• Tunnel and Underground Space
• /
• v.15 no.3 s.56
• /
• pp.223-227
• /
• 2005

The physical and mechanical properties of volcanic glass, which is distributed in the Samho area, South Korea were studied. Laboratory rock tests were carried out in order to obtain the various properties of rocks. Specific gravity, water content, absorption, porosity and wave velocity were measured for the physical properties. Uniaxial and triaxial compressive tests, Brazilian test and point load test were also performed for the mechanical properties. The tests of volcanic glass revealed that the apparent specific gravity, water content and absorption were 2.28, $1.67\%$ and $1.72\%$, respectively. Porosity $(3.87\%)$ was lower, whereas P-wave velocity (5330m/s) and S-wave velocity (2980 m/s) were relatively higher. Brazilian tensile strength ot 7.2MPa, and point load strength of 2.6MPa were among the mechanical properties of the rock. Uniaxial compressive strength (62.4MPa) estimated ken point load strength was very closed to the value (66.0MPa) from the uniaxial compressive test. Young's modulus and Poisson's ratio were E=43.2 GPa and v=0.28, respectively. Drawing the tangent line to Mohr-Coulomb failure criterion showed the cohesion of 20.1MPa and internal fraction angle of $28.6^{\circ}$.

• Korean Journal of Agricultural Science
• /
• v.23 no.1
• /
• pp.61-69
• /
• 1996

This study was performed to evaluate the engineering properties of permeable polymer concrete with fillers and unsaturated polyester resin. The following conclusions were drawn. 1. The highest strength was achieved by stone dust filled permeable polymer concrete, it was increased 17% by compressive, 148% by tensile and 188% by bending strength than that of the normal cement concrete, respectively. 2. The static modulus of elasticity was in the range of $1.17{\times}10^5{\sim}1.32{\times}10^5kg/cm^2$, which was approximately 53~56% of that of the normal cement concrete. Stone dust filled permeable polymer concrete was showed relatively higher elastic modulus. The poisson's number of permeable polymer concrete was less than that of the normal cement concrete. 3. The dynamic modulus of elasticity was in the range of $1.3{\times}10^5{\sim}1.5{\times}10^5kg/cm^2$, which was approximately less compared to that of the normal cement concrete. Stone dust filled permeable polymer concrete was showed higher dynamic modulus. The dynamic modulus of elasticity were increased approximately 10~13% than that of the static modulus. 4. The water permeability was in the range of $3.076{\sim}4.390{\ell}/cm^2/h$, and it was largely dependent upon the mix design. These concrete can be used to the structures which need water permeability. 5. The compressive strength, tensile strength, bending strength and elastic modulus were largely showed with the decrease of water permeability.

• International Journal of Concrete Structures and Materials
• /
• v.10 no.4
• /
• pp.527-537
• /
• 2016

This study evaluated the mechanical characteristics and durability of porous concrete produced with a cementless binder based on ground granulated blast furnace slag (BFS), fly ash (FA) and flue gas desulfurization gypsum (CP). As a result, the void ratio was increased slightly from the target void ratio, by 1.12-1.42 %. Through evaluating the compressive strength, it was found that the compressive strength of porous concrete with cementless binder decreased in comparison to the compressive strength of porous concrete with ordinary Portland cement (OPC), but the difference was insignificant, at 0.6-1.4 MPa. Through the freeze-thawing test to evaluate the durability, it was found that the relative dynamic elastic modulus of porous concrete with cementless binder decreased to 60 % or less at 80 cycles. The result of the chemical resistance test showed that the mass reduction rate was 12.3 % at 5 % HCl solution, and 12.7 % at 12.3 and 5 % $H_2SO_4$ solutions.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.7
• /
• pp.785-792
• /
• 2012

Foam structure is usually hard to model due to the complexity of the geometry of cells. So, many simplified models to represent complicated foam structures have been proposed, but most of them are not actually describe the random feature of the cell structure well. So, in this study, two dimensional isotropic and anisotropic closed cell structures of the foam were modeled using the concept of Voronoi cells. The elasto-plastic deformation behavior under compressive loads was investigated by finitie element analysis, and the results were compared with ideal honeycomb structure. In addition, the effect of anisotropy of Voronoi cell structures of the foam on Young's modulus and yield stress under compressive loads was studied.

• Korean Journal of Materials Research
• /
• v.24 no.2
• /
• pp.111-115
• /
• 2014

Titanium and its alloys are useful for implant materials. In this study, porous Ti-Nb-Zr biomaterials were successfully synthesized by powder metallurgy using a $NH_4HCO_3$ as space holder and $TiH_2$ as foaming agent. Consolidation of powder was accomplished by spark plasma sintering process(SPS) at $850^{\circ}C$ under 30 MPa condition. The effect of high energy milling time on pore size and distribution in Ti-Nb-Zr alloys with space holder($NH_4HCO_3$) was investigated by optical microscope(OM), scanning electron microscope(SEM) & energy dispersive spectroscopy(EDS) and X-ray diffraction(XRD). Microstructure observation revealed that, a lot of pores were uniformly distributed in the Ti-Nb-Zr alloys as size of about $30-100{\mu}m$ using mixed powder and milled powders. In addition, the pore ratio was found to be about 5-20% by image analysis, using an image analyzer(Image Pro Plus). Furthermore, the physical properties of specimens were improved with increasing milling time as results of hardness, relative density, compressive strength and Young's modulus. Particularly Young's modulus of the sintered alloy using 4h milled powder reached 52 GPa which is similar to bone elastic modulus.

