• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.6
• /
• pp.21-27
• /
• 1998

Electrical and optical characteristics of ZnS:Mn/ZnS:Tb multilayer TFEL devices were investigated for multi-color electroluminescent display applications. Emission spectra of M $n^{2+}$ and T $b^{3+}$ ions were observed from ZnS:Mn/ZnS:Tb multi-layer TFEL devices, and were very broad from 540 nm to 640 nm. Saturation luminance measured at 155 V was 1025 Cd/$m^2$. C-V, $Q_{t}$ - $V_{p}$ curves showed that the phosphor capacitance ( $C_{p}$ ) and the insulator capacitance ( $C_{i}$ ) were 13.5nF/$\textrm{cm}^2$ and 60 nF/$\textrm{cm}^2$, respectively. Threshold voltage( $V_{thl}$) was shown to decrease from 126 V to 93 V due to the increase of the applied voltage from 155 V to 185 V, which was attributed to the increase of the polarization charge. The equation for the calculation of the threshold voltage as a function of the applied voltage was proposed for the first time. The calculated threshold voltage agreed well with the data obtained from the measurement.t.t.t.

• International Journal of Highway Engineering
• /
• v.14 no.3
• /
• pp.131-140
• /
• 2012

Lane markings such as edgelines, centerlines, and lines that delineate lanes generally provide drivers with the various information for safe driving. Drivers can easily recognize the lane markings through the color differences between the markings and road surfaces during the daytime. However, it is a bit difficult for drivers to perceive them during the nighttime due to the lack of artificial lights. Although the glass beads with the 1.5-refractive index have been used to improve the visibility of the lane markings during the nighttime, it is still difficult for drivers to recognize the lane markings properly, especially during the rainy nighttime, which may often lead to traffic accidents. To improve the retroreflectivity and visibility of the lane markings during the rainy nighttime, the high refractive beads with the 2.4-refractive index are essentially required, but they do not work appropriately during the dry nighttime. Thus, the mixed materials with the 1.5, 1.9, and 2.4-refractive beads should be considered for the satisfactory implementation of the lane markings. This study reveals the best mixing rates of the beads by conducting benefit-cost analysis under various weather conditions in Korea. The analysis results show that the lane markings with the 100% of the 2.4-refractive beads provide the highest visibility of lane markings regardless of the roadway conditions, but the benefit-cost (B/C) ratio of the bead mixture is merely 0.46. The best mixing rate of the beads, from the highest B/C ratio viewpoint, was identified as the mixture with a 80% of 1.5-refractive beads and a 20% of 2.4-refractive beads. Some limitations and future research agenda have also been discussed.

• Korean Journal of Food Science and Technology
• /
• v.36 no.6
• /
• pp.943-951
• /
• 2004

As storing ginger roots under optimum conditions takes high cost, ginger roots are commonly stored in underground tunnels where the maintenance of optimum temperature and humidity is difficult. One of the methods fur long term storage of ginger roots is freezing. The objective of this research was to evaluate effect of storage temperatures and packaging methods on the quality of minced ginger prepared with frozen stored ginger. The minced ginger prepared with frozen stored ginger at $-20^{\circ}C$ was packed in bags, glass bottles and tubes, and then stored at 5 and $-20^{\circ}C$ for quality evaluation at 4 and 15 week-intervals. The changes of surface color, total free sugars, free amino acids and volatile compounds were less in the combined treatment samples than in control during storage, regardless of the storage temperature. The tube packing was the best for maintaining quality of minced ginger during storage among tested packaging methods. Sensory results showed that the minced ginger with the combined treatment and packed in tubes could be stored at 5 and $-20^{\circ}C$ for 12 and 45 weeks, respectively, without a significant drop in palatability.

