• Journal of the Korea Concrete Institute
• /
• v.25 no.6
• /
• pp.675-682
• /
• 2013

In this study, to enhance the quality of concrete surface by removing the surplus water, permeable liner attached the euroform was applied for manufacturing concrete specimens. Various kinds of concrete mixtures with different water to binder ratios were applied and the strength properties of the hardened concrete surfaces were evaluated at different heights. Experimental results showed that the rebound values by schmidt hammer test and the compressive strengths on the surfaces of concrete specimens were increased as proportion to the amount of mixture water which is dependent on the water to binder ratio of each concrete mixture, and more enhancements were observed on the middle and lower specimen surfaces than the upper region. SEM analysis also showed that much denser hydrate structures were observed on the specimen surfaces by the application of the permeable liner while similar hydrate formations were occurred regardless of surface treatment conditions. From the MIP test results of the concrete surfaces, it was observed that, by the application of permeable liner, the pore volume below $0.01{\mu}m$ was decreased with a maximum of 50% resulting in the densification of pore structures.

• Journal of Environmental Health Sciences
• /
• v.8 no.2
• /
• pp.13-31
• /
• 1982

Factors affecting on dewatering characteristics of anaerobically digested or/and elutriated sludges were examined from 15 January 1982 to 30 April 1982, results obtained were as follows 1. Sludges, either anaerobically digested or/and elutriated sludges, which were produced at the Joong Rang Cheon Sewage Treatment Plant wore found to be compressive in its nature, coefficient of compressibility ranged from 0.83 for unelutriated and 1.10 for elutriated. 2. Dosage of FeC13 for the anaerobically digested sludges were difficult to establish for the most favorable dosage rate, though the filterability indicated linear improvement with increased dosage from dosing rate excess of over 15% in terms of dry solids by weight, under the conditions of this examination. Optimum filterability were obtained with 9~11% of $FeCl_3$ for elutriated sludges, and required CaO, as aids, were appeared to be 2.5~3.5 times that of the $FeCl_3$ at that point by weight. 3. The specific resistances for anaerobically digested sludges showed higher value than the elutriated one, being $11 \times 10^{12} ~ 20 \times 10^{12}$ cm/g with no chemical conditioning, and $2 \times 10^{12} ~ 11 \times 10^{12}$ cm/g with conditioned ($FeCl_3$ + CaO) contrast to $0.5 \times 10^{12} ~ 2.0 \times 10cm/g$ for the elutriated. 4. The strength of the alkalinities before and after elutriation were measured to 10,000 ~ 15,000 mg/l and 1,500 ~ 2,000mg/l respectively. These alkalinities affected greatly on the filterabilities together with concentration of the organic matters in the sludges. 5. The yields with 11% $FeCl_3$, by weight to the DS, on the elutriated sludges averaged to $14.7 kg/m^2.hr$, and $3.2kg/m^2.hr$ for unelutriated sludges. Which was 4.6 times of not elutriated sludges. Elutriated sludges without chemical conditioner added showed much better filterabilities than with 15% of $FeCl_3$ added to the anaerobically digested and unelutriated sludges.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.9
• /
• pp.35-44
• /
• 2005

Recently, underground cavities such as limestone cavity and abandoned mine give rise to a lot of damage in SOC facilities. But there are many difficult problems such as delay of the working terms and enormous economic losses in finding a new method and changing construction design. In this study, a new filling material for underground cavities was developed using the stone-dust classified as industry waste polluting environment. As a result of test, filling material properties was that a compressive strength was $34{\~}60\;kgf/cm^2$, a change ratio in length was $0.268{\~}0.776\%$ and water absorption was $34.3{\~}46.9\%$. Also as a result of suspended mass test and pH test, it was confirmed that the developed filling material has a characteristic of non-separating in water and it was an environmentally friendly material.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• v.y2004m10
• /
• pp.71-76
• /
• 2004

This paper investigate that the effect of the concrete containing mineral admixtures(pozzolanic materials such as fly-ash, ground granulated blast-furnace slag, silica fume and meta kaolin) on the resistance properties to chloride ion invasion. The purposed testing procedure was applied to the concrete added mineral admixtures for $3\sim4$ replacement ratios under W/B ratios ranged from 0.40 to 0.55. Specimens were immersed in $3.6\%$ NaCl solution for 330 days, and penetration depth, water soluble chloride contents and acid soluble chloride contents were measured in 28, 91, 182 and 330 days. Then, diffusion coefficient were calculated using total chloride contents. As a results. the kinds of mineral admixture and replacement ratios had a great effect on the resistance property of the concrete to chloride ion invasion compared with the plain concrete. And the optimal replacement ratios of mineral admixture had a limitation for each admixtures. The amount of acid soluble chloride ions and water soluble chloride ions were varied with the kinds of mineral admixtures and the penetration depth from the concrete skin. Chloride diffusion coefficient of each concretes decreased with the time elapsed. and the diffusion coefficients of the concrete immersed salt water for 330 days had a establishment with the compressive strength measured before immersing.

• Journal of the Korean GEO-environmental Society
• /
• v.4 no.2
• /
• pp.47-56
• /
• 2003

The production of industrial wastes have increased due to the growth of population and industrial development. Among these wastes, especially amount of paper ash has been increased year after year. If it is possible to reuse industrial wastes, it will be beneficial not only economically but also environmentally. In this study, the possibility of the utilization of paper ash were investigated as a construction materials through a series of laboratory testing carried out to evaluate physical properties, compaction, consolidation, permeability and compressive strength characteristics. Concrete bricks with replacement ratio of paper ash at 2, 4, 6, 8, 10, 12, 14, 16, 18, 20%, and clayey bricks with replacement ratio of paper ash at 5, 10, 15, 20, 25, 30% were used in the test in order to evaluate its quality. As a result of tests, it were shown that the maximum replacement ratio of paper ash satisfying the quality standards of concrete bricks and clayey bricks were 11.5% and 12%, respectively.

