• Geophysics and Geophysical Exploration
• /
• v.7 no.3
• /
• pp.184-190
• /
• 2004

To analyze soil properties of unsaturated zone, we applied electrical resistivity tomography(ERT) of high resolution image. From linear relationship with each soil texture between results of ERT and soil properties such as electrical conductivity of pore water, water contents and ionic contents, we could be analyzed the result of ERT more effectively. Consequently, ERT can be useful for estimating soil properties between the two holes and evaluating indirectly pH and organic contents of soil.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.04b
• /
• pp.47-47
• /
• 2009

The formation of variable one-dimensional structures including core/shell structure is of particular significance with respect to potential applications for thermoelectric devices with the enhanced figure of merit ($ZT=S2{\sigma}T/{\kappa}$). We report the fabrication of Bi-Te core/shell nanowire based on a novel stress induced method. Fig. 1 schematically shows the nanowire fabrication process. Bi nanowires are grown on the Si substrate by the stress-induced method, and then Te is evaporated on the Bi nanowires. Fig. 2 is a transmission electron microscopy image clearly showing a core/shell structure for which effective phonon scattering and quantum confinement effect are expected. Electrical conductivity of the core/shell nanowire was measured at the temperatures from 4K to 300K, respectively. Our results demonstrate that Bi-Te core/shell nanowire can be grown successfully by the stress-induced method. Based on the result of electrical transport measurement and characteristic morphology of rough surface, Seebeck coefficient and thermal conductivity of Bi-Te core/shell nanowires are presented.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.84.2-84.2
• /
• 2011

In this research, two thin film deposition techniques, Atomic Layer Deposition and Sputtering are carried out for the fabrication of Yittria Stabilized Zirconia electrolyte for thin film Solid Oxide Fuel Cell. Zirconium to Yittrium ratio for both cases is about 1/8. Scanning Electron Microscope(SEM) image shows that the growth rate per hour for Atomic Layer Deposition is faster than for sputtering. X-ray Photo-electron Spectroscopy(XPS) shows that the peaks of both Zirconia and Yittria shift towards higher bending energy for the case of Atomic Layer deposition and thus are more strongly attached to the substrate. Later, Nyquist plot was used to compare the conductivity of Yittria Stabilized Electrolyte for both cases. The conductivity at $300^{\circ}C$ for Atomic Layer Deposited Yittria Stabilized Zirconia is found to be $5{\times}10^{-4}S/cm$ while that for sputtered Yittria Stabilized Zirconia is $2{\times}10^{-5}S/cm$ at the same temperature. The reason for better performance for Atomic Layered YSZ is believed to be the Nano-structured layer fabrication that aids in along the plane conduction as compared to the columnarly structured Sputtered YSZ.

• Geophysics and Geophysical Exploration
• /
• v.1 no.3
• /
• pp.155-160
• /
• 1998

EM tomography technique has been developed. The algorithm used the extended Born approximations for forward modeling and reconstructed a conductivity image by a smoothness constraint least squares inversion method. Observed data, the vertical components of secondary magnetic fields, were simulated with the 3-D integral equation code. The results showed that the location of anomalous body could be imaged very well, but conductivity of the body was lower than real one and the vertical resolution was much higher than the horizontal resolution.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.3
• /
• pp.237-241
• /
• 2013

The correlation between NiO-YSZ microstructure and its electrical property used for SOFC anode was critically evaluated with image processing and direct measurement techniques. These innovative processing techniques were employed to quantify the contiguity of the anode constituent phase. The calculated contiguities were then correlated with electrical conductivity attained from 4-probe DC method. This investigation described that contiguity of nickel oxide phases of an anode has a linear relationship with its electrical conductivity. We observed that the contiguity of NiO increased from 0.18 to 0.50 then electrical conductivity attained was significantly increased from 520 S/cm to 1468 S/cm at $900^{\circ}C$.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.8
• /
• pp.82-88
• /
• 2008

This paper describes the influence of the bridge formed between electrodes by electrolyte for tracking process. Electrolytes is made by IEC(International Electrotechnical Commission) 60589, NaCl added to deionized water as each 1, 3, 5[wt%]. The used test equipment is made according to KS(Korean Industrial Standard) C IEC 00112. It is investigated voltage, current, value of resistance and thermal image when bridge formed between electrodes on tracking process. As a result, as conductivity of electrolyte gets bigger as Joule's heat on bridge also gets bigger. But It is not over electrolyte's boiling point due to evaporation heat of electrolyte. However as conductivity of electrolyte gets bigger as the necessary time of dry band gets shorter. So dry band is existed more long time between ahead of droplet to next droplet and discharge chance at dry band gets much. Therefore tracking process gets faster.

