• Corrosion Science and Technology
• /
• 제8권6호
• /
• pp.217-222
• /
• 2009

The production of advanced high strength steels requires the improvement of cooling technology. The use of high cooling rates allows relatively low levels of expensive alloying additions to ensure sufficient hardenability. In classical annealing and hot-dip galvanizing lines a mixing station is used to provide atmosphere gas containing 3-5% hydrogen and 97-95% nitrogen in the various sections of the furnace, including the rapid cooling section. Heat exchange enhancement in this cooling section can be insured by the increased hydrogen concentration. Drever International developed a patented improvement of cooling technology based on the following features: pure hydrogen gas is injected only in the rapid cooling section whereas the different sections of the furnace are supplied with pure nitrogen gas; the control of flows through atmosphere gas management allows to get high hydrogen concentration in cooling section and low hydrogen content in the other furnace zones. This cooling technology development insures higher cooling rates without additional expensive hydrogen gas consumption and without the use of complex sealing equipments between zones. In addition reduction in electrical energy consumption is obtained. This atmosphere control development can be combined with geometrical design improvements in order to get optimised cooling technology providing high cooling rates as well as reduced strip vibration amplitudes. Extensive validation of theoretical research has been conducted on industrial lines. New lines as well as existing lines, with limited modifications, can be equipped with this new development. Up to now this technology has successfully been implemented on 6 existing and 7 new lines in Europe and Asia.

• 대한기계학회논문집A
• /
• 제35권9호
• /
• pp.977-982
• /
• 2011

보강롤 구동 4 단 냉간압연기에서 작업롤과 보강롤 사이의 접촉력으로 인해 발생된 작업롤의 수평력을 고찰하였다. 본 수평력은 작업롤을 수평방향으로 휘게하고 롤갭 형상을 그 만큼 변화시킨다. 본 논문에서는 압연을 정상상태라고 가정하여 작업롤의 수평력을 예측할 수 있는 수식모델을 제시하였다. 해석에 사용된 소재는 고-실리콘(약 3%) 강판이었다. 수평력의 비-정상거동을 고찰하기 위해서 삼차원 유한요소모델을 채용하였다. 두 가지 모델을 이용하여 작업롤의 수평력은 보강롤의 중심으로부터 작업롤의 중심이 벗어난 길이에 따라 변한다는 결과를 얻었다. 그리고 작업롤의 수평력을 최소화 시킬 수 있는 작업롤의 최적 중심이탈 길이를 도출하였다.

• 대한금속재료학회지
• /
• 제48권5호
• /
• pp.377-386
• /
• 2010

An investigation was conducted into the effects of $\kappa$-carbides on the cracking phenomenon, which often occurred in cold-rolled light-weight steel plates. Three kinds of steels were fabricated by varying the C content, and their microstructures and tensile properties were investigated. In the two steels that contained a high carbon content, the band structures of ferrites and $\kappa$-carbides that were severely elongated along the rolling direction were well developed, whereas continuous arrays of $\kappa$-carbides were formed in the steel that contained a low carbon content. Detailed microstructural analyses of the deformed region beneath the tensile fracture surface showed that the cracks initiated at arrays of $\kappa$-carbides or $\kappa$-carbides formed interfaces between the band structures, which initiated cleavage fractures in the ferrite bands, while the bands populated with a number of $\kappa$-carbides did not play an important role in propagating the cracks. Thus, the minimization of interfacial $\kappa$-carbides or $\kappa$-carbide arrays by increasing the carbon content was essential for preventing cracking from occurring during cold rolling.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 제5회 압연심포지엄 신 시장 개척을 위한 압연기술
• /
• pp.307-316
• /
• 2004

This study examined the cause of the wrinkle defect which is frequently encountered in wire rod rolling of low carbon steel$(C0.08\~0.13wt.\%)$. Even a small defect on the surface of rolled bars can easily develop into fatal cracks during cold heading process of low carbon steel, and it is therefore necessary to minimize inherent defects on the surface of hot rolled bars. Hot rolling process of low carbon steel was analyzed to identify the cause of the wrinkle defect in conjunction with FE analysis. The integrated analysis revealed that the wrinkle defect initiated in the first stage of rolling, and it was at the billet edge where severe deformation and drastic temperature drop were present. To elucidate the micro-mechanical mechanism of the wrinkle defect, hot compression tests were carried out at various temperatures and strain rates using Gleeble-3800. The surface profile of the each other compressed specimens was compared, and rough surface lines were observed at relatively low temperatures. Those surface defects can develop into wrinkles during multi-pass rolling. To control the wrinkle defect in rolling, it is necessary to design an adequate caliber which can minimize the loss of ductility, and thereby prevent flow localization. To use the result of this study fur other steels, the quantitative measure of the wrinkle defect and flow localization parameter should be proposed.

