• 농업과학연구
• /
• 제23권1호
• /
• pp.51-60
• /
• 1996

This study was performed to evaluate the effects of filler on engineering properties of permeable polymer concrete with unsaturated polyester resin. The following conclusions were drawn; 1. The unit weight was in the range of $1.804{\sim}1.919t/m^3$, the weights of those concrete were decreased 17~22% than that of the normal cement concrete. 2. The highest strength was achieved by stone dust filled permeable polymer concrete, it was increased 17% by compressive, 147% by tensile and 188% by bending strength than that of the normal cement concrete, respectively. 3. The ultrasonic pulse velocity was in the range of 2,722~3,060m/sec, which was showed about the same compared to that of the normal cement concrete. Stone dust filled permeable polymer concrete was showed higher pulse velocity. 4. The water permeability was in the range of $3.076{\sim}4.152{\ell}/cm^2/h$, and it was larglely dependent upon the mix design. These concrete can be used to the structures which need water permeability. 5. The compressive strength, tensile strength, bending strength and ultrasonic pulse velocity were largely showed with the increase of unit weight. But, it was decreased with the increase of water permeability, respectively.

• International Journal of Concrete Structures and Materials
• /
• 제3권1호
• /
• pp.39-45
• /
• 2009

The purpose of this study is to establish flexural behavior of high-strength concrete beams confined in the pure bending zone with stirrups. The experiment was carried out on full-scale high-strength reinforced concrete beams, of which the compressive strengths were 40 MPa and 70 MPa. The beams were confined with rectangular closed stirrups. Test results are reviewed in terms of flexural capacity and ductility. The effect of web reinforcement ratio, longitudinal reinforcement ratio and shear span to beam depth ratio on ductility are investigated. The analytic method is based on finite element method using fiber-section model, which is known to define the behavior of reinforced concrete structures well up to the ultimate state and is proven to be valid by the verification with the experimental results above. It is found that confinement of concrete compressive regions with closed stirrups does not affect the flexural strength but results in a significantly increased ductility. Moreover, the ductility tends to increase as the quantity of stirrups increases by reducing the spacing of stirrups.

• Computers and Concrete
• /
• 제15권4호
• /
• pp.503-514
• /
• 2015

Fibre-added concretes are frequently used in large site applications such as slab and airports as well as in bearing system elements or prefabricated elements. It is very difficult to determine the mechanical properties of the fibre-added concretes by experimental methods in situ. The purpose of this study is to develop an artificial neural network (ANN) model in order to predict the compressive and bending strengths of hybrid fibre-added and non-added concretes. The strengths have been predicted by means of the data that has been obtained from destructive (DT) and non-destructive tests (NDT) on the samples. NDTs are ultrasonic pulse velocity (UPV) and Rebound Hammer Tests (RH). 105 pieces of cylinder samples with a dimension of $150{\times}300mm$, 105 pieces of bending samples with a dimension of $100{\times}100{\times}400mm$ have been manufactured. The first set has been manufactured without fibre addition, the second set with the addition of %0.5 polypropylene and %0.5 steel fibre in terms of volume, and the third set with the addition of %0.5 polypropylene, %1 steel fibre. The water/cement (w/c) ratio of samples parametrically varies between 0.3-0.9. The experimentally measured compressive and bending strengths have been compared with predicted results by use of ANN method.

• Steel and Composite Structures
• /
• 제50권4호
• /
• pp.475-487
• /
• 2024

The usage of fiber-reinforced polymer materials increases in the construction sector due to their advantages in terms of high mechanical strength, lightness, corrosion resistance, low density and high strength/density ratio, low maintenance and painting needs, and high workability. In this study, it is aimed to improve mechanical properties of GFRP box profiles, produced by pultrusion method, by filling the polymer concrete into them. Within the scope of study, hybrid use of polymer concrete produced with GFRP box profiles was investigated. Hybrid pressure and bending specimens were produced by filling polymer concrete (polyester resin manufactured with natural sand and stone chips) into GFRP box profiles having different cross-sections and dimensions. Behavior of the produced hybrid members was investigated under bending and compression tests. Hollow GFRP_xx profiles, polymer-filled hybrid members, and nominative polymeric concrete specimens were tested as well. The behavior of the specimens under pressure and bending tests, and their load bearing capacities, deformations and changes in toughness were observed. According to the test results; It was deduced that hybrid design has many advantages over its component materials as well as superior physical and mechanical properties.