• Journal of Environmental Science International
• /
• v.14 no.8
• /
• pp.801-810
• /
• 2005

The phosphor and ITO(Indium Tin Oxide) films for video phone tube (VPT) were simply prepared by the screen printing and thermal transfer methods. The increasing order of thermal firing of acrylic binder for phosphor and ITO was M6003 < M6664 < A/A 1919 < M500l < M670 1 and all mass of binders were perfectly decomposed at lower temperature than $400^{\circ}C.$ After thermal firing of phosphor paste, the residual of binder on the surface of phosphor could not be found by SEM. Aerosil as thickner provides the thixotropy property for phosphor paste but decrease the brightness of phosphor screen as residual after thermal firing. Since the thixotropy of M5001 binder without aerosil was shown and the storage modulus of phosphor paste by increasing the angular frequency was not nearly changed and the decrease of the storage modulus of phosphor paste by increasing the strain was remarkably shown. It was possible to prepare the phosphor paste which was predominant in the plate separation and the reproduction of pattern after the screen printing. Since the addition of dispersing agent to improve the printing process decreases the electrical conductivity and light transmission of ITa film, it could be found to be necessary the development of binder for phosphor paste that decreases the amount of dispersing agent possibly and does not use the aerosil as additive.

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.5
• /
• pp.521-530
• /
• 2017

Improving the microstructure of NiO/YSZ is one of several approaches used to enhance the electrical and mechanical properties of an anode support in Solid Oxide Fuel Cells (SOFCs). The aim of the work reported in this paper was to predict the relationship between these microstructural changes and the resulting properties. To this end, modification of the anode microstructure was carried out using different sizes of Poly (Methyl Methacrylate) (PMMA) beads as a pore former. The electrical conductivity and mechanical strength of these samples were measured using four-probe DC, and three-point bend-test methods, respectively. Thermal etching followed by high resolution SEM imaging was performed for sintered samples to distinguish between the three phases (NiO, YSZ, and pores). Recently developed image analysis techniques were modified and used to calculate the porosity and the contiguity of different phases of the anode support. Image analysis results were verified by comparison with the porosity values determined from mercury porosimetry measurements. Contiguity of the three phases was then compared with data from electrical and mechanical measurements. A linear relationship was obtained between the contiguity data determined from image analysis, and the electrical and mechanical properties found experimentally. Based upon these relationships we can predict the electrical and mechanical properties of SOFC support from the SEM images.

• Korean Journal of Optics and Photonics
• /
• v.28 no.4
• /
• pp.153-157
• /
• 2017

An infrared camera and laser common-path optical system is applied to DIRCM (directional infrared countermeasures), to increase boresighting accuracy and decrease weight. Thermal effects of a laser beam in a common-path optical system are analyzed and evaluated, to predict any degradation in image quality. A laser beam with high energy density is absorbed by and heats the optical components, and then the surface temperature of the optical components increases. The heated optical components of the common-path optical system decrease system transmittance, which can degrade image quality. For analysis, the assumed simulation condition is that the laser is incident for 10 seconds on the mirror (aluminum, silica glass, silicon) and lens (sapphire, zinc selenide, silicon, germanium) materials, and the surface temperature distribution of each material is calculated. The wavelength of the laser beam is $4{\mu}m$ and its output power is 3 W. According to the results of the calculations, the surface temperature of silica glass for the mirror material and sapphire for the lens material is higher than for other materials; the main reason for the temperature increase is the absorption coefficient and thermal conductivity of the material. Consequently, materials for the optical components with high thermal conductivity and low absorption coefficient can reduce the image-quality degradation due to laser-beam thermal effects in an infrared camera and laser common-path optical system.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1777-1779
• /
• 1999

SMM is a dynamic noncontact electric force microscopy that allows simultaneous access to the electrical properties of molecular system such as surface potential, surface charge, dielectric constant and conductivity along with the topography. SNOAM is a new tool for surface imaging which was introduced as one application of AFM. Operated with non-contact forces between the optical fiber and sample as well as equipped with the piezoscanners, the instrument reports on surface topology without damaging or modifying the surface for measuring of optical characteristic in the films. Here we report our recent results of its application to nanoscopic study of domain structures and electrical functionality in organic thin films by SMM. Furthermore, we have illustrated the SNOAM image in obtaining the merocyanine dye films as well as the optical image.