SSB, VHF 등의 장비로 구성된 무선국의 통신시스템은 지금도 중요한 정보전달의 수단으로 이용되고 있으며, 무선국의 통신권을 확보하기 위하여 산악, 도서등의 원거리에 설치되는 장비는 전용회선을 사용하여 원격제어로 송·수신을 행하고 있다. 그러나 무선국에서 다수의 사용자가 다수의 장비에 임으로 접속하고 운용을 해야하는 환경에서는 ICS(Integrated Communication System:통합통신시스템)의 회선접속 제어기가 요구된다. 본 논문에서는 ICS의 개발을 위하여 ASK(Amplitude Shift Keying) 변조방식에 의한 U(Push To Talk) 제어와 신호의 전송회로를 구성하여 실험하였고, 멀티-프로세싱에 의한 회선접속 제어기를 설계하여 통합 통신운용에 대한 알고리즘을 연구하였다. Keying에 의하여 PTT 신호를 단속하였고 지속되는 PTT 신호에 음성신호를 합성시켜 전송시키는 형태의 ASK 변조방식을 취하여 전송되도록 하였고, 회선접속 제어기는 master와 다수의 slave 프로세서를 멀티-프로세싱의 직렬데이터 전송방식으로 프로세서 상호간에 데이타가 전달되도록 구성하였다. 이에 따른 S/W 는 멀티-프로세싱의 인터럽트기법을 최대한 활용하여 원하는 회선에 정확히 접속되어 통신이 이루어지도록 설계하였다. 따라서 이 연구는 주파수 자원의 고갈과 통신량의 증가에 대한 대책의 일환으로 저비용의 시설로 재래식 장비의 운용 효율을 증대시키는 기술을 개발하는데 목적이 있다.
Journal of Advanced Marine Engineering and Technology
/
제35권6호
/
pp.842-848
/
2011
다중통신을 지원하는 하이브리드 통신 제어보드는 저전력의 8-bit 마이크로콘트롤러인 ATxmega128A1으로 설계하였으며, 마이크로콘트롤러는 다중통신을 위한 모뎀과 GPS 모듈 등을 시리얼 인터페이스 하기 위한 8개의 UART 포트가 갖추어져 있으며, 내부에 2K 바이트의 프로그램 매개변수와 프로그램이 동작하는데 필요한 데이터를 저장할 수 있는 EEPROM과 128K 바이트의 플래시 메모리 및 프로그램이 실행되는 8K 바이트의 SRAM으로 구성되어 있다. 항로표지의 원격 관리를 CDMA, TRS, RF 등 하이브리드 통신을 이용하면 개별 통신 방식별로 음영지역이 존재하는 경우에도, 최적의 통신방식을 선택하여 통신을 수행하게 됨으로써, 통신 음영지역의 해소가 가능하다. 또한 통신장치마다 동일한 데이터 프레임을 사용함으로써 데이터의 호환성을 높였다. 실험은 30일 동안 각 부표에서 매 5분마다 데이터를 취득하였으며, 데이터 수신율은 85 % 이상을 보였다.
Journal of Advanced Marine Engineering and Technology
/
제33권8호
/
pp.1254-1260
/
2009
DMA 무선원격 제어시스템은 저전력의 8 bit 마이크로콘트롤러인 ATmega 2560으로 설계하였으며, 마이크로콘트롤러는 CDMA 모뎀과 GPS 모듈 등을 시리얼 인터페이스를 하기 위한 4개의 UART 포트가 갖추어져 있으며, 내부에 4K 바이트의 프로그램 매개변수나 프로그램이 동작하는데 필요한 데이터를 저장할 수 있는 메모리(EEPROM)와 256K 바이트의 플래시 메모리 및 프로그램이 실행되는 내부 메모리(SRAM)로 구성되어 있다. 제작되어진 800 MHz CDMA 모뎀과 GPS를 사용한 항로표지 원격관리 시스템의 해상통신 거리를 측정한 결과 10 km 정도의 통신 거리를 확인할 수 있어서며, -80 dBm의 수신신호감도를 나타내었다.