• 한국지반환경공학회 논문집
• /
• 제15권4호
• /
• pp.61-67
• /
• 2014

본 연구에서는 시멘트의 유해성을 극복하기 위하여 시멘트 대신에 친환경 토양안정재를 사용한 식생블록을 제작하여 압축강도 및 휨강도 특성을 규명하였다. 식생블록 제작에 사용된 토양안정재는 천연섬유에서 추출한 단섬유와 석회 등을 주원료로 하며 흙의 전단강도를 증가시켜 블록의 내구성을 향상시키면서 식생을 가능하게 하는 특징을 가지고 있다. 일축압축강도 시험을 위한 공시체는 토양안정재와 화강풍화토를 혼합하여 제작하였으며, 토양안정재는 혼합토의 중량대비 6 %, 12 %, 18 %로 변화시켜 물과 교반하였다. 공시체는 공기 중에서 건조하여 각각 5일, 7일, 14일, 28일간 양생시키고 일축압축강도 시험을 수행하였다. 휨강도 시험은 일축압축강도 시험과 동일한 조건으로 블록을 제작하여 각 단계별 휨강도 시험을 실시하였고 현장 적용성 평가를 위하여 토양안정재의 특성을 고려한 최적함수비를 제안하였다. 또한 식생블록에 대한 투수시험 결과 KS F 4419에서 규정하는 투수성 블록의 품질기준을 만족하는 것으로 나타났다.

• 한국강구조학회 논문집
• /
• 제22권5호
• /
• pp.465-475
• /
• 2010

곡선교량시스템에서 거더는 편심하중이 없어도 교량이 가지는 곡률 자체로 인하여 휨 및 비틀림 거동을 하게 된다. 휨과 비틀림을 동시에 받는 강/콘크리트 합성 박스거더는 St. Venant 비틀림에 의해 콘크리트 바닥판에 발생하는 사인장 응력에 의해 그 극한강도가 제한된다. 합성 박스거더의 극한강도를 얻기 위하여 유한요소해석 패키지 프로그램 ABAQUS을 이용하여 재료 및 기하 비선형성뿐 아니라 콘크리트 균열후 거동 등이 고려된 비선형해석을 수행하였다. 또한 구조해석 이론에 근거한 해석적 방법론으로 합성 박스거더의 휨과 비틀림에 대한 극한강도 상호 작용이 고려된 수식을 유도하여 수치해석 결과와 비교하였다. 휨 거동에 의해 정모멘트 구간 박스거더 상부에 발생하는 종방향 압축응력은 바닥판 콘크리트의 전단강도를 일정부분 향상시켜 결과적으로 전체 박스거더의 비틀림강도가 향상되는 효과가 확인되었다. 유한요소해석 및 구조해석 이론 전개의 결과에 근거하여 강합성 박스거더의 극한강도 상호작용을 예측하는 간편한 형태의 수식이 제안되었다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.756-757
• /
• 2006

P/M enables the economical production of components for many kinds of gears. Functionally, the sub gear requires high tooth accuracy and bending fatigue strength. The whole tooth profile was sized after sintering to satisfy the gear tooth accuracy specification. The part was redesigned to reduce machining requirements. The required bending fatigue strength was achieved through appropriate material choice and induction of compressive residual stress by shotpeening after carburizing. The P/M sub gear replaced a forged steel gear, satisfied performance requirements, expanded the use of P/M applications and provided over 30% cost reduction.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1990년도 봄 학술발표회 논문집
• /
• pp.39-44
• /
• 1990

This experimental study is performed by using artificial lightweight aggregate manufactured in laboratory, and the test results of it are compared with those using foreign materials in respect of design compressive strength, unit weight. The tests on strength characteristics such as bending, splitting tensile strength and on mechanical characteristics including σ-εcurve, elastic modulus, poisson's ratio are performed to provide the fundamental data required for the design. From this study, it is possible to obtain the high-strength concrete having compressive strength of 500 kg/㎠ and unit weight of 1.85-2.0 t/㎥. And also it is recommended that sandlightweight concrete having high specfic strength is more practical for general use.

• 한국건축시공학회지
• /
• 제12권5호
• /
• pp.539-547
• /
• 2012

To manufacture laminated wood with improved mechanical properties by providing uniform adhesiveness, the adhesive was applied and the plate adhesive was laminated on the wood surface. Then, after laminating the wood on the top part of the adhesivebond, it was heated and dried while the adhesive was stiffened using microwaves, and the test piece was manufactured by compressing it with the press machine for thirty minutes. The temperature and the water content were examined according to the heating time of the wood heated with the microwave, and testing was conducted on the shear strength and flexural strength of the wood. In addition, the microstructure of the adhesive bond between the wood was recorded to confirm the penetrabilityinto the wood structure for the adhesive. After the test was conducted, it was found that the test piece manufactured with wood that has its water content leveled with the microwave heating showed improved shear strength and bending strength compared to the standard test piece. With regard to adhesives, liquefied polyvinyl acetate resin and plate's PVB resin were found to have superior adhesive strength. Also, after filming the cellular microstructure, it was found that when the laminated wood is heated with microwaves, the infiltration of the adhesive into the inside of the wood becomes easy, which makes it effective for improving adhesiveness.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 1998년도 학술발표회 발표논문집
• /
• pp.171-175
• /
• 1998

This study was to estimate the strength of pine needle ash concrete using cement, natural aggregates and pine needle ash(PNA). The highest strength was achieved by 5% pine needle ash filled PNA concrete respectively. It was increased 6% by compressive strength, 15% by tensile strength and 13% by bending strength than that of the normal cement concrete, respectively.