• 소음진동
• /
• 제9권2호
• /
• pp.317-323
• /
• 1999

Dynamic characteristics of catenary that supplies electrical power to high-speed trains are investigated. A simple catenary is composed of the contact and messenger wires connected by droppers possessing bi-directional stiffness properties. For slender, repeating structures such as catenary, both the wave propagation and vibration properties need to be understood. The influence of parameters that determine catenary dynamics are investiaged through numerical simulations involving finite element models. The effects of the tension and flexural rigidity of the contact wire is first investigated. The effects of dropper characteristics are then investigated. For linear droppers wave propagation as well as modal properties are determined. For large catenary motion, droppers can be modeled as bi-directional elements possessing low stiffness in compression and high stiffness in tension. For this case, impulse response is computed and compared with the cases of linear droppers. It is found that the catenary dynamics are primarily determined by contact wire tension and dropper properties, with large responses observed in 5∼40 Hz frequency range. In particular, the dropper stiffness and spacing are found to have dominant influence on the response frequency and the wave transmission characteristics.

• 전기의세계
• /
• 제18권6호
• /
• pp.23-32
• /
• 1969

The thesis has derived the formulas and computational algorithms useful for predicting and constraining the potential rises on the neutral line in 3-phase, 4-wire distribution line systems in the case of contact faults and single-line grounding faults. In addition it has suggested economically optimal designing conditions herewith of the distribution line systems in conduction with the potential restraining cost functions.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.909-914
• /
• 2004

This study investigate the cause analysis on fracture of dropper clamp in catenary system. Dropper clamp is using as a holder between messenger wire and contact wire in catenary system. To analyze the cause analysis on fracture of dropper clamp, we have conducted experiment such as tension withstand strength test, holding strength test of a new products, SEM and EDX of field fractured specimens.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 추계학술대회 논문집
• /
• pp.1279-1284
• /
• 2008

This paper presents the operating characteristic of high voltage impulse(HVI) track circuit owing to the ill-contact of impedance bond lead wire. The characteristic operations of the track include rail voltage and current. Measurements are carried out using oscilloscope with current probe and it analyzed the abnormal operation due to connector of protective wire. Finally, suitable track circuit is proposed for conventional line, and operating characteristic of HVI track circuit is affected by bypass circuit.

• Design & Manufacturing
• /
• 제10권1호
• /
• pp.19-25
• /
• 2016

Connectors are very important components that transmit electric signals to different parts. It must maintain intensity of the connector to prevent defects from impact and maintain contact to transmit electric signals. Most of the external parts of the connector, which act as the main framework, are formed by injection molding. However, bend deformation occurs for injection molded products due to the residual stress left inside the product after product molding. When the bend deformation is large, it does not come into complete contact when being assembled with other parts, which leads to connector contact intensity not being properly maintained. In result, the main role of the connector, which is to transmit electric signals, cannot be performed. In order to address this problem, this study conducted bend deformation cause analysis through bend deformation analysis to predict and prevent bend deformation of housings and wafers, which are injection molded products of pressure welded connectors that are normally applied in compact mobile and display products. Bend deformation analysis was carried out by checking the charging time, pressure distribution and temperature distribution through wire to board connector wafer and housing injection molding analysis. Based on the results of the bend deformation analysis results, the cause of the bend deformation was analyzed through deformation resulting from disproportional cooling, deformation resulting from disproportional contraction, and deformation resulting from ingredient orientation. In result, it was judged that the effects for bend deformation were biggest due to disproportional contraction for both the pressure welded connector wafer and housing.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2006년도 추계학술대회 논문집
• /
• pp.821-831
• /
• 2006

There are 5 railway bridges in a Seoul metro network; Jamsil, Dangsan(line 2), Dongho(line 3), Dongjak(line 4) and Chungdam(line 7). Because there are strong wind and vibration in the bridges, uplift of a contact wire caused by pantographs in the bridge section is higher than in a normal section. If the uplift at the support point exceed 10 cm, an interference between pantographs and catenary system happens. Estimated maximum uplift is obtained by applying safety factor 2 to the simulation results. The application of the safety factor is needed for taking into account of the effect of the wind, etc. Previously, we can not check whether or not the safety factor is proper. Recently, we can measure the uplift during the train operation, as a telemetry system which can measure dynamic behavior of the contact wire has been developed. The aim of this research is to review how proper the safety factor related to the uplift is, based on the measurement. We performed simulations and experiments for the uplift at the Jamsil railway bridge. The simulations were performed for the every kind of the train passing the Jamsil bridge. In order to compare the analysis results with the measurement results, we measured the uplifts at the support when the trains passed the measuring point. Finally, we proposed adequate safety factor with the uplift for the bridge section.

