• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.05a
• /
• pp.636-643
• /
• 1995

The accurate determination of the fuel-cladding gap conductance as functions of rod burnup and power level may be a key to the design and safety analysis of a reactor. The incorporation of a sophisticated gap conductance model into nuclear design code for computing thermal hydraulic feedback effect has not been implemented mainly because of computational inefficiency due to complicated behavior of gap conductance. To avoid the time-consuming iteration scheme, simplification of the gap conductance model is done for the current design model. The simplified model considers only the heat conductance contribution to the gap conductance. The simplification is made possible by direct consideration of the gas conductivity depending on the composition of constituent gases in the gap and the fuel-cladding gap size from computer simulation of representative power histories. The simplified gap conductance model is applied to the various fuel power histories and the predicted gap conductances are found to agree well with the results of the design model.

• Journal of Industrial Technology
• /
• v.28 no.B
• /
• pp.117-122
• /
• 2008

This paper presents the conductance model at high frequency of the Ceramic Metal Halide Lamp and the designing method of the electronic ballast with the LCC resonant tank type by using that model. Conductance model is based on a physical phenomenon in the discharge tube of the lamp and model constants of conductance model are obtained by Least Squares Method. After equivalent impedances are determined by the conductance model, The LCC resonance tank is designed by using the equation of the lamp power. Simulation result using PSpice software and experimental results show that the conductance model in this paper is very useful to design the electronic ballast at high frequency for the Ceramic Metal Halide Lamps.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2488-2493
• /
• 2007

A gap conductance is very important factor which can affect nuclear fuel temperature. Especially, in case of an annular fuel, a gap conductance effect can lead an unexpected heat split phenomena which is caused by a large difference of an inner and outer gap conductance. The gap conductance mechanism is very complicated behavior due to the its strong dependency on microscopic factors such as a contact surface roughness, local contact pressure and local temperature. In this paper, for the decision of test temperature and pressure range, a procedure and calculation results of in-reactor fuel temperature and pressure analysis are summarized which can be applied to test equipment design and determination of test matrix. Based upon analysis results, it is concluded that the minimum and maximum test temperature are $300^{\circ}C$ and $530^{\circ}C$ respectively, and the maximum pellet/cladding interfacial contact pressure should be observed up to 45MPa.

• 한국초전도학회:학술대회논문집
• /
• v.14
• /
• pp.97-97
• /
• 2004

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.1 no.1
• /
• pp.52-59
• /
• 1999

Vegetation canopy plays an important role in $CO_2$/$H_2$O exchange between the biosphere and the atmosphere by controlling leaf stomata. In this study, rice (Oryza sativa L.), a staple crop in Asia was investigated to formulate its single leaf model of photosynthesis and stomatal conductance. Photosynthesis and stomatal conductance were measured with a portable infrared gas analyzer system. Other plant and meteorological variables were also measured. To evaluate empirical constants in this biochemical leaf model, nonlinear least squares technique was used. The maximum catalytic activity of enzyme and the maximum rate of electron transport were $ 100\mu$㏖ $m^{-2}$ $s^{-1}$ and $140 \mu$㏖ m$^{-2}$ s$^{-1}$ (@ 35$^{\circ}C$), respectively. The empirical constants, m and b, associated with stomatal conductance model were 9.7 and $0.06 m^{-2}$ $s^{-1}$ , respectively. On a leaf scale, agreements between the modeled and the measured values of photosynthesis and stomatal conductance were on average within 20%, and the simulation of diurnal variation was also satisfactory On a canopy scale, the Simple Biosphere model(SiB2) was tested using the derived parameters. The modeled energy fluxes were compared against the micrometeorologically measured fluxes over a rice canopy. Agreements between the modeled and the measured values of net radiation, sensible heat and latent heat fluxes, and $CO_2$ flux (i.e., net canopy photosynthesis) were on average within 25%.

• Journal of Sensor Science and Technology
• /
• v.29 no.5
• /
• pp.324-327
• /
• 2020

The impact of output conductance (g_o) on the short-circuit current-gain cut-off frequency (f_T) in In_0.8Ga_0.2As high-electron-mobility transistors (HEMTs) on an InP substrate was investigated. An attempted was made to extract the values of f_T in a simplified small-signal model (SSM) of the HEMTs, derive an analytical formula for f_T in terms of the extrinsic model parameters of the simplified SSM, which are related to the intrinsic model parameters of a general SSM, and verify its validity for devices with L_g from 260 to 25 nm. In long-channel devices, the effect of the intrinsic output conductance (g_oi) on f_T was negligible. This was because, from the simplified SSM perspective, three model parameters, such as g_{m_ext}, C_{gs_ext} and C_{gd_ext}, were weakly dependent on g_oi. However, in short-channel devices, g_oi was found to play a significant role in degrading f_T as L_g was scaled down. The increase in g_oi in short-channel devices caused a considerable reduction in g_{m_ext} and an overall increase in the total extrinsic gate capacitance, yielding a decrease in f_T with g_oi. Finally, the results were used to infer how f_T is influenced by g_oi in HEMTs, emphasizing that improving electrostatic integrity is also critical importance to benefit fully from scaling down L_g.