• Journal of the Korean GEO-environmental Society
• /
• v.21 no.11
• /
• pp.11-20
• /
• 2020

For water barrier and reinforcing grout in soft ground, the verification of durability was conducted over the initial and long-term ages under various curing conditions. The grout was made of water glass system, fast-hardening mineral (FHM) system, and acrylic polymer system. There were three types of curing conditions that were tab water curing, artificial seawater curing, and atmospheric curing. And the various tests were performed for each sample by age, uniaxial compressive strength, length change, and weight change. As artificial seawater, MgCl₂ and MgSO₄ aqueous solutions were prepared and used, respectively. As the test results, the fast-hardening mineral system and acrylic polymer system were cured stably without significant change in durability in tap water and artificial sea water, whereas water glass system showed a very rapid drop in durability under artificial sea water conditions compared to tap water. In atmospheric curing conditions, durability is lowered compared to water curing in all cases, and in particular, the weight loss in the FHM system and water glass system is about 62% and 60%, respectively, resulting in a significant decrease in durability.

• Steel and Composite Structures
• /
• v.7 no.6
• /
• pp.457-468
• /
• 2007

Analytical and experimental investigation on dynamic properties of extra lightweight concrete sandwich beams reinforced with various lay ups of carbon reinforced epoxy polymer composites (CFRP) are discussed. The lightweight concrete used in the core of the sandwich beams was made up of extra lightweight aggregate, Lica. The density of concrete was half of that of the ordinary concrete and its compressive strength was about $100Kg/cm^2$. Two extra lightweight unreinforced (control) beams and six extra lightweight sandwich beams with various lay ups of CFRP were clamped in one end and tested under an impact load. The dimension of the beams without considering any reinforcement was 20 cm ${\times}$ 10 cm ${\times}$ 1.4 m. These were selected to ensure that the effect of shear during the bending test would be minimized. Three other beams, made up of ordinary concrete reinforced with steel bars, were tested in the same conditions. For measuring the damping capacity of sandwich beams three methods, Logarithmic Decrement Analysis (LDA), Hilbert Transform Analysis (HTA) and Moving Block Analysis (MBA) were applied. The first two methods are in time domain and the last one is in frequency domain. A comparison between the damping capacity of the beams obtained from all three methods, shows that the damping capacity of the extra lightweight concrete decreases by adding the composite reinforced layers to the upper and lower sides of the beams, and becomes most similar to the damping of the ordinary beams. Also the results show that the stiffness of the extra lightweight concrete beams increases by adding the composite reinforced layer to their both sides and become similar to the ordinary beams.

• Steel and Composite Structures
• /
• v.22 no.1
• /
• pp.63-77
• /
• 2016

Top-down construction is a construction technique in which pit excavation and structure construction are conducted simultaneously. Reducing construction time and minimizing noise and vibration which affect neighboring structures, the technique is widely employed in constructing downtown structures. While H-steel columns have been commonly used as core columns, concrete filled steel tube (CFT) columns are at the center of attention because the latter have less axial directionality and greater cross-sectional efficiency than the former. When compared with circular CFT columns, square CFT columns are more easily connected to the floor structure and the area of percussion rotary drilling (PRD) is smaller. For this reason, square CFT columns are used as core columns of concrete encased and filled square (CET) columns in underground floors. However, studies on the structural behavior and concrete stress transfer of CET columns have not been conducted. Since concrete is cast according to construction sequence, checking the stress of concrete inside the core columns and the stress of covering concrete is essential. This paper presents the results of structural tests and analyses conducted to evaluate the usability and safety of CET columns in top-down construction where CFT columns are used as core columns. Parameters in the tests are loading condition, concrete strength and covering depth. The compressive load capacity and failure behavior of specimens are evaluated. In addition, 2 cases of field application of CET columns in underground floors are analyzed.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.13 no.3
• /
• pp.243-260
• /
• 2011

To predict TBM performance in design stage is indispensable for its successful application. The NTNU model, one of the representative TBM performance prediction models uses two distinct parameters such as DRI and CLI obtained from three different tests on bored rock cores. Based on DRI and CLI, it is possible to predict TBM advance rate and cutter life in the NTNU model. In this study, NTNU testing methods and their related testing equipments were introduced to measure DRl and CLI for the NTNU model. Then, in order to derive their relationships, the two key parameters measured for 39 domestic rocks were compared with physico-mechanical properties of rock such as uniaxial compressive strength and quartz content. Lastly, the experimental results were also compared with NTNU database to verify their reliability.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.3 no.3
• /
• pp.9-21
• /
• 2012

Concrete filled steel tube (CFT) columns have been widely used in moment resisting frame structures both in seismic zones. This paper discusses the design of such members based on the advanced methods introduced in the 2005 AISC Specification and the 2005 Seismic Provisions. This study focuses particularly on design following both linear and nonlinear methods utilizing equivalent static and dynamic loads for low-rise moment frames. The paper begins with an examination of the significance of pseudo-elastic design interaction equations and the plastic ductility demand ratios due to combined axial compressive force and bending moment in CFT members. Based on advanced computational simulations for a series of five-story composite moment frames, this paper then investigates both building performance and new techniques to evaluate building damage during a strong earthquake. It is shown that 2D equivalent static analyses can provide good design approximations to the force distributions in moment frames subjected to large inelastic lateral loads. Dynamic analyses utilizing strong ground motions generally produce higher strength ratios than those from equivalent static analyses, but on more localized basis. In addition, ductility ratios obtained from the nonlinear dynamic analysis are sufficient to detect which CFT columns undergo significant deformations.