• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2004.06a
• /
• pp.13-23
• /
• 2004

The characteristics of cesium and cobalt removal from soil around the TRIGA reactor using the electrokinetic method were analyzed and a device to restrain the pH increase in the soil column was suggested. When a NaCl solution was used as the electrolyte to raise the electric field strength, a precipitate was formed in the cathode in the soil column, resulting in a low removal efficiency. Thus, an acetate buffer solution (compound solution of $CH_3COONa$ and $CH_3COOH$) was injected into the soil column and acetic acid was periodically infected into the cathode reservoir to restrain any pH increase. Many $Cs^{2+}$ and $Co^{2+}$ ions were transferred by electromigration rather than electroosmosis during the initial remediation period, and no precipitate was formed in the soil column. 96% of the total amount of cesium in the soil column was removed after 5.9 days, while 94% of the total amount of cobalt was removed. Furthermore, the residual concentrations predicted by the developed model were similar to those obtained by experiment.

• Korean Journal of Materials Research
• /
• v.13 no.2
• /
• pp.88-93
• /
• 2003

Co/Ti bilayer structure in Co salicide process helps to the improvement of device speed by lowering contact resistance due to the epitaxial growth of $CoSi_2$layers. We investigated the epitaxial growth and interfacial mass transport of $CoSi_2$layers formed from $150 \AA$-Co/Ti structure with two step rapid thermal annealing (RTA). The thicknesses of Ti layers were varied from 20 $\AA$ to 100 $\AA$. After we confirmed the appropriate deposition of Ti film even below $100\AA$-thick, we investigated the cross sectional microstructure, surface roughness, eptiaxial growth, and mass transportation of$ CoSi_2$films formed from various Ti thickness with a cross sectional transmission electron microscopy XTEM), scanning probe microscopy (SPM), X-ray diffractometery (XRD), and Auger electron depth profiling, respectively. We found that all Ti interlayer led to$ CoSi_2$epitaxial growth, while $20 \AA$-thick Ti caused imperfect epitaxy. Ti interlayer also caused Co-Ti-Si compounds on top of $CoSi_2$, which were very hard to remove selectively. Our result implied that we need to employ appropriate Ti thickness to enhance the epitaxial growth as well as to lessen Co-Ti-Si compound formation.

• Journal of the Korean institute of surface engineering
• /
• v.40 no.1
• /
• pp.23-31
• /
• 2007

The objective of this study is to investigate the effect of Al addition on the reaction behavior of cobalt with molten zinc. Pure cobalt specimen was immersion tested in the three kinds of molten zinc (pure, 0.12%Al added and 0.24%Al added) baths at $460^{\circ}C,\;490^{\circ}C\;and\;520^{\circ}C$. For the understanding of degradation processes, specimens were analyzed with scanning electron microscope (SEM) and energy dispersive spectrum (EDS), and electrochemical stripping method. When 0.12% and 0.24% Al was added in molten zinc baths, three intermetallic compounds layers of ${\gamma},\;{\gamma}_1,\;and\;{\gamma}_2$ were formed on the Co matrix and ${\beta}_1$ layer was not formed between the Co matrix and the ${\gamma}$ layer. Particles of CoAl intermetallic compound were formed at the interface between the ${\gamma}_2$ layer and zinc melt and they did not adhere to the Co-Zn intermetallic layer. Weight loss of the Co specimen increased as Al content in the molten zinc increased and the relationship of weight loss vs. immersion time followed parabolic rate law. Rate controlling process for the reaction rate of Co with Al added molten zinc was analyzed as the diffusion process of Al atom through a boundary layer between the ${\gamma}_2$ layer and the Al added zinc melt.

• Journal of the Korean Chemical Society
• /
• v.47 no.6
• /
• pp.585-590
• /
• 2003

Cobalt oxygen carrier complex N,N'-ethylenebis(3-methoxysalycylideneiminato)cobalt(II), Co(3MeOsalen) was prepared at $25{\circ}C$. UV and visible absorption spectra of the complex and hydrazobenzene were studied in non-aqueous solvent methanol in the range of wavelength 200-600 nm. The oxidation of hydrazobenzene by oxygen in non-aqueous solvent is catalysed by Co(3MeOsalen). In the presence of triphenylphosphine($PPh_3$), the rate decreases in methanol. This is presumably attributable to the coordination of $PPh_3$ to the Co(3MeOsalen), resulting in the catallytically inactive compound. The initial rates of the oxidation of hydrazobenzene with the ligand triphenylphosphine were measured by the theoretical values of the rates, Rate=$k_1+k_2K_1[P]/1+K_1[P]+K_1K_2[P]^2$. This fact would be a poorer σ-donor ligand than methanol.

• Korean Journal of Crystallography
• /
• v.18 no.1_2
• /
• pp.21-25
• /
• 2007

When a $CH_2Cl_2$ solution of the dipyridyl species L' (N,N'-bis-(1-pyridin-4-yl-ethylidene)-naphthalene-1,5-diamine) was layered onto the top of a MeOH solution of $Co(NO_3)_2{\cdot}6H_2O$, a molecular cobalt compound [$CoL_2(MeOH)(NO_3)_2$] (1), not a coordination polymer, was formed. X-ray structural analysis of compound 1 revealed that it contains the pyridyl-amine ligand L (N1-(4-imino-1-methyl-but-2-enylidene)-naphthalene-1,5-diamine), instead of L'. Structure of compound 1 strongly suggests that the original ligand L' has been hydrolyzed to ligand L during the reaction.