대부분의 최신 자동차들은 편안하고 안전한 운전 환경을 위해 다양한 종류의 ECU들을 탑재하고 있다. ECU들 사이의 효율적인 통신을 위해 대부분의 자동차 제조사들은 Controller Area Network(CAN) 프로토콜을 사용하고 있다. 그러나 CAN은 데이터 인증을 제공하지 않는다. 이러한 취약점 때문에 CAN은 메시지 재생공격에 취약하다. 본 논문은 자동차 내부 네트워크에 적용 가능한 현실적인 메시지 인증 기법을 제안한다. CAN 데이터 프레임의 제한적인 공간을 고려하여, 데이터와 메시지 인증 코드 (MAC)를 동시에 전송하기 위해서는 짧은 길이의 MAC을 사용하는 것이 가장 적합하다. 그러나 짧은 길이의 MAC은 암호학적 안전성을 충분히 보장하지 않기 때문에 안전성을 보장하기 위한 추가적인 조치가 필요하다. 본 연구에서 제안한 메시지 인증 기술은 CAN의 제한된 데이터 페이로드를 고려하기 때문에 차량 내부의 안전한 네트워크를 설치하는데 유용하게 활용될 수가 있다.
빛은 인류가 시작되고나서 현재까지 언제나 인간의 일생에 커다란 영향을 미치는 에너지원이다. 이로 인해 모든 인간은 빛과 함께 할 때 보다 편안함을 느낄 수 있으며 안정된 마음으로 아름다움과 행복을 추구하려는 본능을 가지게 된다. 본 논문에서는 퍼지제어 시스템을 이용하여 외부환경요인을 각각 조합하여 불확실한 내용을 정량적인 값으로 변환하여 LED 조명으로 표현하기 위해 알고리즘을 설계하고, 실내에서 이용 가능한 감성조명용 LED 제어기 회로를 설계 및 제작하였다. 외부환경요소인 온도, 습도, 조도 값을 센서를 통해 제어기로 받아 들이고 이 값들을 퍼지제어 알고리즘을 통해 최적조명값으로 변환되어 인간이 느끼기에 편안한 감성조명을 LED 디밍제어를 통해 표현하고자 한다.
International journal of advanced smart convergence
/
제7권4호
/
pp.50-56
/
2018
The Internet of Things (IoT) and Visible Light Communication (VLC) is opening up new services in lighting industry by integrating sensory network features in addition to standard illumination functionality. In this progressive developments, the next generation lighting devices for smart homes are capable to sense the environmental conditions and transfer the captured data through lights to gateway controller to access remotely. The smart home environmental sensor information's are few kbps only so VLC systems need to built-in with low rate light connectivity to transfer data to the gateway. To provide error free communication, the quality of a received light signal is important to be considered when designing an VLC receiver. Therefore, this paper proposes the design of robust low rate IoL receiver design using NCP302 voltage detector for micro controller to adapt the IoT/IoL front end module for system integration. To evaluate the proposed system performance, the Arduino UNO based IoT/IoL controller designed with lighting, sensors and lights connectivity interfaces. The experimental result shows that the robust interference rejection is feasible on proposed VOL receiver and possible to have an error-free communication up to 10 kbps at a low SNR using OOK modulation.
스마트 홈 분야가 주목받고 있음에 따라 하나의 컨트롤러로 다양한 전자제품을 통합적으로 제어하기 위한 연구가 진행되어 왔다. 기존 연구들은 별도의 범용 컨트롤러나 리모컨 역할을 하는 애플리케이션을 개발하고 제품별 제어 화면을 구성하여 전자제품을 제어하는 방식이다. 그러나 이러한 방식들은 전용의 컨트롤러를 개발해야 하고 전자제품마다 별도의 제어 화면을 구성하여 전자제품을 제어하기 때문에 다양한 전자제품을 제어하기에는 적합하지 않다. 본 논문에서는 웹 기반의 원격제어 플랫폼을 제안한다. 다양한 전자제품의 사용자 인터랙션을 분류하여 여러 장치에서 적용 가능한 범용 사용자 인터페이스를 정의하고 API로 구현한다. 제안하는 API를 IPTV와 자동차 내비게이션 장치에 적용하여 웹 브라우저만 있으면 제어가 가능함을 확인한다. 또한, 연속적인 제어 요청을 효율적으로 처리하기 위하여 다수의 제어 요청을 그룹핑하는 기법을 제안하고 응답시간과 데이터 사용량의 개선을 확인한다.
