• Journal of Environmental Science International
• /
• v.20 no.4
• /
• pp.519-525
• /
• 2011

A three-dimensional ecological model(EMT-3D) was applied to DAS1 in Tokyo Bay. The simulated results of DAS1 were in good agreement with the observed values. The result of sensitivity analysis showed that photolysis coefficient and extinction coefficient were important factor for dissolved DAS1, and photolysis coefficient, extinction and POC partition coefficient for PAHs in particulate organic matter. Mass balance of DAS1 in Tokyo Bay was calculated by using the simulated results of EMT-3D.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.3
• /
• pp.451-456
• /
• 2004

This present experimental study has dealt with the heat transfer characteristics of plastic particle slurry which flows in a circular tube. This type of slurry is suggested for heat transfer enhancement effect cause by random and vortex effect of plastic particle dispersed in water. As a result, the thermal boundary layer becomes thin so the heat transfer coefficient on the tube wall more increase compare to pure water flow. This experimental test section was composed with stainless pipe which has the length of 2000mm, inner pipe diameter of 14mm and outer pipe diameter of 60mm. The most effective and important parameter of this experiment is plastic packing factor(PPF). The focuses of these results are pressure drop and heat transfer coefficient. As results, the friction factor of plastic particle slurry becomes higher at laminar flow region than pure water because of buoyancy effect of plastic particle but the local heat transfer coefficient becomes higher.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2009.01a
• /
• pp.492-497
• /
• 2009

Computer-Generated Hologram (CGH) is made for three dimensional image of a virtual object. Error diffusion method is used for the phase quantization of CGH, and it is known to be effective to the image quality improvement of the reconstructed image. However, the image quality of the reconstructed image from the CGH using error diffusion method depends on the selection of error diffusion coefficient. In this paper, we derived the relational expression to obtain the error diffusion coefficient from the position of the input object and size of the input object for CGH. As a result, the method of this thesis was able to obtain an excellent reconstructed image compared with the case to derive the error diffusion coefficient from only the position of the input image.

• KIEAE Journal
• /
• v.11 no.6
• /
• pp.37-42
• /
• 2011

This Paper aims for analyzing the effect of opening types on wind-driven ventilation performance in basement parking lots of apartment. The scale model of basement parking lot was made, wind tunnel tests conducted. Wind pressure of three opening types was measured, wind pressure coefficient calculated. As the result, it showed that the air flow pattern of stack type opening was strongly changed by wind direction, but it was almost not at scuttle vent type. But, as for the difference of wind pressure coefficient, stack type opening was more than the other two types.

• Communications for Statistical Applications and Methods
• /
• v.15 no.4
• /
• pp.509-516
• /
• 2008

We derive the influence function on the coefficient of variation. Empirical influence function and Sample influence function are used to verify the validity of the derived influence function. To show the validity of the influence function, we carry out simulations with random samples from normal distribution $N(20,1^2)$ and $N(20,5^2)$, respectively. The simulation result proves that the derived influence function is very accurate in estimating changes in the coefficient of variation when an observation is deleted.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.226-229
• /
• 2004

The temperature difference between die and workpiece has been frequently caused to various surface defects. The distribution and change for the temperature of forged part should be analyzed to prevent the generation of various defects related with the temperature. The surface temperature changes were mainly affected by the interface heat transfer coefficient. Therefore, the coefficient is necessary to predict the temperature changes of die and workpiece. The temperature calculated by FEM result might be well compared with the measured temperature. However, it is impossible to measure directly the temperature distribution of forged part. Therefore, the comparisons between measured temperature and predicted values are preformed by the microstructure in various temperature. Since the differences of microstructure could be obvious, the temperature criteria is set near by the incipient melting temperature. The predicted temperatures are well coincided with the measured values.

• Journal of the Korean Society of Visualization
• /
• v.11 no.1
• /
• pp.16-21
• /
• 2013

In this study, diffusion coefficients of 20 kDa FITC-dextran in 2% agarose gel with different cell concentrations were measured using fiberoptic-based fluorescence recovery after photobleaching technique. As increasing cell concentration suspended in agarose gel, the diffusion coefficients were decreased. The diffusion coefficient of agarose gel which contains $10{\times}10^6$ cells/ml was decreased to 11% that of in agarose gel without cells. The distribution of fluorescence dye in 3D scaffold was also simulated. The simulation result shows that the diffusion coefficient is more significant factor than the scaffold structure.

• Proceedings of the KSRS Conference
• /
• 1998.09a
• /
• pp.89-94
• /
• 1998

Seasonal variation of attenuation coefficient spectra in Japan sea was extracted from underwater radiance/irradiance spectra observed by a moored buoy system developed by National Space Development Agency of Japan (NASDA). The buoy was deployed 9 months from August 31, 1996 to June 1, 1997. Throughout this period, it was collecting downward irradiance and upward radiance spectra under water at the depth of 1.5m and 6.5m everyday. The dairy averaged diffused attenuation coefficient spectra and underwater reflectance spectra were calculated. The results were compared with the absorption spectra of filtered samples obtained by validation cruises, which carried out 5 times during the moored period. Also, the natural fluorescence of chlorophyll a were extracted from the upward radiance spectra observed at 1.5m depth. The seasonal variation of the calculated attenuation coefficient spectra and the natural fluorescence were examined. The result shows a weak blooming of phytoplankton on November and a large blooming on April.

• Proceedings of the KSR Conference
• /
• 2004.10a
• /
• pp.472-476
• /
• 2004

In this study, we investigate the change characteristic of friction coefficient of disk brake lining for rolling stock according to disk type, The actual brake tests were carried out under constant brake force and operating sequence by using dynamo-tester. Test results showed that instant friction coefficient was higher in the case of devided disk type rather than single body disk type, Also, averge friction coefficient was appeared similer to the above result. It is thought that ,in the case of devided disk type, friction resistance was increased due to the gap between both side of half disk.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05b
• /
• pp.185-188
• /
• 2005

This study selected three different specified concrete strength types of mixture which were applied to domestic seawater concrete structure and measured compressive strength and chloride diffusion coefficient and composed the formula of prediction model of chloride diffusion coefficient in order to provide the useful data for concrete mix decision of seawater structures. As a result, the formula of prediction model of chloride diffusion coefficient which set W/C and compressive strength as parameters and performed multiplex regression analysis which was based on the mathematical theory was confirmed more reliable than the formula of prediction which was composed existing water-cement ratio function.