• Corrosion Science and Technology
• /
• v.6 no.4
• /
• pp.147-153
• /
• 2007

This study sought to investigate the reaction of Co-binder containing tungsten with molten zinc. Four kinds of Co-W alloys (pure, 10%W, 20%W, 30%W) were prepared using the powder metallurgy method. The specimens were immersion-tested in molten pure zinc baths at $460^{\circ}C$. To evaluate the corrosion property in molten zinc, the weight loss of the specimen was measured after the immersion tests at different immersion times (10~300 min.). Co-10%W alloys, compared with pure cobalt, showed no effect of tungsten addition on the reaction rate in molten zinc. The relationship between the weight loss and the square root of immersion period represents a straight line in both pure cobalt and Co-10%W alloy. The Co-Zn reaction layer in Co- 1O%W alloy consists of $\gamma2$, $\gamma1$, $\gamma$ and ($\beta1$ phases. The rate of weight loss significantly increases and the weight loss behavior is not well accord with the linear relationship as the tungsten content in the Co-W alloy increases. The $\beta1$ layer was not formed on the Co-20%W alloy and neither was a stable Co-Zn intermetallic compound layer found on the Co-30%W alloy. The main cause of increase in reaction rate with increasing tungsten content is related with the instability of the Co-Zn reaction phases as seen on micro-structural analysis.

• Journal of Environmental Health Sciences
• /
• v.23 no.2
• /
• pp.12-23
• /
• 1997

The biosynthesis of galactolipid, galactose and the fatty acid composition in E. cdi and B. subtills treated with potassium dichromate(PD, 500 ppm, 500 ppm), potassium chromate(PC, 500 ppm, 500 ppm), cobalt chloride(CC, 100 ppm, 10 ppm) and methylmercuric chloride(MC, 100 ppm, 10 ppm) during the culture were analyzed to compare with the control. The growth rate of cells, the contents of monogalactosyldiglyceride(MGDG), digalactosyldiglyceride(DGDG) and total lipid in the metal compound treatments were lower as compared with the control. And too, the contents of galactose utilized for the biosynthesis of galactolipids in these strains in the various metal compounds treatments were inhibited. The fatty acids used for the MGDG and DGDG formation in E. coli and B. subtills treated with each metal compounds during the culture were showed to the variant compositional change.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.2
• /
• pp.21-27
• /
• 2000

To develop the underfill materials which are required for the new process of semi-conductor industry, the properties of epoxy/anhydride/cobalt(II) catalyst system with two types of fused silica(1 $\mu\textrm{m}$, 8 $\mu\textrm{m}$) are studied as a function of filler fraction. According to the curing profile, the optimum catalyst amount was 1.0 wt% for full curing at the conditions of $160^{\circ}C$/l5 min., and we could conclude that the viscosity has superior effect on the real flaw through the relationship between surface tension and viscosity data. The underfills which were filled with 1 $\mu\textrm{m}$ fused silica did not show good flowability, but they should be useful by improving the viscosity for a future process which has small gaps. The underfills which were filled with 8 $\mu\textrm{m}$ fused silica showed good flowability when the filler contents were 55~60 vol%. The model which was referred by Matthew can predict the real flow length only when the underfill has high viscosity and low surface tension.

• Korean Journal of Materials Research
• /
• v.8 no.6
• /
• pp.484-492
• /
• 1998

The formation mechanism of the epitaxial cobalt silicide from Co/Ti/OOO) Si structure has been investigated. The transition temperature of CoSi to CoSi, was found to increase with increasing the Ti interlayer thickness, which may be owing to the occupation of the tetrahedral sites by Ti atoms in the CoSi crystal structure as well as the blocking effect of the Ti interlayer on the diffusion of Co. Also, the Co- Ti-O ternary compound formed at the metal! Si interface at the begining of silicidation, which seems to play an important role in epitaxial growth of Co silicide. The final layer structures obtained after a rapid thermal annealing of the Cot Ti/( 100) Si bi-layer structure turned out to be Ti oxide/Co- Ti-Si/epi-$CoSi_2$/OOO)

• Elastomers and Composites
• /
• v.49 no.1
• /
• pp.59-65
• /
• 2014

In this study, in order to complete curing reaction of the molding compound comprising an epoxy/anhydride at $71^{\circ}C$ for 40 hours, metal coordination complexes such as cobalt (II) acetylacetonate, potassium acetylacetonate, iron (III) acetylacetonate and chromium (III) octoate as a catalyst were applied to the epoxy/anhydride compounds respectively. The weight ratio of an epoxy part/an anhydride part was adjusted to improve the mechanical properties of the molding compound. According to the experimental results, an epoxy/anhydride compound containing chromium (III) octoate showed a high conversion at $71^{\circ}C$ for 40 hours as well as a proper processability at room temperature among the several metal coordination complexes. For the mechanical properties of the cured epoxy/anhydride compound, the compounds containing weight ratio from 0.9/1 to 0.5/1 of the epoxy part/anhydride part with chromium (III) octoate showed the high flexural strength, and higher compressive strength was shown with increasing of the hardener part.