• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.759-764
• /
• 2001

Heat (mass) transfer characteristics have been investigated on the endwall of a large-scale linear turbine cascade passage under a combustor-level high free-stream turbulence with a large length scale. Local heat (mass) transfer coefficients are measured by using the naphthalene sublimation technique. The result shows that local heat (mass) transfer on the endwall is greatly enhanced in the central region of the turbine passage, but there is no noticeable change in the local heat (mass) transfer in the region suffering severe heat load. Under the high free-stream turbulence, the local heat (mass) transfer coefficient shows more uniform distribution and its average value across the whole endwall region is increased by 26% of that at low turbulence condition. The heat (mass) transfer data on the endwall strongly supports that well-organized vortices near the endwall tends to suffer an suppression by the high free-stream turbulence.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 학술대회 논문집 정보 및 제어부문
• /
• pp.178-180
• /
• 2004

In this work, we propose new method of sigma filtering for efficient filtering and preserving edge regions in DCT Domain. In block-based image compression technique, the image is first divided into non-overlapping $8{\times}8$ blocks. Then, the two-dimensional DCT is computed for each $8{\times}8$ block. Once the DCT coefficients are obtained, they are quantized using a specific quantization table. Quantization of the DCT coefficients is a lossy process, and in this step, noise is added. In this work, we combine IDCT matrix and filter matrix to a new matrix to simplify filtering process to remove noise after IDCT in spatial domain, for each $8{\times}8$ DCT coefficient block, we determine whether this block is edge or homogeneous region. If this block is edge region, we divide this $8{\times}8$ block into four $4{\times}4$ sub-blocks, and do filtering process for sub-blocks which is homogeneous region. By this process, we can remove blocking artifacts efficiently preserving edge regions at the same time.

• Tribology and Lubricants
• /
• 제23권3호
• /
• pp.123-129
• /
• 2007

This paper presents a theoretical model for the analysis of double-bumped AFBs. The stiffness and damping coefficients of the double bump vary depending on the external load and its friction coefficient. In the case of a lightly loaded condition where only the upper bump contributes to deformation, the double bump is in the single active region. In the case of a heavily loaded condition where both the upper and lower bumps contribute to deformation, the double bump is in the double active region. So the double bump can be either in the single or double active region depending on vertical deflection. The equivalent stiffness and damping coefficients of the bump system are derived from the vertical and horizontal deflection of the bump, including the friction effect. A static and dynamic performance analysis is carried out by using the finite difference method and the perturbation technique. The results of the performance analysis for a double-bumped AFB are compared with those obtained for a single-bumped AFB. This paper successfully proves that a double bumped AFB has higher load capacity, stiffness, and damping than a single-bumped AFB in a heavily loaded condition.

• Tribology and Lubricants
• /
• 제36권3호
• /
• pp.147-152
• /
• 2020

This paper is within the framework of an adhered complete contact problem wherein the contact between a half plane and sharp edged indenter, both of which are elastic in character, is constituted. The eigensolutions of the contact shear and normal stresses, σ_rq and σ_q, respectively, are evaluated via asymptotic analysis. The ratio of σ_rq/σ_qq is investigated and compared with the coefficient of friction, μ, of the contact surface to observe the propensity to slip on the contact surface. Interestingly, there exists a region of |σ_rθ/σ_θθ| ≥ |μ|. Thus, slipping can occur, although the problem is solved under the condition of an adhered contact without slipping. Given that a tribological failure potentially occurs at the slipping region, it is important to determine the size of the slipping region. This aspect is also factored in the paper. A simple example of the adhered contact between two elastically dissimilar squares is considered. Finite element analysis is used to evaluate generalized stress intensity factors. Furthermore, it is repeatedly observed that slipping occurs on the contact surface although the size of it is extremely small compared with that of the contacting squares. Therefore, as a contribution to the field of contact mechanics, this problem must be further explained logically.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.99-104
• /
• 2002

In this paper the influence or specimen length on flexural compressive strength and parameter or equivalent rectangular stress block of polymer concrete was evaluated. For this purpose, a series of C-shaped specimens subjected to eccentric compression were tested using four different length-to-depth ratios(from 1.0, 2.0, 3.0 and 4.0) of specimens with compressive strength of 1,020kgf/cm$^2$. Results indicate that for the region of h/c$\leq$3.0 the reduction in equivalent rectangular stress block depth and flexural compressive strength with increase of length-to-depth ratios was apparent but for the region of h/c$\geq$3.0 they were nearly constant. It means that for the region of h/c$\geq$3.0 effect of specimen length on equivalent rectangular stress block depth and flexural compressive strength was negligible. It was also founded that the effect of specimen length on v, a coefficient of strength, that was from 0.84 to 0.86 regardless of h/c was petty. Finally, predictive equation is, suggested by using modified law of effect of specimen length and results.

