• Journal of the Korea Institute of Military Science and Technology
• /
• v.2 no.1
• /
• pp.101-109
• /
• 1999

The objective of this research is to study effects of the residual stresses on the crack growth and the life of the structure, caused by cold working around the hole of the aircraft structure which will be jointed by rivets and bolts, etc. The compensated Morrow's equation, by experimental data from the materials AL7075-T6 and AL2024-T3, is suggested to calculate the values of the fatigue life prediction of the structure. Also, the compensated Forman's equation, by experimental data from a material AL7075-T6, is suggested to calculate the values of the crack growth prediction of the structure. It is founded that the calculated values from the suggested equations are almost close to the known values of the fatigue life prediction and the crack growth prediction. It is shown that this paper, associated with an initial research on the effects of residual stresses around hole, gives a direction to study the problem at the aircraft maintenance field.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.06a
• /
• pp.528-531
• /
• 2007

This paper presents development of a 4-inch WVCA OCB (Optical Compensated Bend)-mode display panel. The developed panel has a built-in circuit of the LTPS (low temperature poly-Si)-integrated gate driver circuit with the function of black data insertion. The function of black data insertion makes it possible to realize rapid response time of 4ms and wide viewing angle of $160^{\circ}$. We also applied the RGBW pixel structure for the brighter image with relatively low power consumption. The developed panel showed improved optical efficiency and driving capability of stable image quality for OCB mode. We developed high efficiency OCB-mode panel with built-in integrated gate driver circuit using LTPS on panel without any external driver IC.

• Journal of Advanced Navigation Technology
• /
• v.20 no.1
• /
• pp.29-36
• /
• 2016

Accuracy of GPS (global positioning system) deteriorates dramatically or positioning is impossible in urban area occasionally since high-rise buildings and elevated roads make the reception of navigation signal very difficult so that number of visible satellites decreases. In these cases, vertical error usually becomes much larger than the horizontal error due to the intrinsic geometry of GPS satellites. To obtain more accurate and reliable height information, this paper proposes a hybrid method that combines GPS and a low-cost barometric altimeter. In the proposed method, the sea-level pressure and the sea-surface temperature are applied to the output of the altimeter. Next, the difference between the ellipsoid and the geoid is compensated. Finally, a simple Kalman filter combines the compensated barometric altitude and the GPS height. By static and car experiments, performance of the proposed method is evaluated. By the experiment results, it can be seen that the proposed method improves the altitude accuracy considerably.

• Journal of Astronomy and Space Sciences
• /
• v.24 no.3
• /
• pp.235-248
• /
• 2007

We developed a software for simulations and analyses of the Image Navigation and Registration (INR) system, and compares the characteristics of Image Motion Compensation (IMC) algorithms for the INR system. According to the orbit errors and attitude errors, the capabilities of the image distortions are analyzed. The distortions of images can be compensated by GOES IMC algorithm and Modified IMC (MIMC) algorithm. The capabilities of each IMC algorithm are confirmed based on compensated images. The MIMC yields better results than GOES IMC although both the algorithms well compensate distorted images. The results of this research can be used as valuable asset to design of INR system for the Communication, Ocean, Meteorological Satellite (COMS).

• Korean Journal of Optics and Photonics
• /
• v.19 no.2
• /
• pp.132-139
• /
• 2008

In scanning laser optical tweezers, high speed scanning stages are used to manipulate a laser beam spot. Due to the inertia of the stage, the output scanning signal decreases with increased frequency of the input signal. This discrepancy in the signals is difficult to observe since most of the energy from the laser beam is blocked out to avoid CCD damage. In this paper, we propose two methods to alleviate these problems. Firstly, frequency responses of piezo stages are measured to analyze the signal drops and the input signal is compensated accordingly. Secondly, an overlay of the scanning path is drawn on the live monitoring screen to enhance the visibility of the scanning path. The result is a drop-compensated scanning with clear path view.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.502-505
• /
• 2005

Researches about micro technology travel lively in these days. Such many researches are concentrated in the field of materials and a process field. But properties of micro materials should be known to give results of research developed into still more. In these various material properties, mechanical property such as tensile strength, elastic modulus, etc is the basic property. To measure mechanical properties in micro or nano scale, actuating must be very precise. PZT is a famous actuator which becomes a lot of use to measure very precise mechanical properties in micro research field. But PZT has a nonlinearity which is called as hysteresis. Not precision result is caused because of this hysteresis property in PZT actuator. Therefore feedback control method is used in many researches to prevent this hysteresis of PZT actuator. Feedback control method produce a good result in processing view, but cause a loss in a resolution view. In this paper, hysteresis is compensated by open loop control method. Hysteresis property is modeled in Mathematical function and compensated control input is constructed using inverse function of original data. Reliability of this control method can be confirmed by testing nickel thin film that is used in MEMS material broadly.

