• Journal of the Korean Solar Energy Society
• /
• v.33 no.3
• /
• pp.114-123
• /
• 2013

In these days, most of the office buildings are being required to save energy for maintenance. lighting system constitutes 20% to 30% of the total annual electrical energy consumption in office buildings. As an energy saving strategy for lighting system, dimming control system based on illuminance sensors came into use. But the system is accompanied with many illuminance sensors to control lighting and needs a lot of initial investment. In this study, the prediction equation for indoor daylighting illuminance distribution is proposed through the review for conventional research results and field measurements. The proposed equation was verified by the comparison between predicted results and field measurement results. The developed prediction equation for daylighting can be used to control the indoor illuminance level with the limited sensor when dimming control system is operated.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.48 no.3
• /
• pp.73-82
• /
• 2006

Wind energy is one of the promising renewable energies that could provide electricity and other mechanical power. Wind energy market is dramatically growing in many European countries, but wind power is only 0.2% of the total renewable energy uses that is only about 2% of the primary energy consumption in Korea. It is widely accepted that wind resources fur power generation are only limited in some areas including coastal regions and mountainous areas in Gangwon province in Korea, particularly in terms of large scale wind power developments. In this study, wind velocity data were analyzed with respect to the potential utilization. The data provided from National Weather Service were used for the analysis. In addition, field wind data were also collected and analyzed for the comparison between the national data. The comparison showed that there were significant differences between the experimental station and the national station that are about 5km away. Annual average wind speed at the experimental station was less than 2 m/s, which is not enough fur wind power generation. It seemed that the topographic condition resulted in a significant difference in wind speed. When 600 W and 2.5 kW wind turbines were used, annual power productions were only 186 kWh and 598 kWh, respectively. When the average wind speed is lower, wind pumping is an alternative use of wind. At the experimental station, the average pumping rate of $3m^3/h$ at the head of 3 m was expected at a 2.5 m rotor under the conditions that efficiencies of the rotor and the pump were 40% and 80%, respectively. It did not seem that the wind pumping was not applicable at the station either. A higher wind speed was required to install the wind machines. Meanwhile, wind pumping would be applicable in conditions with lower pumping heads. Other applications were introduced far further wind energy utilization, including wind powered ventilation and friction heat generation in greenhouses.

• Advances in Energy Research
• /
• v.7 no.2
• /
• pp.147-166
• /
• 2020

Industrial cooling towers are often ageing infrastructure that is expensive to maintain and operate. A novel approach is introduced in which a heat pump circuit is incorporated to reduce the load upon the towers by extracting low-grade energy from the stream sent to the towers and repurposing in on-site processing operations. To demonstrate the concept, a model was constructed, which uses industrial data on cooling towers linked to a smelter's sulphuric acid plant, to allow direct economic and environmental impact comparison between different heat recovery and repurposing scenarios. The model's results showed that implementing a heat pump system would significantly decrease annual operating costs and achieve a payback period of 3 years. In addition, overall CO₂ emissions could be reduced by 42% (430,000 kg/year) and a 5% heat load reduction on the cooling towers achieved. The concept is significant as the outcomes introduce a new way for energy intensive industrial sectors, such as mineral processing, to reduce energy consumption and improve long-term sustainable performance.

• Korean Journal of Community Nutrition
• /
• v.27 no.1
• /
• pp.36-46
• /
• 2022

