• Elastomers and Composites
• /
• v.48 no.4
• /
• pp.282-287
• /
• 2013

Slot coating has been widely spread in photo resist coating on glass for flat display monitor. High quality of coating is required as high quality of image in display is needed. Coating quality in the slot coating is divided into nozzle direction quality and machine direction quality. Nozzle direction quality is related to flow uniformity inside the die whereas machine direction quality is related to die lip design and operational conditions. In this study coating uniformity in the machine direction of slot coating has been investigated through computer simulation. Die lip angle and die lip length were considered as outside die geometry and coating speed was considered as operational condition. Coating behavior has been analyzed and coating quality has been evaluated through computer simulation. Coating thickness decreased and coating uniformity increased as coating speed increased. However, the stability of meniscus formation was reduced and subsequently coating stability was reduced as coating speed increased. Coating thickness deviation decreased as die lip angle increased in down stream die. Coating thickness decreased and time to reaching steady state increased as increased die lip length in down stream die.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.5
• /
• pp.60-66
• /
• 2000

Coating immobilization is the process by which the wet coating applied to paper or paperboard reaches the final form. A coating immobilization point is defined as the solids content reached during drying where no further redistribution of coating materials occurs. Good control of coating immobilization is important in producing coated paper and paperboard with consistent high quality. This paper discusses the technical concepts of how coatings immobilize, and describes the importance of good immobilization control on coating holdout and coating structure. The use of soy protein polymers to modify the coating immobilization point is discussed. Soy proteins, because of their interaction with coating pigments, make a significant contribution to the immobilization characteristics of coastings. This technology gives the formulator options for changing the immobilization point to improve the performance of the coating. The importance of immobilization on casting uniformity, microporosity and sheet qualities is discussed, including binder migration, mottle, gluing, and print quality.

• Journal of the Semiconductor & Display Technology
• /
• v.22 no.4
• /
• pp.119-123
• /
• 2023

This study is normal orientation technology of slit coating equipment to improve the quality of curved displays. Currently, the demand for curved displays is increasing significantly due to advantages such as screen immersion or design in various industries. Accordingly, changes in the display coating process are essential. In the curved display coating process, unlike the existing flat coating process, the nozzle must be rotated along the curvature of the curved surface to spray the coating solution. The coating solution must be applied while maintaining a uniform thickness. If the thickness of the coating liquid applied to the target surface is non-uniform, the quality of the product may be degraded such as image quality deterioration and light spreading. This paper presents technology and experimental results for keeping the nozzle of slit coating equipment perpendicular to the curved surface and is expected to contribute to the quality improvement of curved displays.

• Journal of Korean Society for Quality Management
• /
• v.42 no.2
• /
• pp.179-187
• /
• 2014

Purpose: Since several problems were found when present non-conducting metal coating process was applied to mass production, we study and develop to improve those problems. Methods: In this paper, a couple of analysis methods such as surface hardness, XPS spectrum analysis, morphology, and reflection ratio were used. Results: This paper suggest a new possibility of Non-conducting thin metal coating method that has quality of mass production phase without UV coating process. Conclusion: By the result of analysis, we can set optimized process conditions of the electro deposition coating using electron beam.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.39 no.2
• /
• pp.158-164
• /
• 1994

These experiment were conducted to evaluate the environmentally acceptable polymers, and 10 polymers were used in these study, and to investigate conductivity, germination percentage, water uptake of polymeric coating soybean seed. The conductivity of polymeric coating seed is higher than that of none coating seed and the highest conductivity was obtained with waterlock coating seed among the 10 polymer coating seed. As the soaking time was long, the conductivity was increased. The conductivity of large seed was higher than that of small seed, and that of long period storage seed was higher than that of short period storage seed. The effects of seed coating polymers on uptake water were various, and daran 8600 inhibited uptake water of low quality seed. The waterlock, captan, klucel and sacrust was rised germination percentage, and daran 8600 was declined germination percentage, and the effect of coating polymers on germination percentage of low quality seed was higher than that of high quality seed.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.2
• /
• pp.159-166
• /
• 2015

Slot-die coating is well known technique to guarantee a uniformly coated layer and is compatible with roll-to-roll process. In actual roll-to-roll slot-die coating process, the lateral difference of coated layer thickness is observed. An experimental study was performed to improve the coating quality. Coating speed and coating gap were selected as the experimental factors. A full factorial, statistical method was conducted to optimize the process conditions. Based on the results of repeated experiment, the lowest deviation of lateral thickness (700 nm, <10%) was achieved at 10 m/min coating speed and $300{\mu}m$ coating gap. This result has significance because such optimized process guideline can be utilized with all process improvement in various coating applications.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2008.05a
• /
• pp.47-70
• /
• 2008

