• 한국지반공학회논문집
• /
• 제34권12호
• /
• pp.133-143
• /
• 2018

수평하중에 대한 말뚝의 휨강도를 증대시키기 위해 얇은 두께의 강관 내부에 PHC말뚝을 합성한 콘크리트 충전 강관(PCFT)말뚝이 개발되었다. PCFT말뚝의 휨강도를 강관말뚝과 비교하기 위하여 직경이 동일한 PCFT말뚝과 강관 말뚝에 대해 휨강도시험을 수행함과 동시에 한계상태설계법으로 P-M 상관도를 작도하였다. 그리고 PCFT말뚝의 하단에 PHC말뚝을 연결한 PCFT 복합말뚝의 수평지지력과 수평거동을 기존의 강관 복합말뚝(HCP) 및 강관말뚝과 비교하기 위하여 총 4본의 시험말뚝을 시공하고 수평재하시험을 수행하였다. 휨강도시험 결과 PCFT말뚝의 휨강도는 두께 12mm의 강관말뚝보다 18.7% 향상되었고, 동일한 휨하중에서 말뚝의 변위량은 강관말뚝보다 50% 감소하였다. 그리고 P-M 상관도로부터 연직하중을 받는 PCFT말뚝은 강관말뚝보다 휨내력이 크게 증가한 반면, 인발하중을 받는 PCFT 말뚝은 강관말뚝보다 휨내력이 감소함을 알 수 있었다. 또한 시험말뚝에 대한 수평재하시험의 결과에 따르면 상부말뚝의 길이가 동일한 경우 PCFT 복합말뚝은 HCP보다 수평지지력이 60.5% 컸고, 두께가 12mm인 강관말뚝보다 35.8% 큰 것으로 나타났다.

• 한국지반공학회논문집
• /
• 제35권9호
• /
• pp.15-28
• /
• 2019

PHC말뚝을 생산하는 17개 중소산업체의 품질 성능 검사 자료, 17개 중소산업체 및 6개 대기업 산업체의 장기허용압축하중 제원 표를 분석하였다. 현 단계의 국내 설계에서는 PHC말뚝의 장기허용압축하중의 평균 약 70% 수준을 반영하고 있고 품질이 우수함에도 불구하고 PHC말뚝의 장기허용압축하중에는 안전율 4.0을 적용하고 있다. 대부분의 품질 검사 기준은 KS F 4306에 명시되어 있다. 그러나 원심력으로 다져진 콘크리트 압축강도시험 기준은 KS F 2454에 명시되어 있다. 각 제조사의 품질 시험 자료를 분석한 결과 모든 항목에서 기준값 보다 높은 성능을 보였다. 따라서 PHC말뚝 설계 시 PHC말뚝의 지지력을 PHC말뚝의 허용연직압축하중의 최대값까지 사용할 수 있을 것으로 판단되었다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 봄 학술발표회 논문집
• /
• pp.249-258
• /
• 1999

Dynamic load and static load tests are performed on steel pipe piles and concrete piles at five construction sites in highway to compare the difference of load bearing mechanisms. At each site, one steel pile is instrumented with electric strain gages and dynamic tests are performed on the pile during installation. Damages of strain gages due to the installation are checked and static test is performed upon the same pile after two or seven days as well. It shows that load transfer from side friction to base resistance behaves somewhat differently according to the results of load-settlement analysis obtained from PDA and static load test. Initial elastic stage of load settlement curves of two load tests is almost similar. But after the yielding point, dynamic resistance of pile behaves more stiffer than static resistance, thus, dynamic load test result might overestimate the real pile capacity compared with static result. Analysis of gage readings shows that unit skin friction increases exponentially with depth. The skin friction is mobilized at the 1∼2m above the pile tip and contributes to the considerable side resistance. Comparison of side and base resistances between the measured value and the calculated value by Meyerhof's bearing capacity equation using SPT N value shows that the calculated base resistance is higher than the measured. Therefore, contribution of side resistance to total capacity shouldn't be ignored or underestimated. Finally, based upon the overall test results, a construction control procedure is suggested.