Objectives: The purpose of this study was to evaluate the consumption pattern of sugar-sweetened beverages (SSB) and compare body composition changes by SSB consumption based on 28 days of dietary records from a four-week time-restricted eating intervention among young adults in Korea. Methods: A total of 33 participants completed the four-week dietary intervention with 8-hour time-restricted eating (TRE). The body composition was measured by bioelectrical impedance analysis at baseline, and daily dietary records were collected for 28 days during the intervention after 4 weeks. Results: Based on 924 days of dietary records, the average eating occasion of SSB was 0.9 times per day, and the average amount of SSB was 205.8 g/times. Based on an individual's usual intake of 28 days, the average eating frequency of SSB was 16.6 times out of 28 days, and the average amount of SSB was 184.0 g/day. The average energy intake from SSB was 131.0 kcal /day (8.7% of energy), and sugar intake from SSB was 18.2 g/day (4.9% of energy). The sugar intake was 2.6% of energy from sweetened dairy products, followed by 2.0% from coffee drinks, 0.5% from soda and juice and 0.2% from others. When subjects were divided into high (14 days or more) and low (less than 14 days) SSB groups based on eating frequency, the weight change in the low SSB group was -2.0 kg over 4 weeks, which was significantly lower than -0.7 kg in the high SSB group. However, no significant difference was found in muscle mass, fat mass and body fat percent between the two groups. Conclusions: This study suggests that low consumption of sugar-sweetened beverages is more desirable in weight management despite having the dietary intervention of time-restricted eating without counting calories. Thus, further longitudinal studies on the association between SSB and obesity in Korean adults are necessary.

• Journal of Biosystems Engineering
• /
• v.42 no.2
• /
• pp.112-116
• /
• 2017

Purpose: The purpose of this study was to analyze the milling characteristics of white rice depending on the guide angles of the cutting roller's induced guide, as well as to verify optimum milling conditions for the cutting-type milling machine. Methods: Brown rice, which was produced in Cheongju-si, Chungcheongbuk-do, Republic of Korea, in 2014, was used as the experimental material. The milling characteristics of white rice were measured under six different guide angle levels of the cutting roller, which were none, $0^{\circ}$, $5^{\circ}$, $10^{\circ}$, $15^{\circ}$, and $20^{\circ}$. The quantity of brown rice for each experiment was 500 kg, and the milling characteristics were measured according to the whiteness, rice temperature, cracked rice ratio, broken rice ratio, and energy consumption. Results: The whiteness of white rice maintained a uniform level, indicating at range of $38{\pm}0.5$, regardless of the cutting roller guide angles under all conditions. The rice temperature rise during milling was found to be rather low, at $13.9^{\circ}C$ and $13.6^{\circ}C$ at $10^{\circ}$ and $15^{\circ}$ guide angles, respectively. The cracked rice ratio after milling was 18.67%-19.47%, and the broken rice ratio was 0.68% at a $10^{\circ}$ guide angle, which is the lowest in comparison to other guide angles. Energy consumption was lower when the guide was used compared to that with-out the use of the guide. The energy consumption tended to increase as the cutting roller guide angle increased. Conclusions: From the above results, we conclude that the cutting roller guide angles of $0^{\circ}$ and $10^{\circ}$ are suitable for producing high quality rice during milling with a cutting-type milling machine.

• Journal of Microbiology and Biotechnology
• /
• v.14 no.6
• /
• pp.1120-1128
• /
• 2004

The SCBFC was composed of bilayered cathode, the outside of which was modified with $Fe^{3+}$ (graphite-Fe(III) cathode) and the inside of which was porcelain membrane, and of an anode which was modified with $Mn^{4+}$ (graphite­Mn(lV) anode). The graphite-Fe(III), graphite-Mn(IV), and porcelain membrane were designed to have micropores. The outside of the cathode was exposed to the atmosphere and the inside was contacted with porcelain membrane. In all SCBFCS the graphite-Fe(III) was used as a cathode, and graphite-Mn(IV) and normal graphite were used as anodes, for comparison of the function between normal graphite and graphite-Mn(IV) anode. The potential difference between graphite-Mn(IV) anode and graphite-Fe(III) cathode was about 0.3 volt, which is the source for the electron driving force from anode to cathode. In chemical fuel cells composed of the graphite-Mn(IV) anode and graphite-Fe(III) cathode, a current of maximal 13 mA was produced coupled to oxidation of NADH to $NAD^{+}$ the current was not produced in SCBFC with normal graphite anode. When growing and resting cells of E. coli were applied to the SCBFC with graphite-Mn(IV) anode, the electricity production and substrate consumption were 6 to 7 times higher than in the SCBFC with normal graphite anode, and when we applied anaerobic sewage sludge to SCBFC with graphite-Mn(IV) anode, the electricity production and substrate consumption were 3 to 5 times higher than in the SCBFC with normal graphite anode. These results suggest that useful electric energy might possibly be produced from SCBFC without electron mediators, electrode-active bacteria, and extra energy consumption for the aeration of catholyte, but with wastewater as a fuel.

