May, 2 cases in September. These showed that continuous monitoring for the management of shellfish poisoning toxins and heavy metals is required. In addition, this study can be used as reference data to strengthen managing heavy metals in fishery products.

• Journal of Wetlands Research
• /
• v.24 no.3
• /
• pp.204-212
• /
• 2022

The LID technique began to be applied in Korea after 2009, and LID facilities are installed and operated for rainwater management in business districts such as the Ministry of Environment, the Ministry of Land, Infrastructure and Transport, and LH Corporation, public institutions, commercial land, housing, parks, and schools. However, looking at domestic cases, the application cases and operation periods are insufficient compared to those outside the country, so appropriate design standards and measures for operation and maintenance are insufficient. In particular, LID facilities constructed using LID techniques need to maintain the environment inside LID facilities because hydrological and environmental effects are expressed by material circulation and energy flow. The LID facility is designed with the treatment capacity planned for the water circulation target, and the proper maintenance, vegetation, and soil conditions are periodically identified, and the efficiency is maintained as much as possible. In other words, the soil created in LID is a very important design element because LID facilities are expected to have effects such as water pollution reduction, flood reduction, water resource acquisition, and temperature reduction while increasing water storage and penetration capacity through water circulation construction. In order to maintain and manage the functions of LID facilities accurately, the current state of the facilities and the cycle of replacement and maintenance should be accurately known through various quantitative data such as soil contamination, snow removal effects, and vegetation criteria. This study was conducted to investigate the current status of LID facilities installed in Korea from 2009 to 2020, and analyze soil changes through the continuity and current status of LID facilities applied over the past 10 years after collecting soil samples from the soil layer. Through analysis of Saturn, organic matter, hardness, water contents, pH, electrical conductivity, and salt, some vegetation-type LID facilities more than 5 to 7 years after construction showed results corresponding to the lower grade of landscape design. Facilities below the lower level can be recognized as a point of time when maintenance is necessary in a state that may cause problems in soil permeability and vegetation growth. Accordingly, it was found that LID facilities should be managed through soil replacement and replacement.

• Economic and Environmental Geology
• /
• v.55 no.5
• /
• pp.511-519
• /
• 2022

In order to develop an air-stripping based remediation process to remove the TOC (Total Organic Carbon) in groundwater around the underground LPG storage cavern, the laboratory scale experiments at various conditions (change of air injection volume and temperature, the application of ultrasonic treatment, etc.) for two types of groundwater (initial TOC concentration of 608 mg/L and 153 mg/L, respectively). From results of experiment, as the air injection rate for stripping into groundwater increased from 2 L/min to 11 L/min and as the air-stripping time increased from 1 hour to 24 hour, the TOC removal efficiency of air-stripping increased. However, the TOC concentration of treated groundwater was higher than the discharge tolerance limit (100 mg/L) even after 24 hour stripping at the maximum air injection rate of 11 L/min. The main compounds of the TOC in groundwater were identified as methanol and propane and the long stripping time (more than 24 hour) was needed to separate the methanol from groundwater because of the affinity between water and methanol. At 20℃ and 4 L/min of air injection, the TOC removal efficiency increased to 59.1% after 24 hour air-stripping. When the temperature of groundwater increased to 30℃ and 40℃, the TOC removal efficiency increased up to 80.0% and 82.8%, suggesting that more than 24 hour air-stripping at 40℃ is needed to lower the TOC concentration to below 100 mg/L and the additional TOC removal process as well as the air-stripping is necessary. When the temperature increased to 60℃ and the ultrasonic treatment was conjugated with the air-stripping, the TOC removal efficiency increased to 87.8% within 5 hour stripping and the final TOC concentration (72.4 mg/L) was satisfied with the TOC discharge tolerance limit. The TOC removal efficiency for groundwater having low TOC concentration (153 mg/L) also showed similar removal efficiency of 89.7% (the final TOC concentration: 18.9 mg/L). Results in this study supported that the air-stripping conjugated with the ultrasonic treatment could remove successfully the TOC in groundwater around the underground LPG strorage cavern.

• Korean Journal of Environmental Biology
• /
• v.41 no.2
• /
• pp.109-125
• /
• 2023

This study was conducted to select target fish species as baseline research for accumulation analysis of major hazardous chemicals entering the aquatic ecosystem in Korea and to analyze the impact on fish community. The test bed was selected from a sewage treatment plant, which could directly confirm the impact of the inflow of harmful chemicals, and the Geum River estuary where harmful chemicals introduced into the water system were concentrated. A multivariable metric model was developed to select target candidate fish species for hazardous chemical analysis. Details consisted of seven metrics: (1) commercially useful metric, (2) top-carnivorous species metric, (3) pollution fish indicator metric, (4) tolerance fish metric, (5) common abundant metric, (6) sampling availability (collectability) metric, and (7) widely distributed fish metric. Based on seven metric models for candidate fish species, eight species were selected as target candidates. The co-occurring dominant fish with target candidates was tolerant (50%), indicating that the highest abundance of tolerant species could be used as a water pollution indicator. A multi-metric fish-based model analysis for aquatic ecosystem health evaluation showed that the ecosystem health was diagnosed as "bad conditions". Physicochemical water quality variables also influenced fish feeding and tolerance guild in the testbed. Eight water quality parameters appeared high at the T1 site, indicating a large impact of discharging water from the sewage treatment plant. T2 site showed massive algal bloom, with chlorophyll concentration about 15 times higher compared to the reference site.