• Applied Biological Chemistry
• /
• v.43 no.1
• /
• pp.39-45
• /
• 2000

The stability of vitamin A, $B_1,\;B_2,\;B_6$, C in aqueous multivitamin solutions was carried out by means of estimation of reaction velocity and the results are described in this paper. The stability of vitamin A, $B_1$ and C due to thermal degradation method in aqueous multivitamin solutions was evaluated at 40, 50, 60 and $70^{\circ}C$ up to 40 days. The shelf-lives of vitamin A, B₁ and C in this preparation, calculated using the Arrhenius equation, were 1493, 449 and 639 days at $25^{\circ}C$ respectively. Examination was made on the effect of initial concentration of vitamin $B_2$$(C_0)$ on light fading of vitamin $B_2$ in aqueous multivitamin solutions and it was found that the fading progressed according to the following formula : $-{\frac {dc}{dt}}=K_c\;{\frac C{C_0}}$ where Kc is apparent light-fading rate constant relate to $C_0$. Photodecomposition of vitamin $B_6$ in aqueous multivitamin solutions was apparently first order kinetics and was stable in polyethylene>brown color>glass container to sunlight. Photodecomposition of vitamin $B_6$ in four seasons also investigated.

• The Korean Journal of Mycology
• /
• v.27 no.4 s.91
• /
• pp.243-248
• /
• 1999

To compare the morphological and cultural characteristics of Cordyceps militaris, forming conditions of artificial fruiting body production were investigated in this experiment. The stroma shapes of artificial fruiting body were confirmed to club and/or stick. However, both shapes were same color as a orange. Perithecia of stroma was semi-egg shape and was ranged from $30{\sim}90{\times}90{\sim}130\;{\mu}m$ and it's asci was narrowly cylindric. Ascospore of perithecia was belong to filiform and multiseptate. The conidia of C. militaris was centurally grown and shaped with globose, long clavate type, floccose, centrally raised during anamorph stage. When it was cultured between glass and PP bottle, production of artificial fruiting body, pinheading ratio and total yield were higher in PP bottle. The optimum illumination was 1,000 lx for the those production. The culture medium of barley, wheat and hulled rice showed higher artificial fruiting body compared to that of silkworm. Pinheading and yield of it's isolates was decreased at more than three subsequent transculture.

• Korean Journal of Food Science and Technology
• /
• v.37 no.1
• /
• pp.30-37
• /
• 2005

To mass-produce useful biopolymer films, chitosan/gelatin blend films were prepared by solution casting method. Effects of mixing ratio, tensile strength (TS), elongation (E) at break, total color difference (${\Dalta}E$), opacity, water vapor permeability (WVP), oxygen permeability (OP), and thermal properties on chitosan/gelatin blend films properties were investigated. TS, E, ${\Dalta}E$, opacity, WVP, and OP values were 58.24-22.01 MPa, 13.11-24.67%, 1.86-17.45, 0.3104-1.2161 nmO.D./${\mu}m$, $1.6875-1.7225ng{\cdot}m/m^{2}{\cdot}s{\cdot}Pa$, and $2.2380{\times}10^{-7}-2.2975{\times}10^{-7}\;mL{\cdot}{\mu}m/m^{2}{\cdot}s{\cdot}Pa$, respectively. TS of blend films decreased, while E, ${\Dalta}E$, and opacity increased with increasing chitosan content. WVP of blend films did not show any significant relationship with mixing ratio and thickness of blend films. Miscibility of films was examined over entire composition range by thermogravimetric analyzer (TGA) and dynamic mechanical analyzer (DMA). TGA results showed gelatin is more thermally stable than chitosan and some interactions among functional groups of two biopolymers. Glass transition temperature $(T_{2})$ of films as determined by DMA decreased with increasing content of chitosan in the blend. Results of thermal analysis indicate high miscibility among polymer components in the blend.