• Korean Journal of Materials Research
• /
• v.3 no.2
• /
• pp.185-192
• /
• 1993

Abstract Electrorheological effect on the dispersive system of polarizable fine powder/dielectric oil has been investigated. ER effect was explained divided into following 3 mechanisms; (1) surface conductance, (2) bulk conductance, and (3) induced polarization. Mathematical model which predicts the interactive force between two fine particles in the electrorheological fluid has been introduced based on the induced polarization mechanism. This model may provide guide to select materials for strong ER effect. The attractive force between two particles was calculated using the above model for the selected 7 materials such as ceramics, ferrites, polymers etc. From the calculation result, it was found that the ceramics and ferrites are good materials which show a strong ER effect.

• Bulletin of the Korean Chemical Society
• /
• v.19 no.12
• /
• pp.1347-1350
• /
• 1998

The equivalent conductances for tetraethylammonium perchlorate (TEAP), tetrabutylammonium perchlorate (TBAP), tetrahexylammonium perchlorate (THAP), and tetradodecylammonium perchlorate (TDDAP) were measured in pyridine (Py) at 25 ℃. The measured data have been analyzed by Onsager conductance theory. From Kohirausch's law of independent migration of ion, the limiting ionic conductances of tetraalkylammonium ions were determined using the limiting ionic conductance of perchlorate cited from reference. Using those and viscosity of pyridine, the Stokes and hydrodynamic radii of tetraethylammonium, tetrabutylammonium, tetrahexylammonium, and tetradodechylammonium ions were calculated. And, the salvation numbers of corresponding ions were also calculated using the hydrodynamic and crystallographic radii and the volume of one pyridine molecule. From those results, the model of salvation for those ions was extracted by comparison with the model for ion salvation. And the electrostatic Gibbs free energy (ΔGel) fitted for our salvation model was calculated. Those of corresponding ions in pyridine at 25 ℃ also increased with increasing radii of tetraalkylammonium ions. This trend of ΔGel was explained by the different ion-solvent interaction between tetraalkylammonium ion and pyridine.

• Nuclear Engineering and Technology
• /
• v.52 no.12
• /
• pp.2760-2770
• /
• 2020

A model for calculation of fuel temperature profile using binary gas mixture of Helium and Xenon for gap gas conductance is proposed here. In this model, the temperature profile of a fuel pencil from fuel centreline to fuel surface has been calculated by taking into account the dilution of Helium gas filled during fuel manufacturing due to accumulation of fission gas Xenon. In this model an explicit calculation of gap gas conductance of binary gas mixture of Helium and Xenon has been carried out. A computer code Fuel Characteristics Calculator (FCCAL) is developed for the model. The phenomena modelled by FCCAL takes into account heat conduction through the fuel pellet, heat transfer from pellet surface to the cladding through the gap gas and heat transfer from cladding to coolant. The binary noble gas mixture model used in FCCAL is an improvement over the parametric model of Lassmann and Pazdera. The results obtained from the code FCCAL is used for fuel temperature calculation in 3-D neutron diffusion solver for the coolant outlet temperature of the core at steady operation at full power. It is found that there is an improvement in calculation time without compromising accuracy with FCCAL.

• Nuclear Engineering and Technology
• /
• v.27 no.3
• /
• pp.344-357
• /
• 1995

The gap conductance between the fuel and the sheath depends strongly on the gap width and has a significant influence on the amount of initial stored energy. The modified Ross and Stoute gap conductance model in ELESTRES is based on a simplified thermal deformation model for steady-state fuel temperature calculations. A review on a series of experiments reveals that fuel pellets crack relocate, and are eccentrically positioned within the sheath rather than solid concentric cylinders. In this paper, the hue recently-proposed gap conductance models (offset gap model and relocated gap model) are described and are applied to calculate the fuel-sheath gap conductances under experimental conditions and normal operating conditions in CANDU reactors. The good agreement between the experimentally-inferred and calculated gap conductance values demonstrates that the modified Ross and Stoute model was implemented correctly in ELESTRES. The predictions of the modified Ross and Stoute model provide conservative values for gap heat transfer and fuel surface temperature compared to the offset gap and relocated gap models for a limiting power envelope.