• Clean Technology
• /
• v.29 no.1
• /
• pp.31-38
• /
• 2023

Due to water shortages caused by water pollution and climate change, total organic carbon (TOC) standards have been implemented for wastewater discharged from public sewage treatment facilities. Furthermore, there is a growing interest and body of research pertaining to the reuse of sewage treatment water as a secure alternative water resource. The membrane bio-reactor (MBR) method is commonly used for advanced wastewater treatment because it can remove organic and inorganic ions and it does not require or emit any chemicals. However, the MBR process uses a separation membrane (MF), which requires frequent film cleaning due to fouling caused by a high concentration of mixed liquor suspended solid (MLSS). In this study, process improvement and microbubble cleaning efficiency were evaluated to improve the differential pressure, water flow, and MF fouling, which are the biggest disadvantages of operating the MF. The existing MBR method was improved by installing a precipitation tank between the air tank and the MBR tank in which raw water was introduced. Microbubbles were injected into a separation membrane tank into which the supernatant water from the precipitation tank was introduced. The microbubble generator was operated with a 15 day on, 15 day off cycle for 5 months to collect discharged water samples (4L) and measure TOC. As the supernatant water from the precipitation tank flowed into the separation membrane tank, about 95% of the supernatant water MLSS was removed so the MF fouling from biological contamination was prevented. Due to the application of microbubbles to supernatant water from the precipitation tank, the differential pressure of the separation membrane tank decreased by 1.6 to 2.3 times and the water flow increased by 1.4 times. Applying microbubbles increased the TOC removal rate by more than 58%. This study showed that separately operating the air tank and the separation membrane tank can reduce fouling, and suggested that applying additional microbubbles could improve the differential pressure, water flow, and fouling to provide a more efficient advanced treatment method.

• Korean Journal of Environment and Ecology
• /
• v.36 no.6
• /
• pp.566-574
• /
• 2022

Heavy metals are one of the dangerous pollutants that threaten urban biodiversity due to their accumulation over a long period without being decomposed in vivo. Accordingly, there is a need for biological monitoring to compare accumulation concentrations in living organisms according to the degree of heavy metal exposure to evaluate heavy metal contamination in the air in urban areas. This study aims to examine the possibility of using nesting materials as heavy metal monitoring samples and determine the effects of heavy metals on Paridae. We installed 54 artificial nest boxes in the research areas that included campus green spaces (14), urban forests (11), and urban parks (29) on a university campus in Cheonan City, Chungcheongnam Province. The birds' use rate of artificial nest boxes was 11/14 (78.57%) in campus green spaces, 8/11 (72.72%) in urban forests, and 6/29 (20.68%) in urban parks. Moss materials were collected from collected nests, and the heavy metal accumulation characteristics of each type of urban green space and the effects of heavy metals on the success of fledging of Paridae were compared through heavy metal analysis. The analysis showed that the average concentrations of zinc and lead were 228.08±209.62 ㎍/dry g and 17.67 ± 6.72 ㎍/dry g, respectively. There was no significant difference in zinc concentration for each type of urban green space (Kruskal-Wallis test, p-value=0.28), but lead concentration showed a significant difference (Kruskal-Wallis test, p<0.05^*). Of the 21 Paridae, nests analyzed for heavy metals, fledging of birds was observed in 11 nests (52.38%). Fledging of birds observed in each urban green space type was 7 campus green spaces (77.78%), 6 in urban forests (85.71%), and 1 in urban park (20%), mainly in urban forests and green spaces on campus. Heavy metal concentrations were compared to check the effect of heavy metal accumulation on the successful fledging of Paridae, but there was no statistically significant difference (Zn: W=44, p-value=0.74, Pb: t=0.64676, df =7.2422, p-value=0.54). This study is a basic study using the nesting materials of Paridae as heavy metal monitoring samples, and it is determined that it can be used as basic data for non-invasive biological monitoring.

• Journal of Korean Society of Forest Science
• /
• v.112 no.2
• /
• pp.157-172
• /
• 2023

Controlled pollination (CP) is an important method in tree breeding programs because CP quickly generates desirable genotypes and rapidly maximizes genetic gains. However, few studies have evaluated the efficiency and success rate of CP in the breeding program of Pinus densiflora. To evaluate CP and the management of control pollinated progenies, we used 159 individuals in CB2 × KW40 or KW40 × CB2 populations that were established in 2015. After genotyping microsatellite loci, we estimated whether the number of primers was sufficient or not. Then, we performed pedigree analysis. The result showed that the number of primers was sufficient. By pedigree analysis, we found out that 60 of 159 individuals had been generated by the mating between CB2 and KW40. In the maternity analysis, there was evidence to indicate the possibility of management problems. Therefore, we excluded 54 individuals and repeated the pedigree analysis. In the second analysis, 47 of 105 individuals were generated by the mating between CB2 and KW40. To increase the efficiency of CP in tree breeding programs, several precautions are required. It is necessary to identify the exact clone names of the mother and father trees. In addition, CP processes should be performed properly, including deciding on the schedule of CP and the isolation of female strobili or flowers. Finally, the monitoring of hybrid progenies management after mating is important. Molecular markers should be used to identify the clone names of the mother and father trees and for monitoring post hoc management. This study provides a reference for tree breeding programs for the future control pollination of pine species.