• Steel and Composite Structures
• /
• 제22권6호
• /
• pp.1465-1486
• /
• 2016

Conventional plate I-girders are sensitive to local buckling of the web when they are subjected mainly to shear action because the slenderness of the web in out-of-plane direction is much bigger. The local buckling of the web can also cause the distorsion of the plate flange under compression as a thin-walled plate has very low torsional stiffness due to its open section. A new I-girder consisted of corrugated web, a concrete-filled rectangular tubular flange under compression and a plate flange under tension is presented to improve its resistance to local buckling of the web and distorsion of the flat plate flange under compression. Experimental tests on a conventional plate I-girder and a new presented I-girder are conducted to study the failure process and the failure mechanisms of the two specimens. Strain developments at some critical positions, load-lateral displacement curves, and load-deflection curves of the two specimens have all be measured and analyzed. Based on these results, the failure mechanisms of the two kinds of I-girders are discussed.

• 대한토목학회논문집
• /
• 제28권4A호
• /
• pp.457-463
• /
• 2008

종방향 보강재는 압축플랜지를 단순지지함으로써 국부좌굴강도를 증가시키는 역할을 수행한다. 최근 연구에 의하면, 종방향으로 적절한 간격을 두고 점지지 되었을 경우 그 선을 따라서 단순 지지된 경우와 동일한 좌굴강도를 보이는 것으로 밝혀졌다. 이 같은 연구결과로부터, 하부콘크리트에 부착된 전단연결재가 압축플랜지의 좌굴시 점지지 조건을 만족할 수 있다면 전단연결재가 단순지지의 역할도 수행할 수 있을 것이라는 예측이 가능하다. 이와 같은 사실이 입증이 된다면, 강박스거더 제작비에서 매우 큰 부분을 차지하는 종방향보강재를 생략할 수 있기 때문에 보다 경제적인 설계가 가능해 질 것이다. 본 연구에서는 하부압축플랜지에 종방향보강재를 대체할 전단연결재의 종방향 배치 시 최소간격 결정과 동시에 하부 콘크리트와 합성거동을 하기 위해 소요되는 전단연결재 소요 개수와 간격을 결정하기 위한 연구를 수행하였다.

• Steel and Composite Structures
• /
• 제23권3호
• /
• pp.331-338
• /
• 2017

Cold-formed lipped channel columns (CFLCCs) have been widely used in light gauge steel constructions. The distortional buckling is one of the important buckling modes for CFLCCs and the distortional buckling critical load depends significantly on the rotational restrain stiffness generated by the web to the lipped flange. First, a simplified explicit expression for the rotational restraint stiffness of the lipped flange has been derived. Using the expression, the characteristics of the rotational restraint stiffness of the lipped flange have been investigated. The results show that there is a linear coupling relationship between the applied forces and the rotational restraint stiffness of the lipped flange. Based on the explicit expression of the rotational restraint stiffness of the lipped flange, a simplified analytical formula has been derived which can determine the elastic distortional buckling critical stress of the CFLCCs subjected to axial compression. The simplified analytical formula developed in this study has been shown to be accurate through the comparisons with results from the distortional buckling analyses using the ANSYS finite element software. The developed analytical formula is easy to apply, and can be used directly in practical design and incorporated into future design codes and guidelines.

• 한국강구조학회 논문집
• /
• 제29권4호
• /
• pp.281-289
• /
• 2017

현재의 AASHTO LRFD 및 Eurocode 3 기준은 수평보강 플레이트거더의 휨강도를 과소 평가하는 것으로 나타났다. 이는 웨브보강으로 인한 웨브-플랜지 상호작용을 적절히 고려치 않는 것에 그 원인이 있다. 즉, 웨브 보강 시 압축플랜지의 회전을 구속하는 효과가 증가하여 압축플랜지의 좌굴강도가 증가한다. 또한 압축플랜지와 수평보강재가 웨브의 회전을 구속함으로써 웨브의 일정 영역이 항복강도에 도달하게 된다. 본 연구에서는 수평보강재로 1단 보강된 플레이트 거더에 대해 압축플랜지의 좌굴강도 증가와 웨브의 실제 응력분포를 고려하여 휨강도를 합리적으로 평가하기 위한 모델을 제안하였다. 일반강(SM490) 및 고강도강(HSB800) 플레이트거더에 대해 비선형해석으로부터 휨강도를 평가하고 본 제안 모델의 적용성을 분석하였다.

• Steel and Composite Structures
• /
• 제44권6호
• /
• pp.883-898
• /
• 2022

A hollow-core partially-encased composite beam, named HPEC beam, is investigated in this paper. HPEC beam comprises I-beam, longitudinal reinforcement, stirrup, foam formwork, and cementitious grout. The foam formwork is located on both sides of the web, and cementitious grout is cast within the steel flange. To investigate the shear performance of HPEC beams, static loading tests of six HPEC beams and three control beams were conducted. The shear span ratio and the number of studs on the shear behavior of the HPECspecimens were studied. The failure mechanism was studied by analyzing the curves of shear force versus both deflection and strain. Based on the shear span ratio (𝜆), two typical shear failure modes were observed: shear compression failure when 1.6 ≤ 𝜆 ≤ 2; and diagonal compression failure when 𝜆 ≤ 1.15. Shear studs welded on the flange can significantly increase the shear capacity and integrity of HPEC beams. Flange welded shear studs are suggested. Based on the deformation coordination theory and superposition method, combined with the simplified modified compression field model and the Truss-arch model, Modified Deformation Coordination Truss-arch (M.D.C.T.) model was proposed. Compared with the shear capacity from YB9038-2006 and JGJ138-2016, the calculation results from M.D.C.T. model could provide reasonable predictions.

