• Polymer(Korea)
• /
• v.26 no.2
• /
• pp.185-192
• /
• 2002

Rigid polyurethane foams (PUFs) were prepared from polymeric 4.4'-diphenyl-methane diisocyanate (PMDI), polyether polyol, 1,4-butane diol, silicone surfactant, and distilled water. The density of the PUF was decreased from 173.7 to 41.7 kg/㎥ with an increase in distilled water from 0.5 to 3.0 php (parts per hundred polyol by weight), respectively, at the 0 php butane diol. The cell size of the PUF increased from 115 to 258 $mu extrm{m}$ with an increase in the amount of distilled water from 0.5 to 3.0 php, respectively, at the 10 php butane diol. It was found that the compressive strength of the PUF increased with the content of distilled water, at the same density. Out of the study for the surfactant effect on the properties of the PUF, it was observed that the cell site of the PUF decreased from 360 to 146 $mu extrm{m}$ with an increase in the amount of the surfactant from 0 to 0.33 php, respectively, but the tell size did not change significantly when the amount of the surfactant exceeded 0.33 php.

• Korean Journal of Materials Research
• /
• v.8 no.11
• /
• pp.993-998
• /
• 1998

In this study TiNi/A16061 shape memory composite is introduced as one of new material using a shape memory alloy. High tensile strength of composite due to compressive residual stress in matrix by the shape memory effect of TiNi fiber can be produced. This composite can remove the tensile residual stress by the difference of coefficients of thermal expansion between fiber and matrix. one of the significant weak point of metal matrix composite. In this paper, shape memory composites are made by squeeze casting. And then, microstructure and fatigue properties of the composites by shape memory effect above inverse transformation temperature A, of TiNi alloy are discussed. The results of the fatigue crack control properties of TiNi/A16061 shape memory composite by a squeeze casting are summarized as follows the effect of fatigue crack propagation control at 363K increases according to the increase of volume fraction and prestrain in composites.

• Resources Recycling
• /
• v.27 no.3
• /
• pp.39-47
• /
• 2018

According to Vietnam government establishes additional coal-fired power plants to secure generation capacity, emission of ashes is accelerating and processing them is urgent issue. This study targeted utilize fly ashes that occurred in circulating fluidized bed combusion (CFBC) power plant to use ground solidification materials. CFBC fly ashes are used to make solidification with ground granulated blast furnace slag (GGBFS), gypsum and cement. Then produced specimens by mixing with soft ground soil to confirm mixing effect of fly ash in solidification. As a result it was possible to find mixture design that is satisfied 3 MPa compressive strength in age 28 days and reduce weight loss rate over 50% in acid immersion test than plain specimens that using only ordinary portland cement.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.6
• /
• pp.26-33
• /
• 2012

This paper reported on the effect of blended activator on the physical properties of alkali-activated slag mortar. Five different activators(caustic alkalis) were used: sodium hydroxide(NaOH, A Case), calsium hydroxide($Ca(OH)_2$, B Case), magnesium hydroxide($Mg(OH)_2$, C Case), aluminum hydroxide($Al(OH)_3$, D Case), and potassium hydroxide(KOH, E Case). We blended five caustic alkalis with sodium carbonate($Na_2CO_3$). The dosage of five caustic alkalis was 3M and sodium carbonate was 1M, 2M and 3M. The result of flow and setting time was decrease as the dosage of sodium carbonate increase. But the compressive strength was increase as the dosage of sodium carbonate increase. It was shown that there is a good effect of blended caustic alkalis with sodium carbonate in alkali-activated slag mortar.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.3
• /
• pp.122-129
• /
• 2016