• Journal of the Korean Geophysical Society
• /
• v.3 no.2
• /
• pp.127-138
• /
• 2000

This study was conducted to examine the differences between dynamic and static elastic constants by use of some laboratory tests of cement mortar specimens which have different water/cement mixing ratios. Specific gravity measurement, ultrasonic velocity estimating and uniaxial compression test were adopted to acquire the dynamic and static elastic constants. Digital data acquisition and processing enhanced the accuracy of estimating the velocities of specimens drastically, Also, the method using the gradient of propagation delay time in according to increment of specimen length more enhanced the accuracy than the method using the only one specimen length over total propagation time. The correlation between density and the P and S wave velocity of specimens shows reliable positive relation and the correlation between density and the strength of uniaxial compression has the similar relationship. The dynamic Young's modulus $(E_D)$ is alway greater than the static Young's modulus $(E_S)$ and there is increasing tendency of the ratio $(E_D/E_S)$ according to the increase of density or strength of the specimens. On the other hand, there is no typical relationship between dynamic Poisson's ratio $({\nu}_D)$ and static Poisson's ratio $({\nu}_S)$ and just the ratio of ${\nu}_D/{\nu}_S$ ranges front 69 to 122 %.

• Geomechanics and Engineering
• /
• v.22 no.6
• /
• pp.475-488
• /
• 2020

The recent increase in the use of Expanded Polystyrene (EPS) geofoam in construction and geotechnical projects has driven researchers to investigate its behavior, more deeply. In this paper, a series of experimental tests to investigate the stress-strain behavior and the mechanical properties of EPS blocks, under monotonic axial loading are presented. Four different densities of cylindrically shaped EPS with different dimensions are used to investigate the effects of loading rate, height and diameter, as well as the influence of the density of EPS on the stress-strain response. The results show that increasing the height of the EPS samples leads to instability of the sample and consequent lower resistance to the applied pressure. Large EPS samples show higher Young's modulus and compressive resistance due to some boundary effects. An increase in the rate of loading can increase the elastic moduli and compressive resistance of the EPS geofoam samples, which also varies depending on the density of the samples. It was also determined that the elastic modulus of EPS increases with increasing EPS density. By implementing an efficient numerical procedure, the stress-strain response of EPS geofoam samples can be reproduced with great accuracy. The numerical analysis based on the proposed method can used to evaluate the effect of different factors on the behavior of EPS geofoam.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.14 no.1
• /
• pp.102-108
• /
• 2010

The main objective of this study was to evaluate the effect of recycled PET (RPET) fiber made from waste PET bottles to examine application on concrete member. To evaluate the reinforcement effect of RPET fiber in concrete member, experimental tests were performed, such as mechanical property tests (compressive strength, modulus of elasticity and splitting tensile strength) and drying shrinkage test. In mechanical property tests, compressive strength and modulus of elasticity in concrete mixed with RPET fiber gradually decreased, but splitting tensile strength gradually increased as volume fraction of fiber increased. In drying shrinkage test, free drying shrinkage increased. In restrained case, in contrast, crack occurrence was delayed because of tensile resistance increase by RPET fiber. The comparison of RPET and PP fiber added concrete specimen's properties showed that two materials had similar properties. In conclusion, RPET fiber is an alternative material of PP fiber, even finer for its excellence in eco-friendliness due to the recycling of waste PET bottles and its possible contribution to the pollution declination.

• International Journal of Concrete Structures and Materials
• /
• v.4 no.2
• /
• pp.113-118
• /
• 2010

This article aims to study the effects of adding steel fibers to concrete on the mechanical behavior of steel fiber concrete (SFC) slabs. After formulating the SFC, an experimental work was, first, conducted on $160\;{\times}\;320$ mm cylindrical specimens and $70\;{\times}\;70\;{\times}\;280$ mm prisms. Then, this study was carried out on 20 rectangular $1,100\;{\times}\;1,100\;{\times}\;60$ mm small slabs submitted to a distributed load. Two types of fibers with hooked ends were used: long fibers (LF) of a length of 50 mm and short fibers (SF) of a length of 35 mm. The studied parameters are compressive and tensile strengths and Young's modulus. Plain concrete (PC) small slabs were also prepared to be compared to the SFC specimens. The results showed that the compressive strength of SFC increased up to 25% while the splitting tests showed an improvement of the SFC reaching 45%. Tests on SFC small slabs also showed that a smaller deflection is obtained with respect to PC, which indicates an improvement in strength (up to 100%), in ductility and in resistance to cracking. The LF gives a better improvement in strength than the SF for a 70% $kg/m^3$ of steel proportioning.

• Polymer(Korea)
• /
• v.29 no.4
• /
• pp.344-349
• /
• 2005

Polyurethanes(PUs) were synthesized by reaction of isophorone diisocyanate, acetylbutyl citrate, and 3 types of polycaprolactone diol. Their structures were confirmed by FT-IR and NMR spectrometer. And, their thermal and mechanical properties were measured by TGA ud UTM. The effective network chain lengths ($\bar{M}_c$), measured by compressive modulus apparatus, were about $8000\~24000$ g/mol. As crosslinking density and amount of hard segment increased, tensile strength increased and elongation decreased. As the crosslinking density of PUs increased, thermal property inproved. When the ratio of NCO/OH is 1.1, maximum crosslinking density was achieved.