Anwary, Arif Reza;Lee, Young-Il;Jung, Hee;Kim, Yong-Gi
International Journal of Fuzzy Logic and Intelligent Systems
/
제8권1호
/
pp.82-86
/
2008
The article presents ARTMAP and Fuzzy BK-Product approach underwater obstacle avoidance for the Autonomous underwater Vehicles (AUV). The AUV moves an unstructured area of underwater and could be met with obstacles in its way. The AUVs are equipped with complex sensorial systems like camera, aquatic sonar system, and transducers. A Neural integrated Fuzzy BK-Product controller, which integrates Fuzzy logic representation of the human thinking procedure with the learning capabilities of neural-networks (ARTMAP), is developed for obstacle avoidance in the case of unstructured areas. In this paper, ARTMAP-Fuzzy BK-Product controller architecture comprises of two distinct elements, are 1) Fuzzy Logic Membership Function and 2) Feed-Forward ART component. Feed-Forward ART component is used to understanding the unstructured underwater environment and Fuzzy BK-Product interpolates the Fuzzy rule set and after the defuzzyfication, the output is used to take the decision for safety direction to go for avoiding the obstacle collision with the AUV. An on-line reinforcement learning method is introduced which adapts the performance of the fuzzy units continuously to any changes in the environment and make decision for the optimal path from source to destination.
Recent advancement in wireless communications and electronics has enabled the development of low power sensor network. Wireless sensor network are often used in remote monitoring control applications, health care, security and environmental monitoring. Wireless sensor networks are an emerging technology consisting of small, low-power, and low-cost devices that integrate limited computation, sensing, and radio communication capabilities. Sensor network platform for health care has been designed, fabricated and tested. This system consists of an embedded micro-controller, Radio Frequency (RF) transceiver, power management, I/O expansion, and serial communication (RS-232). The hardware platform uses Atmel ATmega128L 8-bit ultra low power RISC processor with 128KB flash memory as the program memory and 4KB SRAM as the data memory. The radio transceiver (Chipcon CC1000) operates in the ISM band at 433MHz or 916MHz with a maximum data rate of 76.8kbps. Also, the indoor radio range is approximately 20-30m. When many sensors have to communicate with the controller, standard communication interfaces such as Serial Peripheral Interface (SPI) or Integrated Circuit ($I^{2}C$) allow sharing a single communication bus. With its low power, the smallest and low cost design, the wireless sensor network system and wireless sensing electronics to collect health-related information of human vitality and main physiological parameters (ECG, Temperature, Perspiration, Blood Pressure and some more vitality parameters, etc.)
The CAN (Controller Area Network) system is the most dominant protocol for in-vehicle networking system because it provides bounded transmission delay among ECUs (Electronic Control Units) at data rates between 125Kbps and 1Mbps. And, many automotive companies have chosen the CAN protocol for their in-vehicle networking system such as chassis network system because of its excellent communication characteristics. However, the increasing number of ECUs and the need for more intelligent functions such as ADASs (Advanced Driver Assistance Systems) or IVISs (In-Vehicle Information Systems) require a network with more network capacity and the real-time QoS (Quality-of-Service). As one approach to enhancing the network capacity of a CAN system, this paper introduces a CAN system with dual communication channel. And, this paper presents a distributed message allocation method that allocates messages to the more appropriate channel using forecast traffic of each channel. Finally, an experimental testbed using commercial off-the-shelf microcontrollers with two CAN protocol controllers was used to demonstrate the feasibility of the CAN system with dual communication channel using the distributed message allocation method.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.