• Proceedings of the KIEE Conference
• /
• 1999.11b
• /
• pp.172-174
• /
• 1999

In Korea, the consumption of renewable energy among primary energies has marked only 1.03%, composed of mostly hydro power facilities, as of 1998. This situation has been basically due to the market limit and high generation cost of renewable energies. Furthermore, the policies and strategies for promoting the renewable energy have been insufficient in comparison with that of the developed countries. This paper mainly focuses on the economic feasibility and sensitivity analysis for renewable energies.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.3 no.2
• /
• pp.141-149
• /
• 2011

The world is facing a challenge in meeting its needs for energy. Global energy consumption in the last halfcentury has increased very rapidly and is expected to continue to grow over the next 50 years. However, it is expected to see significant differences between the last 50 years and the next. This paper aims at introducing a good solution to replace or work with conventional marine power plants. This includes the use of fuel cell power plant operated with hydrogen produced through water electrolysis or hydrogen produced from natural gas, gasoline, or diesel fuels through steam reforming processes to mitigate air pollution from ships.

• Journal of the Korean Solar Energy Society
• /
• v.34 no.2
• /
• pp.32-43
• /
• 2014

This study set out to identify the importance of each factor influencing facility selection with a survey among public medical facilities under the category of public buildings and apply the importance of economy, technology and environment with the weighting factor method, thus proposing optimal application plans. The research content of each section can be summarized as follows:1) Estimated energy consumption according to the energy simulation was 65,129MWh/yr, which was 18.7% higher than that according to the calculation equation. Of the energy consumption, more than 80% was used by heating and cooling facilities and construction facilities, and 20% was used by electronics such as medical equipments and in and outdoor lighting. 2) The results of a survey on the factors influencing the importance when selecting a new and renewable energy system reveal that the upper items had a priority in economy, environment, and technology in the descending order and that the lower item shad a priority in initial investments, maintenance and repair costs=energy costs, supply reliability, energy efficiency and $CO_2$ emissions in the descending order. 3) The application alternatives were analyzed in economy, technology, and environment. As a result, a geothermal system turned out to be the most excellent one a cross all the upper and lower comparison items. Of the other systems, a solar thermal system was superior in initial investments, maintenance and repair costs, and energy efficiency, where as a photovoltaic system was superior in energy costs, supply reliability, and $CO_2$ emissions. 4) As for the mixed application ratio among economy, technology, and environment, when the percentage of a geothermal system was approximately 80% or higher in anew and renewable energy system, it was the best and most optimal application plan.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.22 no.4
• /
• pp.448-453
• /
• 2012

There are many researches to develop robots that improve its mobility to adapt in various uneven environments. In the paper, a hybrid wheeled and legged mobile robot is designed and a obstacle avoidance algorithm is proposed based on low power walking using LRF(Laser Range Finder). In order to stabilize the robot's motion and reduce energy consumption, we implement a low-power walking algorithm through comparison of the current value of each motors and correction of posture balance. A low-power obstacle avoidance algorithm is proposed by using LRF sensor. We improve walking stability by distributing power consumption and reduce energy consumption by selecting a shortest navigation path of the robot. The proposed methods are verified through walking and navigation experiments with the developed hybrid robot.