• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.05a
• /
• pp.295-298
• /
• 2012

Repair and strengthening is necessary to extend the service life of existing buildings. Polymer-modified cement mortar (PCM) has been extensively used as a high performance material particularly for finishing and repairing works in concrete building because of itsexcellent adhesion, waterproofing, resistance to chemical attack, and workability. As PCM contains organic polymer, it is necessary to clarify its properties at high temperature under fire, on which sufficient data are not available. This paper evaluated the burn-up characteristics of polymer-modified cement mortar with cone calorimeter test, non-combustibility test and flammability test with experimental parameters such as the types of polymer, unit-polymer content, polymer-cement ratio and thickness of the specimen.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.05a
• /
• pp.99-100
• /
• 2019

Water repellent and waterproofing agents fail to act work properly if cracks or detachment occurs outside. The method of making mortar was tested by classifying it into two methods: direct water-repellent put in concrete and water-repellent spray to sand method. It was found that the compressive strength was decreased as the amount of water repellent was increased. As a result of measuring the contact angle, all of the specimens were hydrophobic. The spray method showed greater water repellent effect than the direct mixing method.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.05a
• /
• pp.190-191
• /
• 2019

In complex waterproofing method, the stability of the joint is an important factor. The joints should not be broken for repeated movements and tensile forces. Therefore, we tried to confirm the stability of joints in newly developed joints and general joints. Repeated fatigue resistance performance tests and joint tensile strength tests were carried out on four types of joints. The fatigue resistance performance test showed no abnormality in all four types. It was confirmed that the newly developed top-down joint has higher stiffness than existing joints.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.05a
• /
• pp.217-218
• /
• 2019

In this study, to overcome the limitation of material application as the surface layer of bridge decks (asphalt concrete, concrete), a newly developed waterproof sheet is proposed to be usable for both asphalt concrete and concrete. Subsequent tensile bond strength was tested, and the test results showed that the tensile bond strengths were similar to depending on the type of the surface layer material for bridge decks, confirming the applicability of the proposed material.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.11a
• /
• pp.175-176
• /
• 2018

In this study, the performance of acrylate was evaluated by using acrylate composite waterproof sheet. Through this experiment, the waterproof sheet plays a primary role of waterproofing. When the water leakage occurs, the acrylate reacts with water and expands, and the performance of the self repairing of the damaged part is confirmed by temperature.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.11a
• /
• pp.183-184
• /
• 2018

In this study, an inflated resistance test is conducted out of the nine test items of KS F 2622 using an appropriate series of waterproof materials, and the results are reported and compared to the performance range presented in the KS F 2622 inflated resistance test.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.11a
• /
• pp.4-5
• /
• 2018

The water proofing sheet of synthetic polymer applies to the purification plant, the wastewater treatment center, the low waterway, the dosing tanks, etc, and when we construct these, we apply the dual waterproof by means of hot air staking welder or extruder. However, the experts skilled in the hot air welding or extruder does not use them, it can be a quality problem. Therefore, in this study, it is the purpose to verify whether the semi-automatic hot air staking welder and automatic extruder that can construct the waterproof sheet is possible in field even if it is not a professional specialist.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.11a
• /
• pp.187-188
• /
• 2018

In this study, wind pressure resistance test was carried out among the nine test items of KS F 2622 using five types of water-tight material. After comparing the results with the performance range of the current KS F 2622 wind pressure resistance test, it is recommended to check the adequacy of the addition of the combined series.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.11a
• /
• pp.817-820
• /
• 2004

Our country was much developments in change of construction environment along with fast economy development. But, various problems that must think in problem of safety and quality were appeared. Constructions which build through rapid economy development are getting many social criticisms to problem of crack and water leakage at use process. Is situation that huge repair expense to cure this is engaged. Safety problem of construction is indicated socially through various media mediums again.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.11a
• /
• pp.126-127
• /
• 2017

This study investigates the effect of improving the heat resistance performance when carbon fiber is mixed in the polyurea coating material. A tensile strength test method was carried out with the carbon fiber mixed polyurea specimens at an interval of 7, 14, and 21 days after heat treatment at 140±2℃. The test results showed that there was a significant decrease in the tensile strength performance. While the elongation and tensile performance decreased greatly, it was confirmed nevertheless the overall performance was maintained. This study proposes that mixing carbon fiber to the polyurea resin can effectively secure long-term heat resistance, thereby solving the problem of deterioration of physical properties caused by exposure to ultraviolet rays.