• 동력기계공학회지
• /
• 제4권3호
• /
• pp.25-33
• /
• 2000

This study represents three-dimensional turbulent flow characteristics around an axial fan measured at the operating point ${\varphi}=0.32$, which is equivalent to the maximum flowrate region, by using three-dimensional fiber-optic type LDA system. This LDA system is composed of a 5 W Argon-ion laser, two optics in back-scatter mode, three BSA's, a PC, and a three-dimensional automatic traversing system. A kind of paraffin fog is used for laser particles in this study. Mean velocity profiles around an axial fan along the downstream radial distance show that the streamwise and the tangential components exist as a predominant velocity and have the maximum value at the radial distance ratio 0.8, while the radial component has a small scale distribution and its flow direction is inward except a part of blade tip. The turbulent intensity profiles show that the radial component exists the most greatly. And also the turbulent kinetic energy shows about 60% as a maximum value at the radial distance ratio 0.9. Moreover, the Reynolds shear stresses do not exist at upstream flow, but the streamwise and the radial components of them show about 20% as a maximum value at the radial distance ratio 0.9 at downstream flow.

• 한국전산유체공학회지
• /
• 제6권4호
• /
• pp.26-34
• /
• 2001

The flow past a circular cylinder forced to vibrate transversely is numerically simulated by solving the two-dimensional Navier-Stokes equations modified by the vibration velocity of a circular cylinder at a Reynolds number of 164. The higher-order finite difference scheme is employed for the spatial discretization along with the second order Adams-Bashforth and the first order backward-Euler time integration. The calculated cylinder vibration frequency is between 0.60 and 1.30 times of the natural vortex-shedding frequency. The calculated oscillation amplitude extends to 25% of the cylinder diameter and in the case of the lock-in region it is 60%. It is made clear that the cylinder oscillation has influence on the wake pattern, the time histories of the drag and lift forces, power spectral density and phase diagrams, etc. It is found that these results include both the periodic (lock-in) and the quasi-periodic (non-lock-in) state. The vortex shedding frequency equals the driving frequency in the lock-in region but is independent in the non-lock-in region. The mean drag and the maximum lift coefficient increase with the increase of the forcing amplitude in the lock-in state. The lock-in boundaries are also established from the present direct numerical simulation.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2001년도 춘계 학술대회논문집
• /
• pp.181-188
• /
• 2001

The flow past a circular cylinder forced to vibrate transversely is numerically simulated by solving the two-dimensional Wavier-Stokes equations modified by the vibration velocity of a circular cylinder at a Reynolds number of 164. The higher-order finite difference scheme is employed for the spatial discretization along with the second order Adams-Bashforth and the first order backward-Euler time integration. The calculated cylinder vibration frequency is between 0.60 and 1.30 times of the natural vortex-shedding frequency. The calculated oscillation amplitude extends to $25\%$ of the cylinder diameter and in the case of the lock-in region it is $60\%$. It is made clear that the cylinder oscillation has influence on the wake pattern, the time histories of the drag and lift forces, power spectral density and phase diagrams, etc. It is found that these results include both the periodic (lock-in) and the quasi-periodic (non-lock-in) state. The vortex shedding frequency equals the driving frequency in the lock-in region but is independent in the non-lock-in region. The mean drag and the maximum lift coefficient increase with the increase of the forcing amplitude in the lock-in state. The lock-in boundaries are also established from the present direct numerical simulation.

• The Journal of Asian Finance, Economics and Business
• /
• 제4권2호
• /
• pp.37-44
• /
• 2017

This research is devoted to the development of methods general and standard methodological approaches and approbation those for the evaluation of economic potential and level of concentration of the regions of Kazakhstan. This paper presents the results of development of the authors on the selection and justification of the methodological approaches for quantitative evaluation of the economic potential (the degree of territorial differentiation of the profile) and concentration of regions. In this study, we used scientific methods: method of analysis the main trends of economic development, and method of evaluation of concentration of the region. Based on the analysis of foreign techniques developed and tested methodical approaches to the assessment of the economic potential (index and coefficient methods). Proposed methodological approaches to the assessment profile of the territory and developed a system of indicators, which includes an aggregated index of spatial concentration, which accurately reflects the concentration of production in the region. This study shows the results of the analysis of the potential regional disparities and trends of economic development of Kazakhstan. By using, the proposed methodology shows the possibility of their use; we calculated the indicators of integrated assessment of the economic potential and indicators of spatial concentration.

• 한국광학회지
• /
• 제7권4호
• /
• pp.357-362
• /
• 1996

스핀 코팅으로 제작한 MNA/PMMA 고분자박막의 두께 및 굴절율과 소광계수를 결정하였다. 타원해석 스펙트럼을 분석하여 박막의 두께 및 투과영역에서의 굴절율을 결정하고 광흡수 스펙트럼으로부터 흡수영역에서의 소광계수 스펙트럼을 역방계산하였다. 이 소광계수 스펙트럼을 가장 잘 나타내는 고전적 Lorentz 진동자 상수들과 양자역학적 진동자 상수들을 각각 구하고 이들 진동자에 의한 복소굴절율 스펙트럼들을 비교하였다. 이 방법은 대부분의 고분자박막의 두께 및 굴절율과 소광계수 스펙트럼을 구하는데 적용될 수 있으며 고분자박막의 광학적 특성을 규정짓는데 매우 유용하게 사용될 수 있겠다.