• 한국정보통신학회논문지
• /
• 제3권4호
• /
• pp.895-905
• /
• 1999

This paper identifies a linear time-invariant mathematical model of each stand of a five-stand tandem cold mill to design a robust $H_\infty$ thickness controller by applying input and output data sets to N4SID (Numerical algorithms for Subspace State Space System Identification) method. The input-output data sets describe interstand interference in the process of tandem cold rolling and are obtained from a nonlinear simulator of the tandem cold mill. In result, it is shown that the identified model well approximates the nonlinear model than a Taylor linearized model. Furthermore, uncertainties including roll eccentricity and incoming strip variation are quantitatively analyzed from the plot of maximum singular values.

• 대한기계학회논문집
• /
• 제19권9호
• /
• pp.2142-2153
• /
• 1995

A digital preview controller using optimal LQ control theory is suggested for tandem cold mills to achieve a remarkable improvement of the thickness accuracy. Optimal preview control system is constructed for each rolling stand of tandem cold mills for which the blocked noninteracting control is carried out, and it is compared with the optimal LQ control system which has only feedback control. And in the cases that all/some of disturbance inputs are previewable, full and partial preview controllers are designed, and their performance effects are compared and discussed. The simulation results show that the performance of tandem cold mills can be improved largely through partial preview control.

• 한국초전도ㆍ저온공학회논문지
• /
• 제4권2호
• /
• pp.16-20
• /
• 2002

Bi-axially textured Ni tapes for YBCO coated conductors were Prepared by cold rolling and heat treatment of Ni Powder compacts. The Ni powder used in this study was 5 urn in particle size and 99.99 % in purity. The process of this study consists of filling of hi powder into a rubber mold, cold-isostatically Pressing and sintering of the powder compacts at 110$0^{\circ}C$ for 6h in 96 % Ar - 4 % H$_2$ atmosphere. The sintered compacts were cold rolled with a 5 % step reduction ratio into a 100 micron-thick tapes and then heat-treated at 100$0^{\circ}C$ for various time periods. The (200) texture of Ni tape was successfully developed through the recrystallization heat treatment of the cold rolled Ni tapes. At 100$0^{\circ}C$, the degree of texture of the heat-treated Ni tapes seems not to be significantly affected by the heat-treatment time. The short heat treatment of S min was sufficient to develop the complete (200) cube texture. The degree of in-Plane and out-of-plane texture of the prepared Ni tapes was 8-10$^{\circ}$. The heat treated Ni tapes consisted of equiaxed grains with a size 50-70 microns. and the AFM sol-face roughness was as smooth as 3 nm.

• 한국재료학회지
• /
• 제21권10호
• /
• pp.556-562
• /
• 2011

We carried out this study to evaluate the grain refining in and the mechanical properties of alloys that undergo severe plastic deformation (SPD). Conventional rolling (CR) and cross-roll rolling (CRR) as SPD methods were used with Ni-20Cr alloy as the experimental material. The materials were cold rolled to a thickness reduction of 90% and subsequently annealed at $700^{\circ}C$ for 30 min to obtain a fully recrystallized microstructure. For the annealed materials after the cold rolling, electron back-scattered diffraction (EBSD) analysis was carried out to investigate the grain boundary characteristic distributions (GBCDs). The CRR process was more effective when used to develop the grain refinement relative to the CR process; as a result, the grain size was refined from $70{\mu}m$ in the initial material to $4.2{\mu}m$ (CR) and $2.4{\mu}m$ (CRR). These grain refinements have a direct effect on improving the mechanical properties; in this case, the microhardness, yield and tensile strength showed significant increases compared to the initial material. In particular, the CRR-processed material showed more effective values relative to the CR-processed materials. The different texture distributions in the CR (001//ND) and CRR (111//ND) were likely the cause of the increase in the mechanical properties. These findings suggest that CRR can result in materials with a smaller grain size, improved texture development and improved mechanical properties after recrystallization by a subsequent annealing process.

• 소성∙가공
• /
• 제29권1호
• /
• pp.37-43
• /
• 2020

Increasing the critical current density of superconducting wire is one of the difficult challenges in the field of superconductivity. It is well known that the higher volume fraction of uniformly dispersed α-Ti is able to enhance the critical current density of superconducting material NbTi because α-Ti serves as a flux pinning center. The volume fraction of α-Ti highly depends on the grain size of NbTi because α-Ti precipitates at the grain boundaries or triple points. For this purpose, we investigated the effect of initial microstructures of NbTi obtained from hot rolling in various temperature conditions on the critical current density. In addition, subsequent heat treatment was assigned to precipitate α-Ti and groove rolling/cold drawing was adopted to produce a wire with a diameter of about 1.0 mm. It was observed that the band structure was formed after hot rolling at 500~600℃. It was also found that the volume fraction of α-Ti after hot rolling at 500~600℃ was higher and it led to the highest critical current density.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2002년도 ICCAS
• /
• pp.57.1-57
• /
• 2002

$\textbullet$ This system executes the algorithm that makes the various types of shape to the flat shape. $\textbullet$ In old system, we could not develop and test the new shape control algorithms $\textbullet$ We developed the PC based cold mill shape control system. $\textbullet$ It can be added on the new shape control algorithm and is cost-effective and maintained easily. $\textbullet$ The shape control system consists of the shape controller, the MMI system and the Shape data sewer.