• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.9
• /
• pp.87-92
• /
• 1998

TM mode coupling coefficients for a generic five-layer DFB structure with trapezoidal and triangular gratings are calculated using the extended additional layer method. To determine the unperturbed field distributions of TM modes, a grating region is replaced by a new uniform layer whose inverse dielectric constant is the average value of the inverse dielectric constant of grating region in both longitudinal and transverse directions. Based on the self-consistent check, the validity of this method is established by comparing the results calculated by partitioning the grating region up to six uniform layers.

• Journal of Advanced Marine Engineering and Technology
• /
• v.21 no.5
• /
• pp.557-563
• /
• 1997

The unsteady flow in three-dimensional cubic cavity with narrow channel at upper region is investigated experimentally for three kinds of Reynolds number, 1*10/sup 4/, 3*10/sup 4/ and 5*10/sup 4/ based on the cavity width and cavity inlet mean flow velocity. Instant velocity vectors are obtained simultaneously at whole field by PIV(Particle Image Velocimetry). Wall pressure distributions are estimated using Poisson equation from the velocity data. Results of PIV reveal that severe unsteady flow fluctuation within the cavity are remarkable at all Reynolds numbers and sheared mixing layer phenomena are also found at the region where inlet driving flow is collided with the clock-wise rotating main primary vortex. Instant velocity profiles reveal that deformed forced vortex formation is observed throughout the entire region and spanwise kinetic energy migration is conspicuous.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.234-237
• /
• 2007

To protect a satellite and electronic equipment from the acoustic load generated by rocket propulsion system, many launch vehicle use acoustic blanket. Acoustic load is main source of random vibration working on the payload. Most high frequency region of the acoustic loads is reduced by payload fairing skins and acoustic blanket, but low frequency region is not. In order to reduce acoustic load of low frequency region, we designed array resonator panel which was made of composite materials. Insertion loss capacity of the payload fairing with acoustic blanket was verified from PLF acoustic test in the acoustic chamber.

• Environmental and Resource Economics Review
• /
• v.11 no.3
• /
• pp.377-396
• /
• 2002

This paper investigates whether an inverted U relationship between pollution and economic development could be found in the Seoul metropolitan region using a panel data for the period of 1985~1999. We uses a model with a more flexible random coefficients specification which allows for a greater degree of regional heterogeneity. The emissions of sulfur dioxidetotal($SO_2$), suspended particulates(TSP), nitrogen dioxide($NO_2$), and carbon monoxide(CO) were selected as four major pollutants. We found that the emissions of these pollutants per capita except sulfur dioxidetotal exhibited inverted U shapes with per capita gross regional domestic product (GRDP). We also noted that the turning points for Seoul metropolitan region occured at a range of incomes, from $3,000 to $5,000 per capita.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.20 no.2
• /
• pp.272-278
• /
• 2017

In this paper, we consider a single-channel amplitude comparison monopulse system(SCACMS). The monopulse ratio curve(MR-C) of the SCACMS can be controlled by an amplitude difference between sum and different signal, a phase difference and the coefficient of the signal processor. We first propose the SCACMS with multiple variables, and then apply a genetic algorithm to optimize the multiple variables in terms of minimizing a root mean square error. The simulation results show that when three variables of the SCACMS are jointly optimized, the linear region of the MR-C can be extended approximately 187 % compared to that of two variables.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05b
• /
• pp.254-259
• /
• 1996

The hydraulic tests for 16$\times$16 JDFA were performed to obtain the pressure loss coefficients using the FACTS. The pressure loss coefficients are calculated by converting the each properties of experimental values for inlet region, mixing vane grid, outlet region and core region by performing a power fit of the pressure loss coefficient values to the corresponding Reynolds number. The test results are compared with the existing calculated values and evaluated by using the CALOPR code in terms of pressure drop. It is turned out that the differences between the test results and the calculated values are about by 3.8% for the pressure loss coefficients and by 8.5% for the pressure drop.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.7
• /
• pp.37-44
• /
• 1997

A dadaptive refinement tetrahedron mesh has been presented for using in full band GaAs monte carlo simulation. A uniform tetrahedron mesh is used without regard to energy values and energy variety in case of the past full band simulation. For the uniform tetrahedron mesh, a fine tetrahedron is demanded for keeping up accuracy of calculation in the low energy region such as .GAMMA.-valley, but calculation time is vast due to usin gthe same tetrahedron in the high energy region. The mesh of this study, thererfore, is consisted of the fine mesh in the low energy and large variable energy region and rough mesh n the high energy. The density of states (DOS) calculated with this mesh is compared with the one of the uniform mesh. The DOS of this mesh is improved th efive times or so in root mean square error and the ten times in the correlation coefficient than the one of a uniform mesh. This refinement mesh, therefore, can be used a sthe basic mesh for the full band GaAs monte carlo simulation.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2004.05a
• /
• pp.33-38
• /
• 2004

Molecular modeling of gas permeation through zeolite membranes with/without intercrystalline region was carried out. Molecular dynamics (MD) and Monte Carlo (MC) simulations were performed to estimate the diffusion coefficient and adsorption parameters respectively, and our proposed combined method of molecular simulation techniques with a permeation theory (CMP) was used to estimate gas permeability. The calculated permeability of gases (Ar, He, Ne, $N_2$, $0_2$, $CH_4$) at 301 K for the single crystal membrane model was about one order of magnitude larger than the experiential values, although the dependence on the molecular weight of the permeating species agreed with experiments. On the other hand, the estimated permeability using the diffusivity and adsorption parameters of the intercrystalline region model was in good agreement with the experiments. The consistency between experiments and the estimated values means the importance of considering the intercrystalline region and the validity of CMP method to predict the performance of zeolite membranes.

• Journal of Sensor Science and Technology
• /
• v.15 no.4
• /
• pp.263-268
• /
• 2006

We have demonstrated a highly sensitive temperature sensor using an etched single mode fiber with a thermally expanded core region. Large core size of thermally expanded core facilitates access to evanescent wave by the wet etching. The etched region was surrounded by a low dispersive external medium with high thermo-optic coefficient. Due to the large difference between the dispersion property of the fiber and that of the external medium, the device reveals a cut-off properties at spectral region. The cut-off wavelength was shifted by the variations of the environmental temperatures because of thermo-optic effect of the external medium. The sensitivity of the fabricated device was found to be $45nm/^{\circ}C$.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.42 no.2
• /
• pp.78-85
• /
• 2000

The moment equations of the concentration distribution for the multi-region model are derived using the method of moment. The method originally devised by Aris is to obtain the concentration moments satisfying a given PDE (Partial Differential Equation. The method of moment is used to obtain the first five moments (0th to 4to) that satisfy the model PDE. Each moment of the concentration distribution for the model equation is plotted for the dimensionless time and gave similar results except the skewness and the kurtosis. The results of the analysis show the physical meaning of each moment. The comparisons with the number of regions or the global interaction coefficient give a possibility to determine the parameters of the multi-region model with the analytical concepts.