• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.12
• /
• pp.23-32
• /
• 2020

This study investigated the thermal degradation and fading behavior of PTT dyed with vat dye and its dyeing ability. The PTT sample was dyed with vat dye using an acid treatment and pad-steam method to improve the dyeing performance. This method made dye particle nanosize and allowed it to penetrate the polymer material easily. The sample dyed using the pad-steam method showed level dyeing and enhanced dyeing affinity, compared to the batch-dyeing method. The degradation behavior of PTT dyed with vat dye after each heat and UV treatment was examined with the change in tensile strength or K/S value on the sample. The tensile strength and K/S values of the sample dyed with vat dye after the heat and UV treatment decreased with increasing temperature and exposure time. Although they showed high degradation under severe conditions, its rate constant was improved compared to the samples dyed with disperse dye. Consequently, acid treatment and the pad-steam method resulted in the introduction of vat dye on PTT. In addition, the PTT dyed with vat dye showed enhanced thermal and UV resistance because of their high molecular weight and chemical structure for stable adsorption behavior.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.31 no.1
• /
• pp.24-31
• /
• 2021

We report structural, mechanical, and thermal properties of diecast ADC12 aluminum alloys characterized using synchrotron X-ray diffraction (XRD), scanning electron microscopy, energy dispersive X-ray (EDX) analysis, thermal conductivity (λ), Vickers hardness (Hv), and stress-strain measurements. We also studied the effect of post-annealing performed in a vacuum atmosphere on the mechanical properties of diecast ADC12 alloys. EDX and XRD results revealed that Al2Cu and AlCu3 grains are formed, well dispersed in Al base and highly crystalline. Ultimate tensile strength (UTS) of 307.9 ± 9.1 MPa and elongation of 2.98 ± 0.62 % were estimated. λ was 129.3 ± 0.27 W/m·K and Hv was approximately 130. Both values were significantly higher than the reported values. At annealing temperatures ranging from 25 to 200℃, UTS and Hv values remained constant, while as the annealing temperature increased to 500℃, these values gradually decreased. This is because stabilization of the microstructure improves toughness and ductility.

• Korean Chemical Engineering Research
• /
• v.60 no.2
• /
• pp.175-183
• /
• 2022

With the expansion of the automobile market, the demand for Nd as an essential rare earth material for automobile motors is rapidly increasing. Research on the calcio-thermic reduction process between Nd₂O₃ and calcium-based alloys has been extensively studied in order to manufacture Nd. In this study, Ca-Cu, as a reducing for Nd₂O₃, was prepared by electrolysis in CaCl₂ molten salt. Cu wire and graphite were employed as a working electrode and a counter electrode for electrolysis reaction, respectively. The reference electrode was manufactured by putting Ag wire in a mixture of AgCl and CaCl₂ at a ratio of 1:99 mol%. The cyclic voltammetry results showed that the deposition of Ca²⁺ on the surface of working electrode was observed from a potential of -1.8 V, and the reduction potential of Ca²⁺ decreased as the reaction temperature increased. The diffusion coefficient of Ca²⁺ calculated by the chronoamperometry experiment was found to be 5.4(±6.8)×10^-6 cm²/s. In addition, Ca-Cu liquid alloy was prepared by applying a constant potential to Cu electrodes. The element ratio of Ca-Cu alloy formed by applying a potential of -2.0 V was found to Ca:Cu=1:4.

• Tunnel and Underground Space
• /
• v.31 no.6
• /
• pp.610-622
• /
• 2021

The DECOVALEX project is one of the representative international cooperative projects to enhance the understanding of the complex Thermo-Hydro-Mechanical-Chemical(THMC) coupled behavior in the high-level radioactive waste disposal system based on the numerical simulation. DECOVALEX-2023 is the current phase consisting of 7 tasks, and Task C aims to model the THM coupled behavior in the disposal system based on the Full-scale Emplacement (FE) experiment at the Mont-Terri underground rock laboratory. This study performs the numerical simulation based on the OGS-FLAC developed for the current study. In the numerical model, we emplaced the heater with constant power horizontally based on the FE experiment and monitored the pressure development, temperature increase, and mechanical deformation at the specific monitoring points. We monitored the capillary pressure as the primary effect inducing the flow in the buffer system, and thermal stress and pressurization were dominant in the surrounding rocks' area. The results will also be compared and validated with the other participating groups and the experimental data further.