• 동력기계공학회지
• /
• 제21권1호
• /
• pp.57-62
• /
• 2017

The flexible joint with bellows and flange is made by welding bellows and flange in general. The welded parts cause a crack or demage in the flexible joint due to continuous vibration and fatigue limit. This paper is concerned with development of flexible joint with non-welded, free rotation of flange and non-packing to improve fatigue failure condition between bellows and flange. The support box and support plate that are components of press part are designed to compress fore-end of bellows only without demage of bellows. The production system of flexible joint is designed with piston attached on the compression side. The simulation is performed using Deform 3D software. As the result of simulation, the shape of compressed bellows was most proper in the compression power of $157kg{\cdot}f$ and any deformation has not occurred at a part besides fore-end. The result show that the production possibility of the designed flexible joint.

• Steel and Composite Structures
• /
• 제45권1호
• /
• pp.51-66
• /
• 2022

This paper presents the axial compression behavior of partially encased composite (PEC) columns using H-shaped structural steel. In the experimental program, a total of eight PEC columns with H-shaped steel sections of different flange and web slenderness ratios were tested to investigate the interactive mechanism between steel and concrete. The test results showed that the PEC columns could sustain the load well beyond the peak load provided that the flange slenderness ratio was not greater than five. In addition, the previous analytical model was extended to predict the axial load-strain relationships of the PEC columns with H-shaped steel sections. A good agreement between the predicted load-strain relationships and test data was observed. Using the analytical model, the effects of compressive strength of concrete (21 to 69 MPa), yield strength of steel (245 to 525 MPa), slenderness ratio of flange (4 to 10), and slenderness ratio of web (10 to 25) on the interactive mechanism (K_h = confinement factor for highly confined concrete and K_w = reduction factor for steel web) and ductility index (DI = ratio between strain at peak load and strain at proportional load) were assessed. The numerical results showed that the slenderness of steel flange and yield strength of steel significantly influenced the compression behavior of the PEC columns.

• Structural Engineering and Mechanics
• /
• 제29권6호
• /
• pp.623-642
• /
• 2008

While spatial plastic mechanism analysis has been widely and successfully applied to thinwalled steel structures to analyse the post-failure behaviour of sections and connections, there remains some contention in the literature as to the basic capacity of an inclined yield line. The simple inclined hinge commonly forms as part of the more complex spatial mechanism, which may involve a number of hinges perpendicular or inclined to the direction of thrust. In this paper some of the existing theories are compared with single inclined yield lines that form in flange outstands, by comparing the theories with plate tests of plates simply supported on three sides with the remaining (longitudinal) edge free. The existing mechanism theories do not account for different in-plane displacement gradients of the loaded edge, nor the slenderness of the plates, and produce conservative results. A modified theory is presented whereby uniform and non-uniform in-plane displacements of the loaded edge of the flange, and the slenderness of the flange, are accounted for. The modified theory is shown to compare well with the plate test data, and its application to flanges that are components of sections in compression and/or bending is presented.

• 한국강구조학회 논문집
• /
• 제19권6호
• /
• pp.737-749
• /
• 2007

LRFD 법을 이용하여 3경간 연속 이중합성 박스거더교의 부모멘트를 받는 내측 교각 위 단면을 설계하였다. 3경간 연속교의 최대경간은 80-120m를 고려하였으며 경간비는 1:1.25:1로 가정하였다. 설계 시에는 최대부모멘트를 받는 이중합성거더 단면의 강도한계상태, 사용성한계상태 및 시공성 검토를 고려하였다. 하부 보강콘크리트가 압축플랜지에 합성되기 전에는 압축플랜지의 좌굴을 검토하였으며 합성 후에는 좌굴이 방지된 것으로 가정하였다. 이중합성 박스거더의 하부플랜지 위에 타설하는 콘크리트의 두께에 따른 단면전체의 휨강성과 휨저항강도를 비롯하여 인장플랜지, 압축플랜지 및 복부판의 휨강도를 비교 분석하였다. 상부플랜지와 하부플랜지 단면적비가 이중합성 박스거더의 연성거동 및 휨응력 분포에 미치는 영향을 검토하고 적절한 단면적비를 분석하였다. 하부 보강콘크리트의 유무에 따른 소요 강재량을 비교한 결과, 이중합성 거더의 경우가 기존 단일합성 거더에 비해 15% 내외의 강재량 절감효과가 있는 것으로 분석되었다.

• 소성∙가공
• /
• 제12권2호
• /
• pp.110-115
• /
• 2003

This paper is concerned with the compression test and forming process of flange by using virtual reality and analysis(simulation) program. This virtual manufacturing can be carried out one personal computer without any expensive devices for experiment. The virtual manufacturing composed of three modules such as the imput, calculation and the output modules on internet. Internet user can give the material's property and process parameters to the sever computer at the input module. On the calculation module, a simulator computes the virtual manufacturing process by analysis program and stores the data as a file. The output module is the program in which internet user can confirm virtual manufacturing results by showing tables, graphs, and 3D animation. This programs is designed by an internet language such as HTML, CGI, VRML and JAVA ,while analysis programs use the finite increasing, the virtual manufacturing technique will substitute many real experiments in the future.