• The Journal of Korean Academy of Prosthodontics
• /
• v.32 no.2
• /
• pp.296-326
• /
• 1994

The purpose of this study was to evaluate the mechanical effects when one implant fixture was connected to the natural teeth with reduced alveolar bone height. This study also examined the effects of increasing the number of abutment teeth and the effects of the intramobile connector and the titanium connector as they were inserted between the implant superstructure and the fixture. The distribution and concentration load was applied to the fixed partial denture(FPD) supported by implant and the natural teeth with reduced alveolar bone height. The stress and displacement of each element was observed and compared by the two-dimensional finite element method. The following results were obtained : 1. The greater the loss of alveolar bone in natural teeth area, the greater the displacement of FPD and the stress concentration in alveolar bone around implant, especially at the stress concentration in the mesial alveolar bone crest around implant fixture. 2. The displacement of FPD was increased more and that of implants fixture was decreased more when intramobile connector was used than titanium connector was used. Also the stress concentration in alveolar bone around implant fixture was greater when intramobile connector than titanium connector. One implication of this finding was that the difference in stiffness of implant and the natural teeth with reduced alveolar bone height could be partially compensated in case of the POM intramobile connector. 3. The amount and direction of displacement and the stress distribution of the 4-unit FPD was better than those of the 3-unit FPD. It implied that the difference of stiffness of implant and natural teeth with reduced alveolar bone height could be partially compensated in case of the 4 unit FPD.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.8 s.350
• /
• pp.6-12
• /
• 2006

Recently, according to the rapid development of mobile system, the development of relative mobile components has been required, and especially, with the miniaturization of mobile component, the complex with nearby components has been progressed. In this paper, multi-output VC-TCXO (Voltage Controlled-Temperature Compensated Crystal Oscillator) for WCDMA integrates the additional CMOS inverter, so it can be the normal clipped sinewave output and additional CMOS output, and also it can be satisfied the VC-TCXO's requirements for WCDMA system. And the important characteristics of reference oscillator, like phase noise and frequency short term stability, are satisfied with WCDMA(UMTS) system's requirement In this paper, however, 25MHz is used for reference frequency, similarly and practically, we think that it can be used from 10MHz to 40MHz.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.39 no.4
• /
• pp.418-428
• /
• 2002

In this paper, we propose a motion-adaptive de-interlacing method using motion compensated interpolation. In a conventional motion compensated method, a simple pre-filter such as line averaging is applied to interpolate missing lines before the motion estimation. However, this method causes interpolation error because of inaccurate motion estimation and compensation. In the proposed method, EBMF(Edge Based Median Filter) as a pre-filter is applied, and new matching method, which uses two same-parity fields and opposite-parity field as references, is proposed. For further improvement, motion correction filter is proposed to reduce the interpolation error caused by incorrect motion. Simulation results show that the proposed method provides better performance than existing methods.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.1
• /
• pp.197-204
• /
• 2010

This paper proposes a new body-effect compensated switch configuration for low voltage and low distortion switched-capacitor (SC) applications. The proposed circuit allows rail-to-rail switching operation for low voltage SC circuits and has better total harmonic distortion than the conventional bootstrapped circuit by 19 dB. A 2-1 cascaded sigma-delta modulator is provided for performing the high-resolution analog-to-digital conversion on audio codec in a communication transceiver. An experimental prototype for a single-stage folded-cascode operational amplifier (opamp) and a 2-1 cascaded sigma-delta modulator has been implemented m a 0.25 micron double-poly, triple-metal standard CMOS process with 2.7 V of supply voltage. The 1% settling time of the opamp is measured to be 560 ns with load capacitance of 16 pF. The experimental testing of the sigma-delta modulator with bit-stream inspection and analog spectrum analyzing plot is performed. The die size is $1.9{\times}1.5\;mm$.