• Geomechanics and Engineering
• /
• 제7권1호
• /
• pp.37-53
• /
• 2014

A Web-based pile load test (WBPLT) system was developed and implemented in this study. Object-oriented and concept-based software design techniques were adopted to integrate the pile load test database into the system. A total of 673 case histories of pile load test were included in the database. The data consisted of drilled shaft and driven precast concrete pile axial load tests in drained, undrained, and gravel loading conditions as well as pre-analyzed data and back-calculated design parameters. Unified modeling language, a standard software design tool, was utilized to design the WBPLT system architecture with five major concept-based components. These components provide the static structure and dynamic behavior of system message flows in a visualized manner. The open-source Apache Web server is the building block of the WBPLT system, and PHP Web programming language implements the operation of the WBPLT components, particularly the automatic translation of user query into structured query language. A simple search and inexpensive query can be implemented through the Internet browser. The pile load test database is helpful, and data can be easily retrieved and utilized worldwide for research and advanced applications.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 봄 학술논문 발표대회
• /
• pp.387-388
• /
• 2023

PHC pile head cutting is an essential work in pile foundation construction. However, since the work has labor-intensive characteristics, there are problems such as productivity and safety. So in previous study PHC pile one-cutting head cutting automation equipment was developed to solve this problem. However, it has been investigated as a limitation that checking the cutting position of the PHC pile can be challenging in place where a rotary laser leveler cannot irradiate cutting position, as the sensing unit of the developed automated equipment utilizes an optical method. Therefore, the objective of this study is to delvelop a GNSS-based methodology for sensing the cutting position of PHC piles to overcome the limitations of the optical method and to examine its feasibility for field application. If the proposed methodology is applied to the construction site, it is expected that the convenience and productivity of the PHC pile cutting position sensing work will be improved.

• 한국구조물진단유지관리공학회 논문집
• /
• 제20권5호
• /
• pp.109-115
• /
• 2016

최근 구조물의 대형화에 따른 큰 지지력의 말뚝에 대한 수요가 증가하는 추세이다. 이에 따라 기성 PHC말뚝의 경우에도 700~1,200 mm 범위의 대구경 말뚝에 대한 활용이 증가하고 있고 최근 국내 현장에 적용되고 있다. 이 연구에서는 대구경 PHC말뚝의 휨성능을 향상시키기 위해 철근과 콘크리트로 보강하여 합성 PHC말뚝을 제작하였다. 휨강도 평가는 4등분점 제하실험을 통해 변위제어 방법으로 수행되었다. 휨실험을 통해 LICPT 실험체 횡방향 철근의 변형률 분포를 분석한 결과 횡방향 철근의 배근은 전단균열의 진전과 균열폭 제어에 효과적인 것으로 나타났고, 복부전단균열 발생을 억제할 수 있었다. LICPT 실험체는 LICP 실험체 보다 휨강도가 약 1.08배, 중앙부 변위가 약 1.19배 증가하였고, 횡방향 철근의 배근은 말뚝의 연성적인 휨거동 확보에 유리한 것으로 나타났다. 말뚝 제작시 사용되는 각각의 재료가 휨강도에 기여하는 수준을 층상화 단면 해석으로 계산된 축강도-휨모멘트 상관도를 통해 평가하였다. 기성 PHC말뚝과 LICP 실험체의 실제 휨강도를 1.13배, 1.16배의 안전율로 예측할 수 있었다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.869-887
• /
• 2008

Coffer dam for tunnel type spillway in inflow section of Dae-am dam was originally planned as 2 lines sheet piles with Water Zet method. But, the result of pilot test was caused of some problems that vibration during installation of pile could pollute water and water leakage could the lower part. So, sheet piles was not satisfactory for faculty of coffer dam. Structural instability of sheet pile system need to reinforcement. Characteristic of Dae-am dam was small reservoir capacity but wide drainage area, of which it was judgment that security of leakage and stability was difficult during excavation of inlet part. So, we consider that water curtain method utilized with in site pouring concrete pile method was designed at weir part of spillway. We were known about basement rock that geological boring was carried out in weir part. After taking a deep consideration, PRD method was accepted as a new method. Concrete pile by PRD was installed to below country rock. CJM method was carried out with PRD. After making concrete wall using Top-down method, earth anchors were installed for supporting it. According to the result of numerical analysis, as water level rises, wall is stable.