• Journal of Plant Biotechnology
• /
• v.49 no.3
• /
• pp.222-229
• /
• 2022

Apples are the most grown fruit crops in the fruit industry of Korea. However, virus or viroid infection such as apple mosaic virus (ApMV), apple stem grooving capillovirus (ASGV), apple stem pitting virus (ASPV), apple chlorotic leaf spot virus (ACLSV), apple scar skin viroid (ASSVd) causes fruit yield reduction and poor fruit quality. Therefore, in this study, we examined to established an efficient virus-free system to eliminate the most infected ASGV virus in domestic apple orchard. We investigated that the shoot growth rate and the virus removal rate in ASGV infected potted apples that were treated with heat treatment in a growth chamber (constant temperature/humidity device) maintained at 36℃, 38℃ and 40℃ for 4 weeks. Here we found that the shoot growth rate was the highest in the heat treatment group (36℃) and the virus was removed in the middle and top of the shoot but not in the bottom. The virus was did not removed in the 38℃ and 40℃ heat treatment group in all section of shoots, and the heat treatment group (40℃) died after 4 weeks of heat treatment without growth of shoots. We performed in vivo shoot-tip grafting using the shoot-tip of potted apple heat-treated at 36 ℃, and we also investigated the viability and virus removal rate, which showed 94% viability and 20% virus removal rate. Collectively, our results suggest that it would be possible to produce the virus-free apple plants through heat treatment and shoot-tip grafting.

• Applied Chemistry for Engineering
• /
• v.33 no.5
• /
• pp.477-481
• /
• 2022

As a part of improving the quality of crude methylnaphthalene (CMNO), this study was experimentally examined the reduction of nitrogen-containing compounds (NC) present in the CMNO by solvent extraction. The CMNO was composed of three kinds of NC [quinolone (QU), iso-quinoline (IQU), indole (IN)], three kinds of bicyclic aromatic compound [BAC; naphthalene (NA), 1-methylnaphthalene (1MNA), 2-methylnaphthalene (2MNA)] and biphenyl (BP) etc., in addition to an aqueous formamide solution, which were used as raw materials and a solvent, respectively. The increase in the volume fraction of water to the solvent in the initial state (y_w,0) caused a sharp decrease in the distribution coefficient and the yield of NC, but conversely raised the increased selectivity of NC based on 2MNA. The compositions of QU, IQU and IN in the raffinate oil recovered through the equilibrium extraction of batch co-current 5-stage under constant conditions [y_w,0 = 0.1, volume fraction of solvent to feed (CMNO) at the initial state = 1, operating temperature = 303 K, liquid-liquid contacting time = 72 h] were reduced by about 51.5%, 55.2%, and 71.8%, respectively, when compared to those of CMNO. From the excellent reduction rate of NC, the formamide extraction method suggested in this study can be expected to be a useful reduction method for NC contained in the CMNO.

• Korean Chemical Engineering Research
• /
• v.59 no.2
• /
• pp.239-246
• /
• 2021

Characteristics of hydrodynamics and heat absorption by gas in a directly-irradiated fluidized bed particle receiver (50 mm-ID X 150 mm high) of SiC particles have been determined. Solid holdups of SiC particles show almost constant values with increasing gas velocity. Fine SiC particles (SiC II; dp=52 ㎛, ρs=2992 kg/㎥) showed low values of relative standard deviation of pressure drop across bed but high solids holdups in the freeboard region compared to coarse SiC particles (SiC I; dp=123 ㎛, ρs=3015 kg/㎥). The SiC II exhibited higher values of temperature difference normalized by irradiance due to the effect of additional solar heat absorption and heat transfer to the gas by the particles entrained in the freeboard region in addition to the efficient thermal diffusion of the solar heat received at bed surface. Heat absorption rate and efficiency increased with increasing the gas velocity and fluidization number. The SiC II showed maximum heat absorption rate of 17.8 W and thermal efficiency of 14.8%, which are about 33% higher than those of SiC I within the experimental gas velocity range.