In this study, we developed a pressing device which can reproduce the pressure of concrete inside the conveying pipe as a part of the basic study to development of high fluidity concrete under high pressure pumping. Using this pressing device, we evaluated a absorption properties of aggregate that are crushed coarse aggregate, river gravel and lightweight coarse aggregate according to pressure of coarse aggregate and aggregate inside a high fluidity concrete, focused on the reduction of unit water quantity by pressure. In addition, it was evaluated the compressive strength of high fluidity concrete about before and after of pressive. Test a result, case of condition under the high pressure of 250 bar, absorption ratio of crushed coarse aggregate and river gravel were not increased above the surface absorption, absorption ratio of lightweight coarse aggregate was increased than the surface absorption.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.1
• /
• pp.76-84
• /
• 2013

In this study, some engineering properties of OPC and GGBFS shotcrete mortars with alkali-free or aluminate accelerator were experimentally examined. As a result, GGBFS mortars with alkali-free accelerator were significantly similar to OPC mortars with same accelerator with respect to both setting time and compressive strength. Comparatively, GGBFS mortars with aluminate accelerator showed a good performance with an increased replacement of GGBFS. Furthermore, when replaced with GGBFS over 50%, the mortars exhibited superior performances of electrical resistivity and chloride ions penetration resistance. Accordingly, it is suggested that GGBFS has a beneficial effect as shotcreting materials in the condition of proper replacement levels.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.3
• /
• pp.90-96
• /
• 2018

In this study, the mechanical and micro-structural change of cement pastes incorporating Stainless-Steel Slag Argon Oxygen Decarburization Slag (STS-A) containing ${\gamma}-C_2S$ as a carbon capture materials were investigated with carbonation curing condition. ${\gamma}-C_2S$ is non-hydraulic, therefore does not react with water. But ${\gamma}-C_2S$ has a reactivity under carbonation curing condition with water. The reaction products fill up the pore in pastes. The microstructure of STS-A blended cement pastes could be densified by this reaction. The pore structure of cement pastes incorporating STS-A was measured using mercury intrusion porosimetry (MIP) after carbonation curing ($CO_2$ concentration is about 5%). Also the fractal characteristics were investigated for the effect of carbonation curing on the micro-structural change of paste specimens. From the results, the compressive strength of carbonated specimens incorporating STS-A increased and pore-structure of carbonated paste is more complicated.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.2
• /
• pp.78-85
• /
• 2020

Shotcrete concrete is generally used in the form of ready-mixed concrete products using type I ordinary portland cement(hereinafter referred to as OPC) and about 5% of accelerator mixed separately in the field. In this study, we tested the effect of OPC fineness and SO₃ content on a penetration resistance, compressive strength of binder for shotcrete using calcium aluminate type accerlerator. And we analysed hydrates and pore structure effects on mortar performance. In the future, it is expected to be useful for manufacturing optimized OPC as a binder for shotcrete.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.2
• /
• pp.86-93
• /
• 2020

Shotcrete concrete is generally used in the form of ready-mixed concrete products using type I ordinary portland cement(hereinafter referred to as OPC) and about 5% of accelerator mixed separately in the field. In this study, we tested the effect of addition of slag powder(SP) and limestone powder(LSP) on a penetration resistance, compressive strength of binder for shotcrete using calcium aluminate type accerlerator. And we analysed hydrates and pore structure effects on mortar performance. In the future, it is expected to be useful for manufacturing optimized composite cement as a binder for shotcrete.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.2 no.2
• /
• pp.166-171
• /
• 2014

This experimental study considers manufacturing method of the non-portland cement matrix for the light-weight building materials using blast furnace slag, paper ash, fly ash and polysilicon sludge the industrial by-product. For the experiment, we used paper ash by means of the foaming agent and alkali activator to make non-portland cement light-weight matrix. Various specimens were prepared with different types and addition ratios of the alkali activator. Then, the properties of these specimens were investigated by compressive strength test, bulk specific gravity. As a results, it was judged that experiment results of non-portland cement matrix with specific waste resources and alkali activators were useful as basic data for mixtures design and evaluation properties of lightweight non-portland cement building material.