• 한국지반공학회논문집
• /
• 제27권2호
• /
• pp.91-101
• /
• 2011

본 연구에서는 소성힌지를 고려한 단일 현장타설말뚝의 수평거동을 분석하기 위하여 Beam-Column 해석모델을 토대로 단일 현장타설말뚝 기초의 거동특성을 파악하고, 소성힌지를 고려한 최적설계법을 제안하였다. 단일 현장타설말뚝의 소성힌지를 지상부로 유도하기 위한 최적의 기둥-말뚝의 직경비를 분석하기 위해, 변단면 단일 현장타설말뚝의 단면조건에 따른 균열 휨모멘트를 산정하고 지반조건과 수평하중에 따른 말뚝의 거동을 해석하였다. 연구 결과, 최적의 단면 조건은 기둥/말뚝 직경비($D_c/D_p$)와 정규화된 수평균열하중($F/F_{Dc}=D_p$)의 관계를 나타내는 이중직선의 변곡점 이하 부분에서 산정할 수 있었으며, 이로부터 최적의 단면 조건을 제안하였다. 또한 실제 시공사례 분석을 통해, 깊이별 휨모멘트를 바탕으로 최소철근비 적용이 가능한 구간을 분석하였으며, 그 결과 말뚝길이($L_p$)로 정규화된 최소 철근비 적용이 가능한 한계깊이($L_{As=0.4%}$)는 말뚝 직경으로 정규화된 말뚝길이($L_p/D_p$)에 따라 선형적으로 감소하였으며, $L_p/D_p=17.5$ 이후부터는 일정한 값(${\simeq}0.3$)에 수렴함을 알 수 있었다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.553-558
• /
• 2010

The behavior of composite piles composed of steel pipe pile in the upper part and concrete pile in the lower part by a mechanical splicing joint was examined by field lateral load tests and bending tests. A total of 7 piles including two instrumented piles for bending test were installed. The soil profile consists of soft clay with weak silt with shallow groundwater level. Laboratory tests were carried out to determine the basic soil characteristics and the strength parameters. This paper presents the composite pile behavior with various portions of the upper steel pile: 0, 20, 30, and 45% of the pile embedded pile length. Three-point bending tests were performed to investigate the stress-strain relation at the mechanical joint. Based on these test results, the behavior of composite piles with various upper steel pile length are evaluated and the stability of mechanical joints are examined. Through comparisons with results of field load tests, it was found that lateral load carrying capacity of the composite piles increased and deflections of the composite piles decreased with increasing the upper steel piles. The mechanical joint was proved to retain its structural stability against the tested load conditions. Economical benefits of composite pile of this kind can be gained by setting adequately the length of the upper steel pipe piles.

• Computers and Concrete
• /
• 제32권2호
• /
• pp.217-232
• /
• 2023

Numerous studies have been performed on the behavior of pile foundations in cold regions. This study first attempted to employ artificial neural networks (ANN) to predict pile-bearing capacity focusing on pile data recorded primarily on cold regions. As the ANN technique has disadvantages such as finding global minima or slower convergence rates, this study in the second phase deals with the development of an ANN-based predictive model improved with an Elephant herding optimizer (EHO), Dragonfly Algorithm (DA), Genetic Algorithm (GA), and Evolution Strategy (ES) methods for predicting the piles' bearing capacity. The network inputs included the pile geometrical features, pile area (m²), pile length (m), internal friction angle along the pile body and pile tip (Ø°), and effective vertical stress. The MLP model pile's output was the ultimate bearing capacity. A sensitivity analysis was performed to determine the optimum parameters to select the best predictive model. A trial-and-error technique was also used to find the optimum network architecture and the number of hidden nodes. According to the results, there is a good consistency between the pile-bearing DA-MLP-predicted capacities and the measured bearing capacities. Based on the R2 and determination coefficient as 0.90364 and 0.8643 for testing and training datasets, respectively, it is suggested that the DA-MLP model can be effectively implemented with higher reliability, efficiency, and practicability to predict the bearing capacity of piles.