• Korean Journal of Food Science and Technology
• /
• v.28 no.1
• /
• pp.1-7
• /
• 1996

Three formulations were used to prepare the cellulose-based edible films consisting of hydrocolloid and lipids; film A made by coating method, films B and C by emulsion method, which were formed in a thin layer glass plate and then dried. Films A, B and C were all approximately 0.03 mm thick with 1-3% moisture, 59-68% lipid, and almost whitish color. Film A was better in tensile strength, and lipids affected water vapor permeability on three films, in which films A and B did not differ significantly. Water vapor permeability of film A did not change but those of films B and C decreased significantly after storage for 8 weeks at $-15^{\circ}C$. Oxygen transmission rate and oxygen permeability of films A and C did not differ and changed significantly after 8-week storage at $-15^{\circ}C$. Under scanning electron microscope (SEM) observation on the structural characteristics of each film, film A indicated relatively uniform and smooth surface coatings of beeswax, while films B and C had individual lipid crystals and could be discerned. As a result, film A was better than films B and C in respect of physical properties, but the selection of useful film depended upon which physical property was more functional. Moreover, it was desirable in some cases for using films B and C because of their easiness of preparation and cold storage durability. It will be further needed to investigate how to formulate films B and C to have more unique surface characteristics, and to reduce water vapor and oxygen transmission rates.

• Applied Chemistry for Engineering
• /
• v.32 no.6
• /
• pp.690-694
• /
• 2021

Carbon spheres (CS) were fabricated using glucose as a precursor in the hydrothermal method. Hollow TiO₂ (H-TiO₂) spheres with 200 nm, 500 nm, and 1,200 nm were synthesized by CS/TiO₂ core-shell particles via a sol-gel and calcination method. H-TiO₂ spheres with nano and micron sizes were characterized using FE-SEM, HR-TEM, and X-ray diffraction. The CIE color coordinate, solar reflectance, and heat shield temperatures of H-TiO₂/polyacrylate (PA) composite film were investigated using a UV-Vis-NIR spectrometer and homemade heat insulation temperature measuring device. H-TiO₂/PA composites exhibit excellent thermal insulation since the hollow structure filled with dry air has low thermal conductivity and near infrared light reflecting performance. The thermal insulation increased with increasing the hollow sphere (HS) size on H-TiO₂/PA composites. The PA composite film mixed with H-TiO₂ filled with 1200 nm HS reduced the heat shield temperature by 26 ℃ compared to that of the transparent glass counterpart.

• Journal of Technologic Dentistry
• /
• v.40 no.4
• /
• pp.217-224
• /
• 2018

Purpose: The aim of this study was to evaluate accuracy of three type complete mandibular denture of before and after polymerization. Methods: Mandibular edentulous model was selected as the master model. 15 study models were made by Type IV stone. Wax complete mandibular dentures were produced by the denture base and artificial teeth. Before and after curing, STL files were obtained using a blue scanner. By superimposing the digitized complete mandibular denture data(after curing) with the CAD-reference(before curing) three-dimensionally, visual fit-discrepancies were drawn by calculating the root mean square (RMS) and visualized on a color-difference map. Each calculated RMS-value was statistically analyzed by 1-way analysis of variance(ANOVA) (${\alpha}=.05$). Results: Mean(SD) RMS-values was OM group $88.98(6.10){\mu}m$, BM group $82.35(13.46){\mu}m$, BDM group $77.83(9.46){\mu}m$. The results of the 1-way ANOVA showed no statistically significant differences in the RMS values of the Three groups for the material (P > .241). Conclusion : Deformation of artificial teeth position was observed in all groups after resin polymerization. But the values, all group were within the clinically acceptable range. The values of BDM group showed the least deformation than the other two groups.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.31 no.3
• /
• pp.35-41
• /
• 2023

In this study, silicon sludge generated in semiconductor manufacturing process is recycled and applied as materials for pigments and paints. In detail, metallic impurities are removed from silicon sludge to obtain plate-like silicon sludge powder (SW-sludge), which is then coated with titanium dioxide via sol-gel method (TCS-sludge). SW-sludge and TCS-sludge are dispersed in hydrophilic transparent varnish and sprayed onto glass substrates to observe the possibility for the application as materials for pigments and paints. Notably, the applicability of TCS-sludge-based paint is improved compared to SW-sludge-based paint after the titanium dioxide coating. Moreover, the color of TCS-sludge-based paint turns into white. Accordingly, it is confirmed that the applicability and hydrophilicity are improved by the presence of outer titanium dioxide layer. In this regard, it is expected that the recycled TCS-sludge may be a future material for the application as pigments and paints.