• 대한토목학회논문집
• /
• 제33권4호
• /
• pp.1281-1293
• /
• 2013

현수교 주케이블용 평행강선 스트랜드(PPWS) 소켓의 엄밀한 수치해석을 위한 유한요소해석 모델을 제안하였고, 제안된 해석 모델을 이용하여 소켓의 거동을 분석하였다. 개별 강선과 소켓 내부 주입 합금재의 영향을 고려한 직교 이방성 재료 모델을 적용하였고, Coulomb 마찰 및 표면접촉 모델을 도입하여 소켓 내면과 주입 합금재 표면의 접촉 상태를 구현하였다. 인장 실험으로부터 측정된 소켓 외면의 변형율과 유한요소 해석 결과를 비교하여 제안된 유한요소 해석 모델의 타당성을 검증하였고, 마찰계수의 변화에 따른 소켓의 거동을 해석하였다. 해석 결과, 소켓 내면과 주입 합금재 표면의 마찰은 소켓과 주입 합금재에 발생하는 응력 집중을 크게 완화 시켰으며, 소켓 설계법에서 정의된 수직응력식은 소켓 내면과 주입 합금재 표면의 접촉응력 분포에서 상하부 사분위값의 평균을 대표하는 것으로 나타났다.

• International Journal of Aeronautical and Space Sciences
• /
• 제17권3호
• /
• pp.285-295
• /
• 2016

A contact strip shape of a high speed train pantograph system was optimized with CFD to increase the aerodynamic performance and stability of contact force, and the results were validated by a wind tunnel test. For design of the optimal contact strip shape, a Kriging model and genetic algorithm were used to ensure the global search of the optimal point and reduce the computational cost. To enhance the performance and robustness of the contact strip for high speed pantograph, the drag coefficient and the fluctuation of the lift coefficient along the angle of attack were selected as design objectives. Aerodynamic forces were measured by a load cell and HWA (Hot Wire Anemometer) was used to measure the Strouhal number of wake flow. PIV (Particle Image Velocimetry) was adopted to visualize the flow fields. The optimized contact strip shape was shown a lower drag with smaller fluctuation of vertical lift force than the general shaped contact strip. And the acoustic noise source strength of the optimized contact strip was also reduced. Finally, the reduction amount of drag and noise was assessed when the optimized contact strip was applied to three dimensional pantograph system.

• Composites Research
• /
• 제13권6호
• /
• pp.39-46
• /
• 2000

방전가공은 공구와 공작물 사이의 얇은 간극에 전류를 방전시켜 금속을 가공하는 방법이다. 방전 와이어 가공은 전도성 와이어를 사용하는 방전가공의 특수한 예로서, 펀치나 금형제조에 널리 이용되고 있다. 와이어 방전가공에서 와이어는 와이어 가이드 및 외팔보로서 지지되어 있다. 최근 생산성의 증가추세와 더불어 와이어의 이송속도가 증가함에 따라 외팔보의 진동 등으로 인한 기계 정밀도의 저하가 우려된다. 본 논문에서는 정, 동특성이 우수한 방전가공기용 복합재료 외팔보를 설계, 제작하였다. 끼워맞춤길이와 보강 적층수의 변화에 따른 정, 동특성의 변화를 살펴보기 위하여 시편을 제작하여 하중실험을 수행하였다. 또한 유한요소 해석을 수행하여 하중실험의 결과와 상호 비교하였다. 시편실험의 결과로부터 방전가공기용 복합재료 외팔보를 설계, 제작하여 기존의 금속 외팔보와 그 성능을 상호 비교하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 춘계학술대회 논문집 전기설비전문위원
• /
• pp.71-74
• /
• 2005

At the neutral sections, There are neutral sections inserted in overhead contact line between the substations to divide different phase current sections of AC electrified lines. except convention line, a large stress occurs in the contact wire near the fittings under passing pantographs. So, in order to raise the train speed over 150km/h, a new type section has been adopted.