• Journal of Korean Port Research
• /
• v.12 no.1
• /
• pp.47-53
• /
• 1998

Presently, it was faced with serious social problems as traffic accident, parking violation & traffic congestion due to change of industrial structure, expansion of economic volume, elevation of national life level and rapid motorization. Accordingly, the study is research to improve immidiate transportation problems which could be establish the rating model about consideration degree of evaluation factor based on MDPREF's method in connection with Intelligent Transportation System(ITS)

• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.4
• /
• pp.302-305
• /
• 2021

Selection of the optimal inductance for power factor improvement of a buck AC/DC light-emitting diode (LED) driver with wide input voltage range is described in this study. The power factor change based on the slope compensation is obtained for various normalized output current (NOC) values using discrete-time domain analysis. The possibility of implementing constant slope compensation is described using power factor curves for various NOC values. NOC = 0.5 is chosen for the value of inductance with consideration for the simple implementation and reduction of inductor size. Experimental results of the inductance corresponding to NOC = 0.5 are presented.

• Proceedings of the KSCN Conference
• /
• 2005.04a
• /
• pp.109-110
• /
• 2005

• Journal of the Korean Institute of Gas
• /
• v.4 no.1 s.9
• /
• pp.33-39
• /
• 2000

Stress intensity factor after penetration was discussed experimentally using long surface pre-cracked specimens of aluminum alloy 5083. The propagation behavior evaluation of long surface crack by equation proposed at penetration of short surface crack could be need modification to evaluate precisely because the error was high as aspect ratio is little. The modification of stress intensity factor with consideration of aspect ratio at penetration of long surface crack can be analyzed the behavior of crack penetration quantitatively.

• Journal of radiological science and technology
• /
• v.22 no.2
• /
• pp.57-60
• /
• 1999

Therapy equipment have taken progress for Cancer make use of Radiation for the normal tissue system make much of important for shielding. In modern times independent jaw setting to used equipment as possible make use of asymmetric field. Therefore, the asymmetric field be leave out of consideration wedge factor because of with used wedge for the most of part. These experimentation find out have an effect on the dosimetry of out put compared with of the difference between the symmetric field and asymmetic field for the wedge factor.

• The Journal of the Acoustical Society of Korea
• /
• v.19 no.1E
• /
• pp.38-42
• /
• 2000

In this paper we studied the reduced subjective timbre space of time-varying tones as well as steady state tones. 45 modified test tones were constructed from the original violin tone in consideration of 4 physical factors: spectrum envelope, inharmonicity, time-varying spectrum and time reversal. The semantic differential (SD) method was used in the listening test. According to the factor analysis, the adjectives can be factorized into 4 groups. The first factor is characterized by the adjectives, 'free', 'broad', 'deep', 'rich', 'strong' and 'reverberant', the second by 'tenor', 'clear', 'bright', 'light' and 'sharp', the third by 'easy', 'smooth', and 'solid', the fourth by 'warm' and 'full'. The first factor, 'richness', seems to be dependent upon the time-varying characteristic of a tone. The second factor, 'sharpness', is shown to play an important role in a time-varying tone as well as in a steady state tone.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.3
• /
• pp.7-15
• /
• 2013

In lighting design, the calculation of maintenance factor is performed by calculation considering light source, characteristics of luminaire and environmental factors. The method to calculate the current maintenance factor applied to tunnel lighting design takes into consideration only pollution factors in tunnels. In addition, the calculation method should be change in response to changes of tunnel conditions and used light sources. In this study, the calculated factor of the maintenance factor in tunnel is determine by four calculation factors generally applied to the calculation of maintenance factor. This study examined the method of calculating the maintenance factor of tunnel lighting that can be applied according to the installation conditions in designing tunnel lighting by applying the actual installation data of luminaire.

• Journal of computational fluids engineering
• /
• v.21 no.4
• /
• pp.54-60
• /
• 2016

The valve used in nuclear power plant must be qualified but the limitation of the test facility leads to use the numerical analysis. The flow coefficient is calculated with the consideration of the pressure, velocity and geometry. And the flow coefficient is the important physical property which is prepared using experiment or analysis by valve manufacturer. In this study, the analysis model was made according to ISA 75.02.01 and the mass flow rate and pressure drop ratio was calculated. The model of the expansion factor was applied to the simulation result and the pressure drop ratio at the start of the choked flow in the valve was found. With the simulation result, the consideration was performed that the expansion factor is the important physical property to the system engineer in addition to the flow coefficient.

• Geomechanics and Engineering
• /
• v.15 no.3
• /
• pp.879-888
• /
• 2018

Probability-based design codes have been developed to sufficiently confirm the safety level of structures. One of the most acceptable probability-based approaches is Load Resistance Factor Design (LRFD), which measures the safety level of the structures in terms of the reliability index. The main contribution of this paper is to calibrate the load and resistance factors of the design code for tunnels. The load and resistance factors are calculated using the available statistical models and probability-based procedures. The major steps include selection of representative structures, consideration of the limit state functions, calculation of reliability for the selected structures, selection of the target reliability index and calculation of load factors and resistance factors. The load and resistance models are reviewed. Statistical models of resistance (load carrying capacity) are summarized for strength limit state in bending, shear and compression. The reliability indices are calculated for several segments of a selected circular tunnel designed according to the tunnel manual report (Tunnel Manual). The novelty of this paper is the selection of the target reliability. In doing so, the uniform spectrum of reliability indices is proposed based on the probability paper. The final recommendation is proposed based on the closeness to the target reliability index.

• International Journal of Highway Engineering
• /
• v.19 no.5
• /
• pp.89-96
• /
• 2017

PURPOSES: This study aims to develop a rational procedure for estimating the pavement roughness index considering vehicle wandering. METHODS : The location analysis of the passing vehicle in the lane was performed by approximately 1.2 million vehicles for verification of the wandering distribution. According to verification result, the distribution follows the normal distribution pattern. The probability density function was estimated using each lane's wandering distribution model. Then the procedure for applying a weighted value into the lane profile was conducted using this function. RESULTS : The modified index, MRIw, with consideration towards applying the wandering weighted value application was computed then compared with MRI. It was found that the Coefficient of Variation for distribution of lateral roughness index in the lane was high in the case of a large difference between each index (i.e., MRIw and MRI) observed. CONCLUSIONS : This result confirms that the new procedure with consideration of the weight factor can successfully improve the lane representative characteristics of the roughness index.