• Resources Recycling
• /
• v.31 no.3
• /
• pp.61-72
• /
• 2022

We investigated the electrochemical behavior of Sn (93.0 %)-Ag (4.06 %)-Cu (0.89 %) during electrolysis of Pb-free solder waste to recover tin and silver. A thin strip of the solder waste produced by high-temperature melting and casting was used as a working electrode to perform electrochemical analysis. During anodic polarization, the current peak of an active region decreased with an increase in the concentration of sulfuric acid used as an electrolyte. This resulted in the electro-dissolution of the working electrode in the electrolyte (1.0 molL^-1 sulfuric acid) for a constant current study. The study revealed that the thickening of an anode slime layer at the working surface continuously increased the electrode potential of the working electrode. At 10 mAcm^-2, the dissolution reaction continued for 25 h. By contrast, at 50 mAcm^-2, a sharp increase in the electrode potential stopped the dissolution in 2.5 h. During dissolution, silver enrichment in the anode slime reached 94.3% in the 1 molL^-1 sulfuric acid electrolyte containing a 0.3 molL^-1 chlorine ion, which was 12.7% higher than that without chlorine addition. Moreover, the chlorine enhanced the stability of the dissolved tin ions in the electrolyte as well as the current efficiency of tin electro-deposition at the counter electrode.

• Applied Chemistry for Engineering
• /
• v.33 no.4
• /
• pp.431-435
• /
• 2022

The reduction of nitrogen-containing compounds (NC) containing the model crude methylnaphthalene oil (CMNO) of 5 compounds system was experimentally studied by solvent extraction. The model CMNO consisting of 3 kinds of NC including quinolone (QU), iso-quinoline (IQU), indole(IN) and 2 kinds of bicyclic aromatic compounds such as 1-methylnaphthalene (1MNA), 2-methylnaphthalene (2MNA) as raw materials, as well as the aqueous solution of formamide as a solvent, were used. The increase in the volume fraction of water to the solvent at the initial state (y_w,0) sharply decreased, but the distribution coefficient and the yield of NC conversely increased the selectivity of NC based on 2MNA, and an increase in the volume fraction of solvent to feed (S/F) simultaneously increased the distribution coefficient, yield and selectivity of NC. The yields of QU, IQU and IN under constant conditions (y_w,0 = 0.1, S/F = 1, equilibrium temperature 303 K) were 30%, 31% and 10%, respectively, and selectivity was 15, 15 and 20, respectively. From the excellent yield and selectivity of NC, the formamide extraction method of this study was expected as a method for reducing the NC contained in the model CMNO.

• Applied Chemistry for Engineering
• /
• v.33 no.2
• /
• pp.202-209
• /
• 2022

Effects of the support and amount of NiCl₂ on ammonia adsorption capacity were investigated to improve the ammonia adsorption performance. NiCl₂ was impregnated onto the surface of various supports under ultrasonic irradiation. The physicochemical properties and ammonia adsorption performance of NiCl₂-impregnated adsorbents were investigated. Among the various supports, it was found that the adsorption capacity of ammonia was the best when NiCl₂ was impregnated on activated carbon (AC) with the highest specific surface area. As a result of changing the amount of NiCl₂ impregnated on AC, the NiCl₂(2.0)/AC adsorbent impregnated with 2 mmol·g^-1 of NiCl₂ showed the highest ammonia adsorption capacity of 5.977 mmol·g^-1. In addition, the adsorption capacity was found to be maintained at an almost constant level in five repeated cycle tests under the condition that low-temperature heat could be utilized. This indicates that the adsorbent has excellent regeneration ability.