Cost efficiency is today the primary requirement in the paper and board industry. This has led therefore, to a greater preponderance of products with specifically designed functionality to take account of current industry needs. Continually increasing machine coating speeds together with these new coating colour components have put more emphasis on the importance of the correct rheology and water retention of the coating colours to achieve good runnability and end product quality. In the coating process, some penetration of the aqueous phase, to the base paper or board must occur to anchor the pre-coating to the base or the topcoat to the pre-coat. The aqueous phase acts as a vehicle not only for the binder, but also for the other components. If this water or material penetration is not controlled, there will be excessive material shift from the coating colour to the base, before immobilization of the coating colour will stop this migration. This can result in poor machine runnability, unstable system and uneven coating layer, impacting print quality. The performance of rheology modifiers or thickeners on the coating color have tended to be evaluated by the term, "water retention". This simple term is not sufficient to explain their performance changes during coating. In this paper we are introducing a new concept of "material retention", which takes note of the total composition of the coating colour material and therefore goes beyond the concept of only water retention. Controlled material retention leads to a more uniform z-directional distribution of coating colour components. The changes that can be made to z-directional uniformity will have positive effects on print quality as measured by surface strength, ink setting properties, print gloss, mottling tendency. Optical properties, such as light scattering, whiteness and light fastness delivery should also be improved. Additionally, controlled material retention minimizes changes to the coating colour with time in re-circulation giving less fluctuation in quality in the machine direction since it more closely resembles fresh coating for longer periods. Use of the material retention concept enables paper and board producers to have more stable runnability (i.e. lower process costs), improved end product quality (i.e. better performance of used chemicals) and/or optimized use of coating colour components (i.e. lower total formulation cost)

• Journal of the Korea Institute of Building Construction
• /
• v.10 no.3
• /
• pp.57-64
• /
• 2010

This study is to analyze the effects of aluminum form surface coating material on surface quality of concrete. When observing the surface quality of concrete affected by the change of aluminum form surface coating material, in general, as the number of use of the coating material increased, the surface quality of concrete decreased and good surface quality was shown in plywood (hereinafter PW). For epoxy (hereinafter EP) resin, when applying form remover, good surface quality was shown. For the surface roughness of concrete by the application form oil of form remover and the number of use of the coating material, as the number of use increased, highest surface roughness value was shown which meant the leveling was bad, but the surface roughness value in EP and PW was the lowest. Just for EP, when applying form remover, surface roughness value was low. For the number of void for concrete by the application of form remover and the number of use of the coating material, In general, the number of void which was generated when applying form oil the remover decreased.

• Korean Journal of Metals and Materials
• /
• v.46 no.5
• /
• pp.289-295
• /
• 2008

The effect of the alloy elements(Si/Mn) ratio on the coating quality including wettabilty with molten zinc, galvannealing kinetics and crater has been investigated in interstitial-free high strength steel(IFHSS) containing Si and Mn. When the Si/Mn ratio was below 0.75, IF-HSS exhibited a good wettability leading to a good galvannealed coating quality after annealing at $800^{\circ}C$ for 40s in $15%H_2-N_2$ mixed gas with dew point $-60^{\circ}C$. In contrast, the wettability and galvannealed coating quality were deteriorated in the Si/ Mn ratio above 0.75. It is shown that they have relevance to oxides forms by selective oxidation on the steel surface. The oxide particles dispersed on the steel surface with a surface coverage of below 40% resulted in good wettability and galvannealed coating quality. The oxide particle is mainly consisted of $Mn_2SiO_4$ with low contact angle in molten zinc. On the other hand, the continuous oxide layer on the steel surface, such as network- and film-type,caused to poor wettability and galvannealed coating quality. The coverage of oxide layer was above 80%, and its chemical species was $SiO_2$ with high contact angle in molten zinc. Consequently, the Si/Mn alloy ratio played an importance role in galvannealed coating quality of IF-HSS.

• Food Science of Animal Resources
• /
• v.31 no.6
• /
• pp.834-842
• /
• 2011

Gelatin-based edible coating was used to reduce the oxidative degradation of low-fat sausages (LFSs) stored at $4^{\circ}C$ for 8 wk under vacuum packaging. The gelatin coating reduced thiobarbituric acid-reactive substances and peroxide value by 21.5 and 26.5%, respectively, compared with the controls. The moisture barrier effect was significantly better for the gelatin coating compared to the control. The gelatin coating reduced moisture loss in sausages by 32.6% over the control. However, the gelatin coating of sausages did not inhibit the growth of either the total plate counts or L. monocytogenes. Data show that gelatin can effectively be used as a natural antioxidative and moisture barrier coating to extend the quality and shelf life of sausages.